title>Particle size analysis - Laser diffraction methods - Part 1: General principles - GB/T 19077.1-2008 - Chinese standardNet - bzxz.net
Home > GB > Particle size analysis - Laser diffraction methods - Part 1: General principles
Particle size analysis - Laser diffraction methods - Part 1: General principles

Basic Information

Standard ID: GB/T 19077.1-2008

Standard Name:Particle size analysis - Laser diffraction methods - Part 1: General principles

Chinese Name: 粒度分析 激光衍射法 第1部分:通则

Standard category:National Standard (GB)

state:Abolished

Date of Release2008-04-16

Date of Implementation:2008-10-01

Date of Expiration:2016-06-01

standard classification number

Standard ICS number:Test >> 19.120 Particle size analysis, screening

Standard Classification Number:General>>Basic Standards>>A28 Screening, Screen Plates and Screen Meshes

associated standards

alternative situation:Replaces GB/T 19077.1-2003

Procurement status:IDT ISO 13320-1:1999

Publication information

publishing house:China Standards Press

ISBN:155066·1-31688

Plan number:20030759-T-469

Publication date:2008-06-01

other information

Release date:2003-04-15

drafter:Zhang Xunbiao, Lu Desheng, Liao Zongting, Zhou Jianxiong, Yang Qing, Yu Fang, Liu Fen, Deng Baoqing, Li Rong

Drafting unit:Tongji University, Institute of Geology and Geophysics, Chinese Academy of Sciences, Shanghai Institute of Metrology and Measurement Technology, Institute of Chemistry, Chinese Academy of Sciences

Focal point unit:National Technical Committee for Standardization of Sieve Screening and Particle Sorting Methods

Proposing unit:National Technical Committee for Standardization of Sieve Screening and Particle Sorting Methods

Publishing department:General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China

competent authority:National Standardization Administration

Introduction to standards:

This part of GB/T 19077.1 specifies the determination of the particle size distribution of a two-phase particle system by analyzing the angular distribution scattering diagram of light. This part is applicable to the determination of bubbles in powders, sprays, smoke, aerosols, emulsions and liquids. No specific requirements are made for the determination of particle size by specific instruments. The particle size range applicable to this part is from about 0.1 μm to 3 mm. GB/T 19077.1-2008 Particle size analysis by laser diffraction method Part 1: General GB/T19077.1-2008 Standard download decompression password: www.bzxz.net
This part of GB/T 19077.1 specifies the determination of the particle size distribution of a two-phase particle system by analyzing the angular distribution scattering diagram of light. This part is applicable to the determination of bubbles in powders, sprays, smoke, aerosols, emulsions and liquids. No specific requirements are made for the determination of particle size by specific instruments. This part is applicable to the particle size range from about 0.1 μm to 3 mm.
class="f14" style="padding-top:10px; padding-left:12px; padding-bottom:10px;"> GB/T 19077 "Laser diffraction method for particle size analysis" is divided into the following two parts:
--- Part 1: General principles;
--- Part 2: Validation of the reversal procedure. This part
is the first part of GB/T 19077.
This part is equivalent to ISO 13320-1:1999 "Laser diffraction method for particle size analysis Part 1: General principles" (English version).
For ease of use, this part has been modified as follows:
--- This international standard has been changed to this part;
--- The foreword of the international standard has been deleted;
--- The comma, which is used as a decimal point, has been replaced by a decimal point.
This part replaces GB/T 19077.1-2003 “Laser diffraction method for particle size analysis”.
Compared with GB/T 19077.1-2003, the main changes in this part are as follows:
--- GB/T 19077.1-2003 has been modified to adopt ISO 13320-1:1999 and changed to adopt ISO 13320-1:1999 equivalently.
--- Figure 3b of GB/T 19077.1-2003 has been modified.
--- The contents added to the table of refractive index of solids have been deleted.
---Delete the last part of the introduction. Some equipment can measure down to 0.02μm.
---Modify the expression of some contents.
Appendix A to Appendix D of this part are all informative appendices.
This part is proposed and managed by the National Technical Committee for Standardization of Screen Screening and Particle Sorting Methods.
Drafting units of this part: Tongji University, Institute of Mineral Resources, Chinese Academy of Geological Sciences, Shanghai Institute of Science and Technology Information, China Machinery Productivity Promotion Center, Institute of Chemistry, Chinese Academy of Sciences, Shanghai University of Technology, etc.
Main drafters of this part: Zhang Xunbiao, Lu Desheng, Liao Zongting, Zhou Jianxiong, Yang Qing, Yu Fang, Liu Fen, Deng Baoqing, Li Rong, etc. The
previous versions of the standards replaced by this part are:
---GB/T19077.1-2003.
The clauses in the following documents become clauses of this part through reference in this part of GB/T 19077. For all dated referenced documents, all subsequent amendments (excluding errata) or revisions are not applicable to this part. However, parties to agreements based on this part are encouraged to study whether the latest versions of these documents can be used. For all undated referenced documents, the latest versions are applicable to this part.
GB/T15445-1995 Graphical representation of particle size analysis results (ISO92761:1990, neq)
Foreword III
Introduction IV
1 Scope 1
2 Normative references 1
3 Terms, definitions and symbols 1
4 Principle 3
5 Laser diffractometer 3
6 Operating procedure 5
6.1 Required conditions 5
6.2 Inspection, preparation, dispersion and concentration of samples 5
6.3 Determination 7
6.4 Repeatability 8
6.5 Accuracy 8
6.6 Sources and analysis of errors 9
6.7 Resolution and sensitivity 10
7 Analysis Report 10
Appendix A (Informative Appendix) Theoretical Basis of Laser Diffraction 12
Appendix B (Informative Appendix) Suggestions on the Contents of the Instrument Manual 18
Appendix C (Informative Appendix) Dispersions for Laser Diffraction Methods 20
Appendix D (Informative Appendix) Refractive Indices of Various Liquids and Solids 21

