CB/T 3606-1993 Quality requirements for installation of electromechanical equipment CB/T3606-1993 standard download decompression password: www.bzxz.net

Ship Industry Standard of the People's Republic of China
CB/T3606-93
Quality requirements for installation of electromechanical equipment
Published on November 8, 1993
China State Shipbuilding Corporation
Implementation on May 1, 1994
Ship Industry Standard of the People's Republic of China
Quality requirements for installation of electromechanical equipment
Subject content and scope of application
This standard specifies the installation quality requirements for ship electromechanical equipment. This standard applies to the installation of mechanical and electrical equipment in the ship's cabin except the main engine and main generator set. 2 Alignment of the assembly of prime movers and auxiliary machines
2.1 The alignment requirements of the assembly of prime movers and auxiliary machines shall be in accordance with Table 1Table 1
Connection type
Rigid connection
Elastic connection
3 Quality requirements for the installation of mechanical and electrical equipment
3.1 The positioning of mechanical and electrical equipment shall meet the requirements of the design drawings, and the axis offset
≤ 0. 05
3.2 The spacers, pads and bolts used for installation shall comply with the requirements of the design drawings. 3.3
General installation requirements are as shown in Table 2.
China State Shipbuilding Corporation approved CB/T3606-93 on November 8, 1993
Classification number: U42
Axis bend
Implementation on May 1, 1994
Installation example
CB/T3606-93
Installation requirements
2. Double nuts are used for the bottom bolts;
b. The upper plane of the welding gasket should be Tilt, the slope is about 1:100;
C. Before tightening the machine base and the foundation with bolts, check the live gasket and the machine base surface with a 0.05mm feeler gauge
, and the insertion depth shall not exceed 10mm,
a. The thickness of the welding pad should be greater than 1.25 times the bolt diameter:
b. After the bolts are tightened, check with a 0.05mm feeler gauge, and the insertion depth shall not exceed 10mm
a. The thickness of the welding pad should be greater than 1.25 times the bolt diameter;
b. After the bolts are tightened, use a test hammer to check the tightening condition:
c. The contact between the mounting surfaces should be good.
After the bolts are tightened, check with a 0.05mm feeler gauge. The insertion depth should not exceed 10mm.
After the machine base is in place, no more than three steel sheets or pot skins are allowed to be used as gaskets between each support, but half a gasket is not allowed.
Note: 1) Generally refers to the machine with a motor power not exceeding 10kW and a machine base fixing bolt not exceeding M27. 3.4 Live gaskets may also be epoxy injection gaskets approved by the ship inspection department. Scope of application: a. Machinery with two or more cylinders and reciprocating motion: b. Emergency generator sets; c. Center bearings; a. Machinery driven by electric motors; b. Pumps with a common base; a. Shell expansion heat exchangers; b. Pressure vessels (height not more than 1m); c. Large filters; d. Evaporators: e. Machinery and equipment installed on the bulkhead. a. Single cylinder diesel engine;
b. Reciprocating cylinder:
c. Heat exchanger with non-expanding shell:
d. Machinery driven by electric motor: (machine base fixing bolt is larger than M27);
e. Pressure vessel (height is larger than 1m),
8. Machinery driven by electric motor with power less than 2.2kW;b. Small filter:www.bzxz.net
c. Machinery with rubber dew avoider;
d. Unprocessed base, machine base and cabinet bottom feet
3.5 When using tight-fitting bolts and locating pins for positioning, the clearance or interference of the matching should not be greater than 0.005mm. 3.6 When using thrust block for lateral positioning, the thrust surface should be close to each other, and the insertion depth should not exceed 10mm when checked with a 0.05mm feeler gauge. 3.7 After installation, the protruding length of the bolt (column) head is 1~2 pitches. 2
Additional Notes:
This standard is proposed by China State Shipbuilding Corporation. CB/T3606-93
This standard is under the jurisdiction of the 603rd Institute of China State Shipbuilding Corporation. This standard was drafted by China Shipbuilding Corporation. The main drafters of this standard are: Yu Weihai,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.