This standard specifies the technical requirements, test methods, inspection rules and marking, packaging, transportation and storage requirements for industrial linear alkylbenzene. This standard applies to industrial linear alkylbenzene produced by dehydrogenation and cracking methods. This product is mainly used in the production of synthetic detergents. The molecular formula of industrial linear alkylbenzene is: R—C6H5 (R is an average dodecyl group). GB/T 5177.5-2002 Industrial linear alkylbenzene GB/T5177.5-2002 Standard download decompression password: www.bzxz.net

1cs 71. 080- 15
National Standard of the People's Republic of China
GB/T 5177. 5—2002
Induslrial linear alkylbenzene2002-07-22 Issued
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China
2003-02-01Implementation
GB/T5177.5—2002
This standard is in accordance with GB/T5177.5—2002. This standard mainly stipulates the following contents: 1. Standard naming;
2. Standard application;
3. Inspection cycle of biodegradability;
Determination method of density;
, water content determination method!
6. 3. Detailed location This standard is from the implementation, and replaces GR/T5-77.5-1993 proposed by China Light Industry Federation. This standard is also under the jurisdiction of the National Surfactant Detergent Standardization Center. The main issuing units of this standard are PetroChina Petrochemical Corporation, China National Institute of Chemical Industry, and the following are the main testers. 1 Scope National Standard of the People's Republic of China Industrial linear alkylbenzene GB/T 5177.5-2002 Replaced by CB/I E111.51993 This standard specifies the technical requirements, test methods, inspection specifications, packaging, transportation and storage requirements of industrial straight-chain alkylbenzene. This standard applies to the production of T-type straight-chain alkyl ethers by hydrogenation and decomposition, and the products are mainly used for the production of synthetic dyes. The molecular formula of T-type straight-chain alkyl ethers is R-HR, which is an average of 12 mass %: 2 Reference standards || tt || The following standards contain provisions that constitute the provisions of this standard through reference in the standard band. When this standard is published, the version shown is effective. All standards are subject to revision. The most accurate technical standards should be checked for the latest editions of the following standards: GE/6:1-13 General method for refractometry of chemical reagents (IS063531:1U82GM27GB1E84--1992 Density determination of crude oil and liquid petroleum products (densitometer method) (r.cg15) 3875:1!7) 5177.-19 Determination of color of burning oil () 11:1SS7) 577.2133 Determination of sulfonate content in dialkylbenzene GE/T 5177.3-1985
! Industrial alkylbenzene index determination of gas-liquid and Nova 5 industrial alkylbenzene index determination of potentiometric drip CB/T51774—1985
G1/T G536—137
GB/T66521992
GH/[ 733-1'93
Shizhou product evaporation method ASM56: 1995
Determination of water content and test method c15) 5.187 Surfactants and detergents containing water - determination of the corrected value of the following calorimetric method [e1S031711CB/T811987
Adjusted value of the thermal measurement
113-1995 Decomposition and ionization of surfactants - test method e1S5363: 990) 3 Technical requirements
Requires clear white, no floating liquid. bZxz.net
3.2 Numerical degradation
Industrial sodium alkyl sulfonate prepared by membrane and precipitation of alkyl benzene, the biodegradability of the components is not dependent on treatment. 3.3 Treatment of the following standards 1 The physical and chemical indicators of the industrial chain system shall conform to the standards in Table 1. The industrial test system indexes shall not be lower than those of first-class products. Approved by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China on 200-7-22, 2003-02-01 Implementation date: Color/n Refractive index Density (°C <20°C)/tg/ml: Mixture value (g/100g) Magnetizable head Average relative molecular weight Content/% Body weight 5 Yuan Content 95 4 Test method GR/T5177.5—2002 Fast-moving products 1. 482 0~1. 48.
First-class
1. 4RZ (~1. 4RT I
h x55, R70)
258~-253
Compound drug
1. 483 0~-1. 43 m
235--250
Analysis Unless otherwise specified, use analytical reagents and distilled water (in accordance with the one-sensitive water in GB/6682). 4.1 Appearance determination
Put the sample in a stable cup or a flask and inspect visually at 25°C. 4.2 Determination of moisture content
Determine in accordance with GB5177.4.
4.3 Determination of refractive index
Determine in accordance with GB/T614.
4.4 Determination of temperature
Determine in accordance with GB/T1884.
4.5 Determination of molten salt
Determine in accordance with GB/T5177.4.
4.6 Determination of sulfonate content
Determine in accordance with GB/T5177.2.
4.7 Determination of average relative molecular mass
Determine in accordance with GB/T6177.3.
4.B Determination of moisture content
Determine in accordance with GB/T 7380.
4. 9 Determination of degradation rate
Determine according to G14/6536.
4.10 Determination of biodegradability
Determine according to K15318
5 Inspection rules
5.1 Inspection classification
5.1.1 Type inspection
GB/T 5177.5—2002
All technical requirements and indicators specified in this standard shall be inspected in the following circumstances: 1) When there are changes in production, raw materials and processes that may affect product quality; 2) When resuming production after a long period of suspension,
3) When there is a large difference between the factory inspection result and the last type inspection result; 4) During normal production, a type inspection shall be carried out every two years; 5.12 Factory acceptance
Except for the group analysis, all items are subject to factory inspection. 5.2 Batching and sampling rules
5.2.1 Industrial products shall be delivered and sampled in batches, and products of the same specification, grade and batch delivered at the same time shall constitute a batch.
Products leaving the factory shall be inspected and certified by the quality inspection department of the production unit according to this standard. The product quality inspection certificate shall be issued at the receiving point for acceptance. If necessary, it can be inspected and accepted in detail according to the following provisions within one year. 5.2.2 Sampling
5.2.2.1 When the batch is reduced to 1, take the piece from the batch at random according to the batch size. 5.2.2.2 For the oil end with uniform horizontal surface, take samples by combining the test rods from the top of the tank to the bottom of the tank at one-third, one-half and five-sixths of the liquid level. 5.2.2.3 For the oil end of the train oil car and the automobile oil end, take samples at the rolling surface of the fuel tank at the depth of two-thirds. 5.2.2.4 Take a total of 3k samples from each sample unit and pack them into the next sample bag, add a seal, and note the sample name, grade, batch size, production unit, sampling date and person who took it. Both parties shall hold a copy of the inspection form and the lender shall keep a copy for inspection. The samples shall be stored in a dark place for a storage period of 10 days. If the consignee finds that the container and seal are not intact or damaged, he shall immediately report to the transportation department together with the manufacturer. 5.3 Determination of the quality of the product shall be determined by comparing the physical and chemical indexes with the (B/817C) monthly revised value. If the test index does not meet the requirements of this standard, the product can be re-sampled twice from the delivered batch. If the re-test result is still unsatisfactory, the batch is judged to be unqualified. 5.4. If the two parties still have disputes over the inspection results, they can conduct arbitration and the arbitration result shall be the most comprehensive. 6. Labeling, packaging, transportation and storage G/T 5177.5-2002 6-1 The packaging containers should be marked with: a) product name, product number and packaging batch number; b) net content and weight; d) producer name, place of origin and postal code. 6.2 The packaging of industrial straight chain alkyl should be made of special oil (the car will not be corroded or sprayed, and the packaging can ensure the resistance to mechanical contamination). The product should be packed with air according to the temperature and leave space for passengers. The packaging container should be clean and contain reasonable weight. The industrial straight chain should be kept in a safe place during transportation. Avoid direct sunlight and moisture during loading and unloading. 6.3 The industrial straight chain should be stored in a covered place! It should be placed outdoors to prevent rain. 6.4
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.