Some standard content:

ICS19.120
National Standard of the People's Republic of China
GB/T19077.1—2008/ISO13320-1:1999 replaces GB/T19077.1-2003
Particle size analysis
Laser diffraction methods
Part 1: General
Particle size analysis-Laser diffraction methods-Part 1: General principles
(ISO13320-11999, IDT)
2008-04-16 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China
Digital anti-counterfeiting
2008-10-01 Implementation
1Bawei
Normative references
Basic definitions and symbols
Most popular To the proposal
The order of the work
Please provide the conditions
Sample inspection, preparation, scoring and assembly
Repeatability
Approval
The arrival and distribution
Analysis report
Appendix A (Informative Appendix) Theoretical and theoretical information of laser radiation
Appendix B (Informative Appendix)
Appendix ( Appendix D (Appendix D) of the method for the distribution of optical radiation of various materials: Appendix D (Appendix D) Refractive index of various materials: CB/T19077.1-2008/IS013320-1:19993, GB/T19077.1-2006/IS013320-1:1999GT190 The optical radiation is divided into the following categories: Through the room |2 points, reverse the visual order,
This part is the first part of GE/T1307T
This part number can be adopted as [5013320-1:1 Light analysis method Part 1, English version 3), for the purpose of use, the following scientific adjustments have been made: "This international standard" is changed to "this part", except for the use of period, instead of the forward sign as the decimal point *, this part represents GB/T1307?.1-20036 Light analysis method 3, this part is consistent with GD7. The changes to the 200-level file are as follows: GB/T19109712033 is modified to use 15013320-11999, and is changed to 15013320-1.1999 format. The GB/T1Som.1cs Figure 3b) is changed. The content of the foreign refractive index table is added, and the last part of the introduction has a disk equipment reading limit of 0C2m. The content of some contents is also added. This part is recorded in the first time for the health check and service service. This part is issued by the National Chemical Engineering Committee and the import and export, and the drafting units of this part are Tongji University, Central Academy of Sciences, Shanghai Institute of Information Technology, Institute of Rural Productivity Di Center, and Shanghai University of Technology. The main characters of this article are: Zhang Xunjie, Chan Deniu, Jia Zongyan, Ri Daofeng, Weixiao, Yu Fang, Liu Fen, Deng Baoqing, Li Shi, etc. The standard of this article is: GB/T190Y2.1-2303,
, ma specializes in Beixi Shengmu
GB/T19077.1-2008/1S013320-1-1999 cited
Since the previous Jingguang title For the public, you have not been widely used in many fields. The success of this technology lies in its ability to treat various non-optical particle systems, and it can be used in commercial devices such as self-service and home appliances. Only the positive angle of the device can be used. The positive angle of the result needs to be carefully avoided. Therefore, it is necessary to establish an international standard for the use of the wrong light, and provide a new method for controlling the quality of the particles.
Wansheng straight, the most low-angle light technology is released, so it is more than the flying king's other name: Dashuang and Guiyu:
Recently, the ancient light
low-angle micro-light
knows that the wave report technology has been used to protect the current period.
Zhang Guangrun Finance Technology
In addition to the theory of using the micro-Ming to sue, the social guard street life is opening up normal duties, and the random distribution of the shooting should be recognized in the autumn of this person. The existing phenomenon of the joint teaching in the economy will
male dare to shoot the ability of the trapped, do the light of the natural mother, just replace the change of small troubles control is only the teacher assumes that the particle is the shape of
buy 1 bean music single
is a person's dry big and the store's quality of the country's shape of half of the shape of the skin of the medical shape of half of the name
under certain conditions, the detailed micro-time use of Ni Xue Bao anti-release time of the country's stacking red, the method of show every decoction uses accurate registration mouse unit body is the love of light to do the shooting wind shape, report to Ma Shi's picture! It is more in line with the good shape of the calculation out of the ice breath plus the shift sequence, so that the lunar optical time
longitude distribution has (reference station
beautiful your micro north mouth from the east twist has the free system of gra points to conquer, formulate the number of first make the distribution of the operator, controller and calculate the pad skin distribution of the opening organic channel,
this is the street shooting to find the technology you don't know the female this limit control of the topic shooting, or to have the number of integration to dare to shoot, call data included in the multi-effect sample sound selection leisure topic
creative skin group of granularity after the physical heart
some can form the image of the original city to collect more points cloth
cloth·in the city's full limit material group can become a state-owned policy school students' particle size distribution has
relatively, we are concerned about the original eater
Figure 1 two spherical summer teaching to do the shooting group to produce the relatively large diameter is to produce the net b) of the particles light 2 use the previous only device, usually can only use less than 1 loose steel urgent, so that the double to the teaching disgust less than 1 day of use, its wind garden is, people's free measurement of the small assistant teaching sense of shooting the most obvious difference is (meeting the people's tea A), many modern only devices, can be measured to the largest change of shooting, this to 150 Xin right, as through the meeting is happy By using more or larger beams or more detections, the average person can be measured to a small new secret of 01, and the intensity of the recording device can be different at different wavelengths. By using this air-to-air breath, the idea of ​​improving the interaction can be completed, and the particle size, ma#: Line Beixianshengmu
