Drafting unit:Equipment Design Technology Center of the Ministry of Chemical Industry
Proposing unit:Chemical Industry Department Equipment Design Technology Center, Chemical Industry Department Chemical Process Piping Design Technology Center
Publishing department:Ministry of Chemical Industry of the People's Republic of China
This standard specifies the type, size, technical requirements and relevant use regulations of loose-fitting steel pipe flanges with butt-welding rings (European system). This standard applies to loose-fitting steel pipe flanges with nominal pressure PNO. 6 MPa (6 bar)-4. 0 MPa (40 bar). The loose-fitting steel pipe flanges specified in this standard are applicable to the two steel pipe outer diameter series n and s specified in HG 20592. HG 20599-1997 Loose-fitting steel pipe flanges with butt-welding rings (European system) HG20599-1997 Standard download decompression password: www.bzxz.net
Some standard content:
Butt-weld ring loose-sleeve steel pipe flange (European system) HG 20599---97 1 Subject content and scope of application This standard specifies the type, size, technical requirements and relevant use regulations of butt-weld ring loose-sleeve steel pipe flange (European system). This standard applies to butt-weld ring loose-sleeve steel pipe flanges with nominal pressure PNo.6MPa (6bar) ~ 4.0MPa (40bar). The butt-weld ring loose-sleeve flanges specified in this standard are applicable to the two steel pipe outer diameter series A and B specified in HG20592, 91 HG20592 HG20603 HG 20604 HG 20605 HG 20613 HG 20614 2. Reference standards Types and parameters of steel pipe flanges (European system)" "Technical conditions for steel pipe flanges (European system)" "Pressure-temperature grades of steel pipe flanges (European system)" "Dimensions of welded joints and grooves of steel pipe flanges (European system)" "Fasteners for steel pipe flanges (European system)" "Selection regulations for steel pipe flanges, gaskets and fasteners (European system)" Flange sealing surface type and applicable scope 3.0.1 The sealing surface type of the flange is raised face (RF). Its size and selection shall comply with the provisions of Chapter 6 and Section 8 of HG20592. 3..2 The applicable pressure and diameter range of the weld ring loose flange shall comply with the provisions of Table 3.0.2. Table 3.0.2 Applicable range Sealing surface type Cool surface ERF) Nominal pressure PN, MPa (har) DN10~600 4 Flange size The size of the flange shall be in accordance with the provisions of Figure 4-1 and Table 4-15. Table 4-1 P No.6MPa (6bar) Butt welding ring loose steel pipe flange Table 4-2 PN1.0MPa (10bar) Butt welding ring loose steel pipe flange Table 4-3 PN1.6MPa (16bar) Butt welding ring loose steel pipe flange Table 4-4 PN2.5MPa (25har) Butt welding ring loose steel pipe flange Table 4-5 PN4.0MPa (40bar) Butt welding ring loose steel pipe flange Butt welding ring neck wall thickness S is generally equal to the nominal thickness of the steel pipe, which is determined by the user. The S values listed in Tables 4-1 to 5 of this standard are only used in situations where the user has not made specific requirements. When the user selects a $ value different from that listed in Table 4-.15, it should be indicated in the order and marking. The flange thickness S of the butt welding ring should not be less than the minimum wall thickness of the steel pipe (0.875S), B, Figure 4-1 Butt welding ring loose sleeve steel pipe flange (PJ (plate loose sleeve)/SE (butt welding ring)) Steel pipe outer diameter (Butt welding ring Neck outer diameter) Table 4-1 PNO.6MP (6har) Butt welding ring loose sleeve copper pipe flange connection size Flange bolt hole Bolt screw Outer diameter center circle 32°100 38:120 45 :130 100:114.3:108 150:168.3:159 426540 450595 Diameter quantity 145139 174165wwW.bzxz.Net 333:334 Butt welding ring Height outer diameter Theoretical weight Butt welding ring Steel pipe outer diameter 【Butt welding ring Table 4—2PN1.0MPa (10bar) butt welding ring loose sleeve steel flange Connection size Flange screw inspection hole bolt bolt Neck outer diameter) Outer diameter center medical 114.3:108 3001323.9 630780 Diameter quantity Flange inner diameter 365386 321416 622642 Butt welding ring Commercial outer diameter Theoretical weight Butt ring Feather tube outer diameter Set 4-3 PN1. 6MPa (16aar) butt welding ring loose sleeve sharp flange connection size (butt welding ring flange bolt hole bolt bolt neck outer diameter> outer diameter center line 1001114.3 108 125;139.7 150f168. 31159[285 200/219.1;219340 3001323.9325 3501335. 6|371 Diameter number Inner diameter of flange 415;435 46714901 5191541 e22,642 Butt welding ring Height outer diameter Theoretical nest Butt ring size 8. 23. 9 8. 0 15. 2 1 55. 8 Nominal outer diameter Table 4-4·PN2. SMPa (25bar) butt welding ring loose sleeve steel pipe flange connection size (butt welding ring thread thread bolt neck outer diameter) outer center 1001114.3 108:235 3771553 diameter base flange inner diameter 120|114 M33×X2 622642 butt welding ring height outer diameter theoretical weight butt welding ring .0. 09 2. 6:2. 6- 0. 17 110·503 8. 0 1 8. 50 609 10.010.0 720[11.011,0 33.4 113, 7 Outer diameter of steel pipe Table 4—SPN4. (MTPz(40bar) Butt welding ring loose sleeve steel pipe flange connection size (Butt welding ring Flange screw gun hole bolt screw control 【Neck outer diameter》Outer diameter center 36 1 33. 71 1001114.31168 :71133 158.31159 480685 631899 Reading diameter type Flange inner diameter Explosion ring Height outer diameter Theoretical weight Tree explosion ring 11. 8i 1. 8. 46 2. 0. 58 1132 11.0111.0 12. 512. 5 73516. 0116. 03 50, E 5 Technical requirements The technical requirements of flanges shall comply with the provisions of HG20603. 6'Maximum non-impact working pressure The nominal pressure of flanges and the maximum non-impact working pressure at different temperatures shall comply with the provisions of HG20604. 7 Welding joints and grooves The dimensions of the welding joints and grooves of the welding ring and the steel pipe shall comply with the provisions of HG20605, 8 Fastener length The length of the fasteners (bolts, studs) used 1 shall comply with the provisions of Appendix A of HG20613. 9 Optional provisions The selection of flanges and gaskets shall comply with the provisions of HG20614, 10 Marking The marking of flanges shall comply with the provisions of HG20592. Additional Notes: This standard proposer, editor and main drafter Proposer: Equipment Design Technology Center of the Ministry of Chemical Industry Chemical Process Piping Design Technology Center of the Ministry of Chemical Industry Editor, Equipment Design Technology Center of the Ministry of Chemical Industry Main drafter: Ying Daoyan Yu Jun Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.