GB/T 30651-2014 Test method for high temperature fluidity of petrolatum anti-corrosion tape GB/T30651-2014 Standard compression package decompression password: www.bzxz.net
This standard specifies the test method, sampling, test steps, results and test report requirements for high temperature fluidity of petrolatum anti-corrosion tape. It is applicable to the test of the adaptability of petrolatum anti-corrosion tape for construction under high temperature.
This standard was drafted in accordance with the rules given in GB/T1.1-2009.
This standard was proposed by China Petroleum and Chemical Industry Federation.
This standard is under the jurisdiction of the National Technical Committee for Anti-Corrosion Standardization (SAC/TC381). This standard
was drafted by: Institute of Oceanology, Chinese Academy of Sciences, China Industrial Anti-Corrosion Technology Association.
The main drafters of this standard.

ICS25.220.99
National Standard of the People's Republic of China
GB/T30651-2014
Test method of fiowability of petrolatum tape at high temperature2014-12-31Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of ChinaStandardization Administration of the People's Republic of China
2015-07-01Implemented
This standard was drafted in accordance with the rules given in GB/T1.12009. This standard was proposed by the China Petroleum and Chemical Industry Federation. This standard is under the jurisdiction of the National Anti-Corrosion Standardization Technical Committee (SAC/TC381). This standard was drafted by the Institute of Oceanology, Chinese Academy of Sciences, and China Industrial Anti-Corrosion Technology Association. GB/T30651—2014
The main drafters of this standard are: Hou Baorong, Wang Jing, Zhao Xia, Yang Lihui, Li Yantao, Li Hongling, Wang Xiutong, Ma Xiumin, Cao Kun, Sun Congtao, Wang Hao, Gao Yang.
1 Scope
Test method for high temperature fluidity of petrolatum anti-corrosion tape GB/T30651-2014
This standard specifies the requirements for instruments, equipment, sampling, test steps, results and test reports for the test method for high temperature fluidity of petrolatum anti-corrosion tape.
This standard is applicable to the test of the construction adaptability of petrolatum anti-corrosion tape under the ambient temperature range of 45~65℃. 2 Terms and definitions
The following terms and definitions apply to this document. 2.1
Petrolatum anti-corrosion tape
Petrolatum tape
A strip-shaped anti-corrosion material made by dipping non-woven fabric into a special mineral fat containing composite rust inhibitors, corrosion inhibitors, modifiers, lubricants, fillers, etc.
Flowability at high temperature
The performance of the mineral fat anti-corrosion tape after the compound is conditioned for 24 hours under the ambient temperature of 45℃-65℃. 3 Reagents and materials
3.1 Acetone or alcohol: analytical pure
3.2 Steel pipe: 50m in length and 300mm in length.
4 Instrument
Constant temperature drying oven: the range is -20℃～120℃ temperature difference 5 Sampling
Take a mineral fat anti-corrosion tape with a size of 500mm×50mm as a sample. 6 Steps
6.1 Adjust the constant temperature drying oven to keep it at (60±2)℃ or other agreed temperature. 6.2 Use gauze dipped in acetone or ethanol to clean the steel pipe, remove the surface debris, and blow the surface dry. 6.3 Wrap the sample petrolatum anti-corrosion tape twice in the middle of the steel pipe, remove the excess sample, and smooth the surface. 6.4 Place the steel pipe with the sample wrapped on the bracket and place a tray under it, as shown in Figure 1. 6.5 Put the above device as a whole into the constant temperature drying oven with the temperature adjusted, keep it horizontal, and observe whether there is any compound dripping in the tray after 24 hours. 6.6 Perform 3 parallel sample tests at the same time.
GB/T30651-2014
Description:bzxz.net
—Steel pipe:
Petrolatum anti-corrosion tape:
Tray.
7 Result judgment
Figure 1 High temperature fluidity test device
Visually check that there is no composite dripping in the three parallel samples, which means it is qualified, otherwise it is unqualified. Test report
The test report shall at least include the following contents:
Test conditions:
b) Description of the sample, including length, width and thickness; Comparison photos of the sample before and after the test or detailed text description; d) Any differences from the specified test method; Test results and judgment;
Test date;
Tester,
Test location.
riKacanaiKAca-
GB/T30651-2014
Print date: March 23, 2015 F055
People's Republic of China
National Standard
Test method for high temperature fluidity of mineral grease anti-corrosion tape GB/T30651—2014
Published and distributed by China Standards Press
No. 2, Hepingli West Street, Chaoyang District, Beijing (100029) No. 1, Sanlihe North Street, Xicheng District, Beijing No. 6 (100045) Website: spe.net.cn
Editorial Office: (010) 64275323 Distribution Center: (010) 51780235 Reader Service Department: (010) 68523946
Printed by China Standard Press Qinhuangdao Printing Factory Distributed by Xinhua Bookstores in various places
Format 880×12301/16 Printing Sheet 0.5 Word Count 5,000 Words First Edition February 2015 First Printing February 2015 Book Number: 155066·1-50814 Price 14.00 yuan If there is any printing error, the distribution center of our company will replace it. Copyright infringement will be investigated
Report Phone: (010) 68510107
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.