GB/T190/71-2038/1901332C-1:1995 Particle size analysis - Laser diffraction method - Part 1 - General rules GB 12077 This part now defines This part is also suitable for the angular distribution of light, and is used to determine the angular distribution of loose bodies, smoke, gas, glue, bubbles in emulsions, etc. It does not have a specific effect on the specific device. The applicable range of this method is from about 3.1m-amm. The design technology is set as the glue shape class light, so the shape distribution obtained is the result of the relevant particle size distribution, and it can be determined regardless of the other materials (specific antibody method, section classification method). 2. The following clauses are incorporated herein by reference and form a part of this contract. All subsequent revisions or amendments to this document, including those not dated, are not applicable to this part. For the purpose of research, the latest version of these documents shall apply. For any document not dated, the latest version shall apply to this part, GB/T1E4451995 Item Size Specification Graphical Specification (1SO9275-1, 1990, neq) 3. Technical Cases, Definitions and Reference Numbers The following terms are defined in the technical specifications. 3.1 Terms and Definitions The latest version shall apply to this part. 3.1.2
coefficient of variation of the standard deviation divided by the mean: 0.0, equivalent to the standard deviation (for a normal distribution, the median is equal to the mean), 3.1.3
complex refractive index complexrefractiveindex is the ratio of the complex refractive index of the particle to the refractive index of the medium, m-N, 3.1.4
relative refractive index relative refractive index is the ratio of the complex refractive index of the particle to the refractive index of the medium, m-N, 3.1.5
derived national folding method
deennvnlutiean
reported that the measurement of the radiation map is the value of the inference product group love distribution mathematical procedure 3.1.6
radiation diffraetion
light Limon high straight line propagation and then through the projection edge of the phenomenon 5.1.7
chicken light exrinetinn
light to see the left middle through the visual absorption phenomenon and the world radiation market decline confusion of the present home 1
, ma special line north wash rise animal husbandry
GR/T 19077.1-2308/IS013320-119993.1.8
Change type mudelmalix
From the calculation of the family type, the package unit of the milk is obtained with chaos, abandonment and size. The light loss and composition of the model are certain. L's shape of the measuring device cannot be expressed in terms of matrix,
multiple radiation multiplescattering
micro light to dare to time and single, and single model is different, its sensitivity is not all single radiation map you add, 3.1.13||tt ||Total bottom/optical concentration uluseuration, opticaltoncrntentlon due to the relatively small yet no teeth feeding people radiation allowable load change baby percentage caused 3.1.11
optical chess type npticalmud
and physical model, passband
such as: large electric zero help radiation, rising market
friend radiation rellestian
qing Europe seal
issue purchase optical technology 0
back to this long inevitable match
fold ef rac
just from a
nsing-n,sin
people male·rush medium wind auxiliary speed seat and monk cavitation phenomenon you it in Soa law,E
to retreat to two and,the interface changes the transmission pressure between the total dynamic S
number resistant medical
altern
by丨doing the shooting can produce
degree use more I learn Shangcai this figure girl first hand snack An connect old this creative olive detector unit series good version degree surface natural energy
single dare music siauke seann
new La group in a single teaching natural energy time shooting figure quality teaching refers to the mutual independent industry dare to buy 3.1.17
with ofndrmalsasdisrribnttan normal distribution of the home
standard storage total (natural relative value) war open oxygen number (relative percentage, for ten points have a large total of the welcome to a uniform situation plus the standard thank you is within the large total of 9.7 natural value plus or minus times the standard deviation. 3.2 symbol
particle model precursor disorder health: element:
distance from the environment, mm;
KD precision wheel before the angular distribution of intensity (scattered plan):) measurement unit, nest of the radiation close to the scientific distribution (The micro-radiograph also shows the monitoring of the complex radiation:
medical measurement # single photoelectric range, uA
change number 20/person
, ma#: line north first rise animal husbandry
4 principle
Xia La refraction car health effect (absorption) part: no black radiation contains the length of the teaching east m
photoelectric first quantity)
more pull the relative complex refractive index of the medium
medium resistance to the actual part of the car
pre-particle folding to the actual part of the signature
particle natural refraction car
you! The result is when the girl points to the meat!
the reading of the particles in the industrial disperser!
the diameter of the concentration!
GB/T19C771-2008/1S013320-1:1996 poly in the diameter of the flower, accounting for the total secret 5 must teach the straight symbol of the small ten this person value, there is also the total fee 50 music auxiliary soft standing person this cautious,
accounting for the total car steel teeth of the problem is relatively straight move small thousand this value, small! Accounting for the total cost of the system of the yuan of the estimated value of relatively straight eighty this value,! Infinite continent of the scale of the hair more caused,
teaching shooting has photography scholars than the city to come - the big model can shoot bone! The piece of the certificate in the bundle and the world also the law between the real people see the thousand hit the Sne fixed mind: the black disease in the boundless and the world the law between the real book to the e fixed god model light car medium such as liquid or gas with milk, the respect of the long day! After obtaining a representative sample of the size in the dry film, it is separated in a suitable medium or gas with appropriate equipment, and a monochromatic beam (more often a laser) is passed through it. The light is pre-scattered and distributed at different points. A regular multi-element detector receives the corresponding values ​​at these multiple points and records the values. Using appropriate optical models and mathematical procedures, the point numbers are calculated to obtain the ratio of the volume of the sample at each degree to the total volume, thereby obtaining the particle size distribution. As for the light-drinking
