HG/T 2143-1991 Glass-lined equipment nozzles
Basic Information
Standard ID:
HG/T 2143-1991
Standard Name: Glass-lined equipment nozzles
Chinese Name:
搪玻璃设备 管口
Standard category:Chemical industry standards (HG)
state:Abolished
Date of Release1991-08-19
Date of Implementation:1992-01-01
Date of Expiration:2007-03-01
standard classification number
Standard ICS number:Chemical Technology>>Chemical Equipment>>71.120.99 Other Chemical Equipment
Standard Classification Number:Chemical Industry>>Chemical Machinery and Equipment>>G94 Non-metallic Chemical Machinery and Equipment
Publication information
publishing house:Chemical Industry Press
other information
Introduction to standards:
HG/T 2143-1991 Glass-lined equipment pipe openings HG/T2143-1991 standard download decompression password: www.bzxz.net
Some standard content:
Chemical Industry Standard of the People's Republic of China
Glass Equipment
Subject Content and Scope of Application
This standard specifies the style, basic parameters and dimensions, technical requirements, etc. of nozzles for glass equipment. HG/T 2143-91
This standard is applicable to the pipe nozzles for glass equipment and pipe fittings with nominal pressure less than or equal to 1.0MPa and medium temperature higher than -20℃ and lower than or equal to 200℃:
2 Reference standards
GB1804 Tolerances and fits, limit deviations of dimensions without tolerances ZBG94004 Technical conditions for glass equipment
3 Types, basic parameters and dimensions
3.1 Basic parameters and dimensions of type A pipe nozzles are shown in Figure 1 and Table 1.D
Approved by the Ministry of Chemical Industry of the People's Republic of China on August 19, 1991 and implemented on January 1, 1992
Nominal pressure PN
Nominal diameter
HG / T 2143 -- 91
Dimensions Pei
Reference weight
HG/T2143-91
3.2 Basic parameters and dimensions of type B nozzle are shown in Figure 2 and Table 2.D2
Table 2 Dimensions QiuWww.bzxZ.net
Nominal pressure PN
Nominal true diameter
Reference weight
WW.bzsOso.comNominal E force PN
Nominal diameter
3.3 Marking example
HG/T 2143-91
Continued 2
Glass equipment A nozzle, nominal pressure PN1.0MPa, nominal diameter DN100mm marking: nozzle PN1,0 DN100-A HG/T 2143-914 Technical requirements
4.1 The pipe door shall be selected, manufactured, tested and accepted in accordance with ZG94004 and this standard T
Reference quantity
4.2 The pipe mouth shall not have delamination, cracks, non-metallic inclusions and other defects that can reduce the strength of the pipe mouth and affect the quality of the glass. 4.3 b in the table is the minimum thickness of the pipe mouth. When making, it must match the thickness of the corresponding top hole and interface to ensure the quality of the butt weld. 5: Packaging, transportation and storage
5.1 The surface of the glass must be prevented from collision to ensure the requirements of the opposite side of the glass. 5.2 The product should be accompanied by a packaging list, Product certificate and product instructions, 5.3 Products should be stored indoors, open-air storage or stacking is not allowed, additional notes:
This standard is proposed by Zhongsui Chemical Equipment Corporation. This standard is under the jurisdiction of the National Standardization Technical Committee for Glass Equipment. This standard was drafted by the Shanghai Pharmaceutical Design Institute of the State Drug Administration. The main drafters of this standard are Hua Qiuyuan, Li Yijun and Bao Aiyuan. This standard refers to the German national standard DIN28159-1983 "Pipes for Glass Containers". From the date of implementation of this standard, the former Ministry of Chemical Industry's standard HG5-261~79 "Pipes for Glass Equipment" will be invalid.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.