This standard specifies the technical requirements, test methods, inspection rules, packaging and marking requirements for the emblem of the Hong Kong Special Administrative Region of the People's Republic of China. This standard applies to regional emblems made of aluminum alloy or glass fiber reinforced plastic. Regional emblems made of other materials must also refer to this standard. GB 16690-1996 Regional Emblem of the Hong Kong Special Administrative Region GB16690-1996 Standard download and decompression password: www.bzxz.net

GB16690—1996
Previous
Preface
1. This standard is based on Article 10 of the Basic Law of the Hong Kong Special Administrative Region of the People's Republic of China and the "Basic Law of the Hong Kong Special Administrative Region of the People's Republic of China (Draft)" )\Description of Related Documents" has compiled the standard Appendix A "Description of the Regional Emblem of the Hong Kong Special Administrative Region of the People's Republic of China"
2. This standard is based on the National People's Representative of the People's Republic of China on August 10, 1996. Annex 2 "Instructions for the Production of the Regional Emblem of the Hong Kong Special Administrative Region of the People's Republic of China" of the "Interim Measures for the Use of the Regional Flag and Regional Emblem of the Hong Kong Special Administrative Region of the People's Republic of China" adopted by the fourth plenary session of the Hong Kong Special Administrative Region Preparatory Committee of the General Assembly formulated the Hong Kong Special Administrative Region of the People's Republic of China Technical requirements for the shape, pattern, standard size, plate making and positioning of the emblem of the Special Administrative Region, and this document is included in Appendix B of the standard. 3. The red color value and color difference of the Hong Kong Special Administrative Region emblem and the emblem topcoat in this standard. Important technical parameters such as film performance requirements, material strength, emblem evaluation, test methods, inspection rules, marking, and packaging refer to the corresponding indicators in GB15093-1994 "National Micro".
In addition, this document. The standard also confirms the Y value of the redbud petals based on the characteristics of the regional emblem pattern, and adds the regional emblem profile. Appendix A, Appendix B and Appendix C of this standard are appendices to the standard. This standard is proposed by the Hong Kong and Macao Affairs Office of the State Council. . This standard is under the jurisdiction of the Standardization Department of the State Administration of Technology. The unit responsible for drafting this standard: National Color Standardization Technical Committee. The main drafters of this standard: Sun Xiuru, Wang Yunqiang, Han Yue, Guo Chunpeng, Yu Shengli, Zhang Jiaying. tt||National Standard of the People's Republic of China
Regional emblem of Hong Kong Special Administrative Region
Regional emblem of HongKong special administrative regionGB16690-1996
This standard specifies the emblem of Hong Kong special administrative region of the People's Republic of China (hereinafter referred to as the regional emblem) technical requirements, test methods, inspection rules and packaging, marking requirements
This standard applies to regional emblems made of aluminum alloy or glass fiber reinforced plastics, and regional emblems made of other materials. Reference shall also be made to this standard. 2 Referenced standards
The following standards contain provisions that constitute provisions of this standard at the time of publication of this standard. been revised, parties using this standard should explore the possibility of using the latest version of the following standards. GB/T1449-1983 Test methods for bending properties of glass fiber reinforced plastics GB/T1720-1979
GB/T1729-1979|| tt||GB/T1733—1979
Determination of paint film adhesion
Determination of paint film color and appearance
Determination of paint film water resistance
GB1740—1979 (88)
Determination method of paint film resistance to moisture and heat
GB1766—1995
Rating method for aging of paint and varnish coatings GB1771—1991
GB 3854—1983| |tt||GB4380—1984
GB 6739—1986
GB 7234-1987
GB9274—1988
GB 9754—1988
Color paint and Determination of the neutral salt spray resistance of varnishes. Barcol (Baccol) hardness test method for fiber-reinforced plastics. Method for determining roundness error. Two-point and three-point method. Pencil determination method for coating film hardness
terminology of roundness measurement, Definition and Parameters
Determination of the resistance of paints and varnishes to liquid media
Determination of 20°, 60° and 85° specular gloss of paint films of paints and varnishes that do not contain metallic colors GB11186. 2—1989
GB 11186. 31989
Measurement method of coating film color Part 2 Color measurement Method of measurement of coating film color
Part 3
Flatness error Testing
GB/T11337-1989
GB15093-1994 National Emblem
3 Definitions
This standard adopts the following definitions.