real health and light-protection only, the concept is shown in Figure 2. There is no strong home beauty product:
micro-Keran,
through the radiation to
time civilization to make hot
card video to make 1 to project your internal radiation:
light into the Kangyuan,
selection, work with funds,
East without,
delivery 4 of the pre-electric,
Figure 2 common type of combined light radiation instrument structure diagram
a line flow rise animal husbandry
GB/T1937712008/1801 3320-11999 This is the most regular structure of the light, the light mouse (a glue is a light emitting) is transported through the subsequent beam of light class, the phase, half of the light ball, the normal light chain development, the need to gather, pass, expand the most close to the girl's light to form a single particle, there is a representative of the sample of the British most Maid added original hall, for the transmission of the individual fluid or gas) through the measuring area of ​​the light, this measuring area is effectively working,
there is a representative of the moon song light page direct technology to sit the most real measurement, such as the night guest, the gas content and the bubble in the body of the glue. , in addition, the whole sample is added with porous liquid, soft objects and objects, etc.), and can be separated in an appropriate amount (see the attached test, the separation requires maintenance) and the machine is pulled and sounded) or both are used together to separate and form a stable separation state. For this system, please use a ring system. This system is an optical mass spectrometer with a separator and an ultrasonic generator. The system and the special powder separator are used. The machine is used to separate the powders. The shape of the sample is the most polite, and there is a certain way to give the sample a certain delivery path. The separator uses compressed gas or vacuum card The quality of the beautiful particles is acid and particles, and the gas will be divided into cavities by the instrument. The gas will be used to make the huge amount of evidence. There are two ways to make the particles enter the light zone. The forbidden way is to guide the light beam into the front of the light energy zone. The auxiliary light beam will be focused behind the light environment. See Figure 35. The light is small. The disk is rusty. The leaves are carefully: The art group is taller than the workers. The way to enter the world is more effective. You can drink the light! The sky is generally shot: tt||3 bottles of pine. The protective clothing is connected to the road environment and the report group will come between the car! Figure 3 shows the structure of the improved light radiation instrument with the particle delivery method. The method is to create a worry in the effective working range of the selected energy, allowing the evaluation to have a wide sensitive time zone. The first method has a certain amount of medical control time for the wide virtual space before the single shot can be sheared to a large angle of the self-release time, and the dosage is not effective. The first method is mainly used for the protection method. If the light path is reasonably designed, the jet flow can also be thrown away. The light composition is relatively good after the test, and the color is not strong at the angle of the new round (see time A). Therefore, the shot is ma Qixing Beixian Shengmu
CB/T19077.1-2008/1S013320-1.1593 North and micro-light years into the total for the strong use of points, promise a mouth I please or Zhi suitable mirror I system image focal creation more children control general, to feel the political cause, on the fixed range of jade, the style of the country and the purchase of the light beam in the package and has nothing to do with, continuous light war free distribution 1 (, in the multi-dimensional food if the whole into a person continuous step multi-space distribution within the limit set record moment of the table home like intention time doctor, with all acid machine position two, the single cost of the sum of the shooting saint is relative, note: I have the risk of doing the shadow angle within the dare to shoot light, can encourage the selection To collect data, the detector is usually composed of a large number of main diodes. There is only one diode that is combined with a moving diode. The photodiode converts the light intensity in the space into a series of photocurrents (,). Then, the photoelectric circuit is amplified and digitally converted into a quantity of energy. According to this, the central unit is used to determine the appropriate light intensity. This degree can be used to calculate the optical quality! , there is only a set of central unit with a special set of mobile detection to create a positioning device, this detection unit is used for storage and calculation, the computer can control the instrument automatically, store the signal received by the operator, and use the optical control type. It contains a single body to provide a medium-level light quantity, the detection training system can be seen, the calculation of the degree of maintenance (see Appendix 3. The theoretical basis of laser emission), of course, also provides the automatic operation of the relevant instrument, from different manufacturers! The key codes and software of the same manufacturer with different numbers are naturally different. The specific transmitter needs to have enough accurate information to distinguish the differences. In the actual use of the neutral light emission book, the neutral light emission data is only used. 6 Working procedures
6.1 Required conditions
G.1.1 The device should be installed in a clean place with low voltage, low mechanical disturbance, low smog, and out of direct sunlight. The working area should have good ventilation. It is recommended to work on a natural optical table. The cabinet can be placed on a dry surface. The optical system will not be exposed to heavy objects such as dust.
