This standard applies to pure niobium plates, strips and foils. GB/T 3630-1983 Niobium plates, strips and foils GB/T3630-1983 Standard download decompression password: www.bzxz.net
Some standard content:
UDC 661.888.2 - 41 National Standard of the People's Republic of China GB3630—83 Sawn sheet, strip and foil Niobium sheet , strip and foil1983-04-16 Issued National Bureau of Standards 1984-02-01 Implementation National Standard of the People's Republic of China Sawn sheet, strip and foil Nlobium sheet, strip and foil This standard applies to pure sawn sheet, strip and foil. Varieties 1.1 The brand, state and specification of the product shall comply with the provisions of Table 1. Table 1 Supply state 0,01 ~ 0,09 Note: (i) In the table, M is soft state and Y is hard state. ② Brand Description: 30~120 50-300 50 - 200 Nhl: Industrial grade pure sawn by vacuum arc or electric beam melting. N: Industrial grade pure sawn by vacuum arc or electron melting. FNbl: Industrial grade pure mixed steel made by powder metallurgy. FNb2: Industrial grade pure steel made by powder metallurgy. ③) The maximum width and length of soft plates and sheets are 200×450mm. 1.2 Dimensions and allowable deviations 100~1000 50-700 60~300 1.2.1 The thickness, width and length of the material and their allowable deviations shall comply with the provisions of Table 2. Issued by the National Bureau of Standards on April 16, 1983 UDC 661.888 .2 - 41 GB3630—83 Strip, plate 1984-02-01 Implementation 0.01~0.02 0.02 ~0. 05 .-0.05 -~0,07 >0. 07 ~0. 09 Thickness tolerance ±0.center04 GB 3630—82 3U ~120 30~120 30 ~120 30 -300 50 300 50-200 60 -200 50~200 50~200 50~200 50-200 50 200 | ~10 [00~10 100-1000 50-700 50~700 50~700 50-600||tt ||50~500 50-300 Length allowable deviation The surface of the foil should be smooth, and inconspicuous waves are allowed, but when rolled on a reel with a diameter of 50-60mm, the waves should be eliminated. The edges of the plates and sheets should be cut neatly and without cracks. 1.a Marking example The plate made of Nbl, M state, first-grade precision, 0.5mm thickness, 200mm width, and 45lmm length is marked as: Plate NblM-grade precision 0.5×200x450mmGB3630-83. 2 Technical requirementsWww.bzxZ.net 2.1 Chemical composition The chemical composition of various grades should comply with the provisions of Table 3. Table 3 Elementary performance Quality content, % Not too high When the company specifies that the mechanical properties of the product are to be measured, the room temperature mechanical properties of the material shall comply with the provisions of Table 4. 2 Nhl, Nh2 FNbl, FNb2 GB 3630—83 Tensile strength wb, kgl/mm? Elongation &, % Note: The gauge length of the plate sample with a thickness of not less than 0.5mm is L4=5.65. After. For the plate with a thickness of less than 0.5mm, the gauge length of the strip sample is Lg=50mm, and the sample width b. -12.5mm, 2.3 Surface quality 2.3,1 The surface of the product should be bright. No defects such as cracks, peeling, folding, obvious oxidation, metal and non-metallic indentation are allowed. 2.3.2 The surface of the product is allowed to have slight scratches and roller marks, and there are no traces of grinding after rolling. 2.3.3 For plates with a thickness greater than 40mm, the manufacturer is allowed to remove small surface defects, and the thickness after removal shall not be less than the minimum allowable size. 2.3. For square products, a small amount of missing corners that does not affect the rounding is allowed in the four right angles. 2.4 The product should not have stratification and inclusions. 3 Test methods 3.1 Chemical composition arbitration analysis method The chemical composition arbitration analysis method of pure saws shall be carried out in accordance with YB942 (1~15)-78 "Button saw analysis method". 3.2 Room temperature mechanical properties test method The room temperature mechanical properties test method of large materials, materials with a thickness of not less than 0.5mm shall be carried out in accordance with GB228~76 "Metal Tensile Test Method". For materials with a thickness of less than 0.5 mm, the test shall be conducted in accordance with GB3076-82 "Metallic Sheet (Strip) Tensile Test Method". 3.3 Dimension Measurement Method Measure the thickness of plates and strips with a first-class micrometer at a distance of not less than 10 mm from the edge. The thickness of foils shall be measured with a lever dry micrometer or an electronic micrometer. Measure the width and length with a steel ruler or a tape measure. Inspection Rules 4.1 Inspection and Acceptance 4.1.1 Sawn timber shall be inspected by the supplier's technical supervision department and the product quality shall be guaranteed to meet the requirements of this standard. 4.1.2 The purchaser may inspect the received products. If the inspection results do not conform to the provisions of this standard, the purchaser shall submit the matter to the supplier within three months from the date of receipt of the product and the two parties shall resolve the issue through negotiation. 4.2 Batches Sawn timber shall be submitted for acceptance in batches. Each batch consists of sawn timber of the same grade, melting furnace number or sintering furnace number, manufacturing method, specification and state. 4.3 Inspection items Each batch of steel shall be inspected for size and surface quality. 4.4 Sampling location and number of samples 4.4.1 Chemical composition shall be reported as the chemical composition of the original ingot or sintered steel. 4.4.2 Sampling of mechanical properties at room temperature, two longitudinal specimens shall be randomly selected from each batch of products for room temperature tensile test. 4.5 Repeated test If one specimen fails the room temperature tensile test, double the specimens shall be taken for re-test. If one specimen still fails the re-test, the whole batch shall be scrapped or two specimens shall be taken one by one for the test of the unqualified items. The qualified ones shall be accepted as a separate batch. 5 Marking, packaging, transportation, storage GB3630-88 5.1 In addition to the inspection mark, each package box should be labeled or marked with: supplier name, product brand, specification and status, product batch number and furnace number. 5.2 Packaging, transportation and storage 5.2.1 Each sheet should be separated by soft paper and then packed in boxes. 5.2.2 The strip should be wrapped with moisture-proof paper and placed in a dry box. The rolls should be tightly packed with filling materials to prevent movement. 5.2.3 The foil should be wound on a hard plastic cylinder and firmly wrapped with plastic cloth and plastic bags, and then packed in boxes. 4 The box should be lined with moisture-proof paper, and the words or signs such as "moisture-proof" and "handle with care" should be marked on the outside of the box. 5.2.4 5.2.5 During transportation and storage, the products must be protected from damage, moisture, and corrosion by active chemical agents. 5.3 Quality Certificate Each batch of sawn timber shall be accompanied by a quality certificate, which shall indicate: supplier name + product name, product brand, specification and status; product batch number, batch weight, furnace number and number of pieces; various analysis and test results and inspection department stamp: this standard number; packaging date. Additional Notes: This standard was proposed by the Ministry of Metallurgical Industry of the People's Republic of China. This standard was drafted by Baoji Nonferrous Metal Processing Plant. The main drafters of this standard were Ling Songwei and Cao Qidong. National Standard of the People's Republic of China Sawn plates, strips and foils GB 3630—R3 Published by China Standards Press (Erlihe, Fuwai, Beijing) Printed by the printing workshop of China Standards Press Distributed by Beijing Distribution Office of Xinhua Bookstore Sold by Xinhua Bookstores in various places Format 880×1230 1/16 Printing sheet 1/2 Number of words 7,000 First edition in March 1984: First printing in March 1984 Number of copies 1-4,000 [No. 5: 15169-1-1971 1 Price D.16 Yuan Standard 4-12 E80898 Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.