Warning: The device should only have a low-power light source to avoid prolonged damage. Do not look at direct light or reflected light. Do not use reflective surfaces. Local radiation safety regulations should be observed. 6.1.2 The dispersant of this body is known. Various dispersants can be used as dispersants for powders. The dispersant of the body must be resistant to ℃. If a certain dispersant is used as a dispersant, it is necessary to observe the health and safety standards of the department. When using evaporable fluids, it is necessary to use ultrasonic waves inside the skin. Dangerous gas will accumulate above the surface or due to the development of the body, the health of the skin will be low, and the effect of the depth change will be reduced.
613 The gas used in the dispersant should be used to prevent common When performing the analysis, if compressed gas is used, the gas cannot contain normal particles. Any vacuum equipment should be separated from the measurement area to prevent the air it outputs from entering the measurement area. The changes in temperature caused by the intake air should be observed according to the standard. 5.2 Sample inspection, preparation, analysis and temperature 5.2.1 Visual or recorded inspection, comparison of the temperature and shape of the product, as well as the relevant test results, if accompanied by products! 5.2.2 Sample preparation For good ice cream, the sample preparation technology should be: add the light agent fully, and at the same time use a spatula to mix it. If the mixture is lost, the high agent should be added and baked. If the mixture is not lost, the high agent should be added and baked. GB/T19077.1-2308/1S013320-1,1999, the mixing agent should be added. If the mixture is not lost, the high agent should be added and baked. GB/T19077.1-2308/1S013320-1,1999, the mixing agent should be added. If there is a blue end teaching product in the ancient Zhao out of the United States standard country, the determination I read the particles out of the tour, you can use a simple division, but choose the current determination to remember to ask the husband to remove some of the teaching ratio,
because, for pounds of fog, gas and other senses and children with the application of the gas tour, when sampling encounter light, do not receive the change of the needle cloth, it is almost impossible, so, only the dream time is appropriate (see .2.36.2. Clause should be directly measured according to the sleep service 6.2.3 sample division
5.2.31 under the division of the body to use gas or this rest division, the division of the rubber seat is in line with the day of the completion of the lead, for example: is the determination of the original single particle, also mutual determination of the reunion of the skin after the auxiliary teaching
6.2.3.2 operation with a very suitable release, generally is the fast moon jade air or the real car for division, it tries to throw more cutting force and frequency with the ticket between, The onboard documents of the collected samples are combined with the public documents of the road collection. For the dry powder distribution, it is noted that the samples with the characteristics of the products have the characteristics of the representative products. In order to create a lighter and wider nuclear separation, it is necessary to use the smallest number of particles and the largest reading. The sample has a certain amount of blood. For the determination of the amount of blood, the original light distribution of the sample should be determined. The distribution rate should be properly dispersed. The particle size distribution is relatively large. Usually, the dry powder distribution result is directly compared with the body dispersion result. The result is the same. Another method is to change the distribution energy (the original gas pressure), the particle size distribution change is usually increased, and the distribution energy is increased. After the distribution is determined, the low distribution rate is not affected, and the energy is increased. And the small particles increase, the midpoint of incomplete stability is the most appropriate measurement value. Note that instability does not necessarily occur (addition is the result of reaggregation or disorder). The use of selected scientific cutting village introduction leads to the process of very scattered particles. I must avoid it. 6.2.5.3 Bamboo multi-child body can be used as a large separation agent. The conditions required are as follows. Both the test and the test results will promote the separation of the fluid. The effect of the separation can be observed by the imaging system. The test can be used to quantify the suspension only. At the same time, use appropriate protective drugs: if the sample is fully separated, the slight distribution obtained by adding children should not be empty. In order to create reliable results, the minimum sample volume is required. As the separation is done The larger the size of the country, the more accurate the response needs to be. For example, the dosage form must be adjusted according to the dosage form, and the area of ​​the sample must be the largest. For example, the sugar content of the product is preferably 2mL--20mL. At least 0.3mL of sample is required, and at least 500mL of the sample is required. The time required for the sample to be collected or the data of the instrument should be read out at the same time. The concentration of the particles in the sample should not be based on the smallest integer value. For multiple instruments, in order to obtain a signal-to-noise ratio that is slightly less than 5, there is an upper limit on the dosage. In order to avoid multiple exposures (intentional exposure to multiple particles), the value is greater than 20%! About, new smaller than the machine m, the concentration of the world forget the small 15 first, a deep feeling of multiple dare to shoot in my big sensitive corner day. If the night has how much real dare to shoot fast stop, the group of the body measured the release of the model through the real value, if the frequency point training must be determined according to the degree of style, it should be corrected in the release of more camps, the education will exist in the system I said. Figure 5 provides a preliminary calculation of the concentration. The choice of 5 is a good one. It shows the most suitable ratio of the end product to the light skin: small silencer needs low concentration. For example, when the dispersion is crisp, the road length is long, the grain true meal is close to 1, and the street winter true method is close to 0.02%. For 100% of the environment, the body skin should be close to 2%. The measurement results are reported in the book. The width of the pure tensile test city is the most important factor in the sample's natural density. The width of the environmental table is respected according to the world standard. The length of the road in the determination area, the optical properties of the grains, the combined density of the detector unit, etc. are taken into consideration. Thorn, sign in the above factors, for a nail a celebration of the material, in order to determine the most suitable new reference, should be for the non-rolling can cover the right to determine, 6
carry out the light material
body information method can be bright,
body sweet river your boundary
M risk
GB/T19077.1-2008/1SO13323-1:1999at
Figure 5 2mm path length logarithm containing coordinates and pseudo-coordinates of the whole love Gong small and product intention light intelligent radiation points of the black particle filling of the best boundary 6.3 determination
6.3.Procedure
The procedure for using the new distribution of Nandrolone is as follows: Please try the instrument and measure the blue and white
Select the appropriate series of teaching and night-time optical components, perform a blank measurement on the medium without any substance, and store the obtained signal for backup. In the future, when using the thermometer to measure the product, the signal obtained should be the white number. Only when the instrument is used can the real signal of the product be obtained. b) Make a film of the product service map
The most suitable one, only the instrument can be used in the obtained In a short period of time, I got the help of the whole scanning data, specifically 25 scans 13 times, and used the signal of each detection unit to calculate the detection image, and stored it in the computer's memory. The signal of each detection unit can be obtained by taking the accumulated light intensity and conversion effect of the detector, and the coordinates of each detection unit (degrees and position) and the appropriate angle range are determined by the program. All of these are made by the country! , The 3D images of the 1920s and 300s are of very good quality and are not very accurate. The 3D images of the 1920s and 300s are of very good quality and are not very accurate. The 3D images of the 1920s and 300s are of very good quality and are not very accurate. The 3D images of the 1920s and 300s are of very good quality and are not very accurate. The 3D images of the 1920s and 300s are of very good quality and are not very accurate. The 3D images of the 1920s and 300s are of very good quality and are not very accurate. The eating position must be useful, and the dream of the whole distribution of fresh and new scenes is the inverted type. The exploration of the evil dares to calculate the parameters of the grain. In fact, there is always a sense of speed difference in the mouse topography. The slight distribution of the results of the possible production of the station is stored in the sequence of the whole bean hair quality. In different settings, medical use is obtained. They include: the weighted simple difference of the measured continuous gas calculation value such as: the least square, a first Yang control condition such as: the total knowledge of the grain is not urged to teach and you are in the main distribution of the self-clear difference, you can use a new group sequence monitoring health special health signal of the woman, introduce more when the network light object
GB/T19073.1-2008/1S013320-1:199 3's teaching scan weighted, and ear acupuncture particle distribution uncertainty, 5.3.2 Note the previous item
beauty during any time period of the division should be nuclear membrane cat drink filial piety hand model creation related instructions, also exceed the following matters to pay attention to) before turning on the power to change the shear, the device should be confirmed that all parts of the existing grounding, all Gu Pull model and pin delivery device, friendly Bai device host, ten points to do the road, vacuum inlet and vacuum channel should be grounded to prevent the main language electrical equipment from igniting the organic chain thorns of the whole device,
press power on, the industry is equal to enough time to make the drinker predetermined, the gas light (plan LleNe dare light elegant) model width more than half an hour of heating time,
pull only the state of the device, if needed, should identify the whole beauty determination fan Xian and product, the wine through observation detection mark The purple auxiliary recognition lock is in good condition, and the dry position I lead the inspection on the old, no need for particles, for a certain benefit, the receiver and the points can be done by me, the specific store boundary is pleasant, whether the plan is European and the position is registered, the optical parts are cleaned during the baby, to ensure that the signal from the back account is lower than the micro-|tt|| within the specific working distance, all the texts need to be done with the radiation, and the equipment is tested by the normal
theft can be gathered in the gift to get 1 (a kind of daily skin-free exchange list) in order to ensure semi-precision and health, the purchase is done monthly and the standard # product calibration has been written in (Bei 64 and 6.5.2) many anti-epidemic companies do the installation in the presence of gas, skin-free use micro-ball test for the improvement of the score
) for the dry points I you and the subsequent pursuit is to forget the cow's fixed service education.
release equipment certification implementation
for ten gas air development benefits practical learning, confirm I have a book representative of the irradiation play doubt to develop the most special benefits of people, take or nourish the movement of the average hook domain into the human state station
such as Wu Ke
steal optics surprise twist has beautiful discount time rate for teaching variation new results national film, comfortable product for multi-effect teaching degree kid m
car this you material process people open course have been small product meat, will be greater than the limit of the period said large (Annex to the research: test wake up clean fruit
9.4 repeatability
13 samples celebrate a batch of average learning
for ten particle size points is higher than the system effect is not in the natural or auxiliary teaching big The ratio of the small light to the median of the distribution, the coefficient of variation is 5 times taken from the small sample, the characteristic measurement is as follows
I do not want to interfere with the frequency, the industry variance is 3%, for the value of the teaching component, for example
the number can be borrowed
6.5 accuracy
6.5. The laser intelligent injection system is based on pregnancy (see Appendix A, so the production format is more meaningful, but the use of infants needs to be rushed to the academic verification of the selection of each
85.2 strong people
E.5.2, 1 use a few meal numbers or any self-standard certificate of the international standard purchase can be played by everyone In order to change the calibration, the entire determination sequence must be checked, including the sample, sample analysis, sample selection, adjustment, and all other procedures. This card has made sufficient comments on the operation sequence.
The plastic love announced that the material has a certificate of full absorption, and its ball and purchase should have more than 10 softness models. These standard materials need to use the listed methods to forget the resistance of various virtual and other fields. The analysis should have a practical and detailed operation. If the theory is used for calculation, the disk can use the low multiple discount of the material. The precision of the consumption position, for the state according to the length of the quality or the certificate of the benefit of at least 3 people to buy the determination, the average value of the standard value is obtained. The standard is that the average value is less than 3 and the standard value is less than 5. Although it is better to use pregnant women, non-invasive tests can be used, preferably with a certificate or medical certificate, and with the corresponding progress and allowance for the new course. If other methods other than invasive surgery are used, it may produce! It is not very stable, and the original class cannot be changed. Different teeth have different spiritual attention to the frequency of light, so for the same non-invasive test, it is possible to get different effects.
Feng: Netn Special Line Non-Washing and Shepherd2. Note the above items. The teacher should check the relevant instructions during the analysis and analysis period. Also pay attention to the following matters: before turning on the power, all parts of the device should be grounded well, all the distribution devices and delivery devices, the device should be grounded, the vacuum air inlet and the vacuum channel should be grounded to prevent the main electrical equipment from igniting the whole device. After turning on the power, the time is enough to make the device predetermined. The gas light (plan LleNe dare light Ya) channel width is more than half an hour to cause heat. The device is only in a state of sinking. If necessary, the whole device should be identified and the product should be inspected. The purple auxiliary lock on the detection mark should be observed and confirmed to be in good condition. I lead the inspection on the old position, there is no need for particles, for a certain benefit, we can receive and divide the equipment of each of us, the specific store boundary is pleasant, whether the plan is European and the position must be registered, the optical parts must be cleaned during the baby's work, in order to ensure that the signal from the back of the account is lower than the micro-|tt|| within the specific working distance, all the documents must be done in the light, and the equipment must be tested regularly
and the theft can be gathered in the gift to get 1 (a kind of daily skin-free exchange list) in order to ensure semi-precision and sexual health, the purchase of monthly selected products has been written in the standard # product calibration (Bei 64 and 6.5.2) and there are many anti-gas in the equipment, skin-free use micro-ball test for the improvement of the score
) for the dry points I you and the subsequent pursuit is to forget the cow's fixed service education.
release equipment certification implementation
for ten gas air development benefits practical learning, confirm I have a book representative of the irradiation play doubt to develop the most special benefits of people, take or nourish the movement of the average hook domain into the human state station
such as Wu Ke
steal optics surprise twist has beautiful discount time rate for teaching variation new results national film, comfortable product for multi-effect teaching degree kid m
car this you material process people open course have been small product meat, will be greater than the limit of the period said large (Annex to the research: test wake up clean fruit
9.4 repeatability
13 samples celebrate a batch of average learning
for ten particle size points is higher than the system effect is not in the natural or auxiliary teaching big The ratio of the small light to the median of the distribution, the coefficient of variation is 5 times taken from the small sample, the characteristic measurement is as follows
I do not want to interfere with the frequency, the industry variance is 3%, for the value of the teaching component, for example
the number can be borrowed
6.5 accuracy
6.5. The laser intelligent injection system is based on pregnancy (see Appendix A, so the production format is more meaningful, but the use of infants needs to be rushed to the academic verification of the selection of each
85.2 strong people
E.5.2, 1 use a few meal numbers or any self-standard certificate of the international standard purchase can be played by everyone In order to change the calibration, the entire determination sequence must be checked, including the sample, sample analysis, sample selection, adjustment, and all other procedures. This card has made sufficient comments on the operation sequence.
The plastic love announced that the material has a certificate of full absorption, and its ball and purchase should have more than 10 softness models. These standard materials need to use the listed methods to forget the resistance of various virtual and other fields. The analysis should have a practical and detailed operation. If the theory is used for calculation, the disk can use the low multiple discount of the material. The precision of the consumption position, for the state according to the length of the quality or the certificate of the benefit of at least 3 people to buy the determination, the average value of the standard value is obtained. The standard is that the average value is less than 3 and the standard value is less than 5. Although it is better to use pregnant women, non-invasive tests can be used, preferably with a certificate or medical certificate, and with the corresponding progress and allowance for the new course. If other methods other than invasive surgery are used, it may produce! It is not very stable, and the original class cannot be changed. Different teeth have different spiritual attention to the frequency of light, so for the same non-invasive test, it is possible to get different effects.
Feng: Netn Special Line Non-Washing and Shepherd2. Note the above items. The teacher should check the relevant instructions during the analysis and analysis period. Also pay attention to the following matters: before turning on the power, all parts of the device should be grounded well, all the distribution devices and delivery devices, the device should be grounded, the vacuum air inlet and the vacuum channel should be grounded to prevent the main electrical equipment from igniting the whole device. After turning on the power, the time is enough to make the device predetermined. The gas light (plan LleNe dare light Ya) channel width is more than half an hour to cause heat. The device is only in a state of sinking. If necessary, the whole device should be identified and the product should be inspected. The purple auxiliary lock on the detection mark should be observed and confirmed to be in good condition. I lead the inspection on the old position, there is no need for particles, for a certain benefit, we can receive and divide the equipment of each of us, the specific store boundary is pleasant, whether the plan is European and the position must be registered, the optical parts must be cleaned during the baby's work, in order to ensure that the signal from the back of the account is lower than the micro-|tt|| within the specific working distance, all the documents must be done in the light, and the equipment must be tested regularly
and the theft can be gathered in the gift to get 1 (a kind of daily skin-free exchange list) in order to ensure semi-precision and sexual health, the purchase of monthly selected products has been written in the standard # product calibration (Bei 64 and 6.5.2) and there are many anti-gas in the equipment, skin-free use micro-ball test for the improvement of the score
) for the dry points I you and the subsequent pursuit is to forget the cow's fixed service education.
release equipment certification implementation
for ten gas air development benefits practical learning, confirm I have a book representative of the irradiation play doubt to develop the most special benefits of people, take or nourish the movement of the average hook domain into the human state station
such as Wu Ke
steal optics surprise twist has beautiful discount time rate for teaching variation new results national film, comfortable product for multi-effect teaching degree kid m
car this you material process people open course have been small product meat, will be greater than the limit of the period said large (Annex to the research: test wake up clean fruit
9.4 repeatabilitywww.bzxz.net
13 samples celebrate a batch of average learning
for ten particle size points is higher than the system effect is not in the natural or auxiliary teaching big The ratio of the small light to the median of the distribution, the coefficient of variation is 5 times taken from the small sample, the characteristic measurement is as follows
I do not want to interfere with the frequency, the industry variance is 3%, for the value of the teaching component, for example
the number can be borrowed
6.5 accuracy
6.5. The laser intelligent injection system is based on pregnancy (see Appendix A, so the production format is more meaningful, but the use of infants needs to be rushed to the academic verification of the selection of each
85.2 strong people
E.5.2, 1 use a few meal numbers or any self-standard certificate of the international standard purchase can be played by everyone In order to change the calibration, the entire determination sequence must be checked, including the sample, sample analysis, sample selection, adjustment, and all other procedures. This card has made sufficient comments on the operation sequence.
The plastic love announced that the material has a certificate of full absorption, and its ball and purchase should have more than 10 softness models. These standard materials need to use the listed methods to forget the resistance of various virtual and other fields. The analysis should have a practical and detailed operation. If the theory is used for calculation, the disk can use the low multiple discount of the material. The precision of the consumption position, for the state according to the length of the quality or the certificate of the benefit of at least 3 people to buy the determination, the average value of the standard value is obtained. The standard is that the average value is less than 3 and the standard value is less than 5. Although it is better to use pregnant women, non-invasive tests can be used, preferably with a certificate or medical certificate, and with the corresponding progress and allowance for the new course. If other methods other than invasive surgery are used, it may produce! It is not very stable, and the original class cannot be changed. Different teeth have different spiritual attention to the frequency of light, so for the same non-invasive test, it is possible to get different effects.
Feng: Netn Special Line Non-Washing and Shepherd
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.