Color Difference Calculation
3.1 The emblem of the Hong Kong Special Administrative Region
refers to the emblem of the Hong Kong Special Administrative Region established by the People's Republic of China. In the center is a five-star steamed bauhinia flower, with the words "People's Republic of China" written around it. The emblem of the Hong Kong Special Administrative Region of the Republic of China and the English "HONGKONG" (Hong Kong). 3.2 Bauhinia petal white refers to the specific reflectance white of the bauhinia petals on the regional emblem. Approved by the State Technical Supervision Bureau on 1996-12-25 and implemented on 1997-02-01. |tt||4 requirements
4.1 The shape and pattern of the regional emblem
GB166901996
The shape and pattern of the regional emblem shall be in accordance with the Basic Law of the Hong Kong Special Administrative Region of the People's Republic of China and the The relevant provisions in "Administrative District Emblem Pattern Description" are implemented. See Appendix A (Standard Appendix) and Figure 1. tt | .1 The standard size and plate-making positioning of the regional emblem shall be in accordance with the relevant provisions of the "Instructions for the Production of the Regional Emblem of the Hong Kong Special Administrative Region of the People's Republic of China". See Appendix B (Standard Appendix), Table 1, Figure 2, Figure 3 and Appendix C (Standard Appendix). 4.2.2 When making non-standard size regional emblems due to special needs, they will be enlarged or reduced in proportion to the standard size and allowable error. Table 1 Standard dimensions and allowable errors of regional emblem
Gage
Item
Emblem surface diameter, mm
Red overall thickness, mm
Red ring narrow edge Width, mm
Red Bauhinia stamen width, mm
Red inner circle diameter, mm
Mesh
White Bauhinia circumscribed circle diameter, mm
Red Diameter of the circumcircle of the five-pointed star, mm
Chinese character area angle
Code number in Figure 2
No. 1
1000±6
T|| tt||B
B
α
46±3
10±0.5
2.5±1
780±3|| tt||600+3
50±2
220°±1°
No. 2
800±5
36±2||tt ||8±0.5
2±1
624±2
480±2
40±1.5
220°±1°||tt ||Grid
No. 3
600±4
28±1
6±0.5
1.5±1
468±1.5
360±1.5
30±1
220°±1°
English word area angle
Pentagram positioning angle
Item
Bauhinia petal positioning angle
External bevel angle
Object
Chinese, English. Five-pointed star positioning radius, mm Chinese character height, mm||tt| |Height of English letters mm
Pentagram depth, mm
Thickness of red inner circle, mm
Thickness of Chinese and English characters +mm
Thickness of purple petals, mm| | tt | |tt||Micro back mounting screw hole
4.3 zone emblem surface color and allowable error
GB16690—1996
Table 1 (End)
In Figure 2 Code
No. 1
80°±1°
a
as
a
R
H|| tt||H
T.
T.
T.
Ts
T.
Et
S
E
M
110°±1°
14°±2°
5°～8°
440±2
70±2.5
60±2.5
10±1
10±1
10±1
10±1
3.5+0.5| |tt||15±1
2
3
5
M12X1.75
Regulations
No. 2||tt| |80°±1°
110°±1°
14°±2°
5°~8°
352±1.5
56 ±2
48+2
8±1
8±1
8±1
8±1
2.5+0.5
12±1
1.5
2
4
M10×1.5
grid
No. 3||tt ||80\+1°
110°±1°
14°±2°
5°~8°bZxz.net
264±1
42±1.5
36±1.5
5±1
5±1
5±1
5+1
1.5+ 0.5
8±1
1
2
3
M8X1.25
4.3.1 emblem red: aluminum alloy, The red color and allowable error of the regional emblem made of glass fiber reinforced plastic are the same as the red color and allowable error of the national emblem made of aluminum alloy and glass fiber reinforced plastic in GB15093 respectively. 4.3.2 Bauhinia petals white: The stimulation value of the white bauhinia petals of the regional emblem made of aluminum alloy and glass fiber reinforced plastic shall not be less than 80.
4.3.3 The red color and allowable error of the regional emblem surface made of other materials shall be subject to the national emblem red color and allowable error of aluminum alloy in GB15093. The stimulation value Y of the white petals of Bauhinia is consistent with the provisions of 4.3.2 of this standard. T2
T.
T+
Ts
武
人
Specialized
GB16690-1996||tt| |and
G
Picture 2 standard size of regional emblem
Hong Kong
Hong Kong
B
☆
中| |tt||O
B
Park
GB16690—1996
5-M
140°
90||tt| |Figure 3 Schematic diagram of the mounting holes on the back of the regional emblem
4.4 Chromaticity data calculation
GB16690-1996
The chromaticity data in 4.3 supplements the standard chromaticity with CIE standard illuminant D65 and CIE1964 System calculations. 4.5 Zone micro topcoat film performance requirements
zone micro topcoat film performance requirements are shown in Table 2.
Table 2
Microtopcoat film properties
Item
Paint film color and appearance
Weather resistance, grade
Gloss (60 °), %
adhesion, grade
hardness
water resistance (24h)
humidity and heat resistance (7d), grade
salt spray resistance Property (7 d), grade
4.6 material strength
mesh
not greater than
not less than
not less than
not less than| |tt||4.6.1 The bending strength of glass fiber reinforced plastics shall not be less than 140MPa. 4.6.2 The surface hardness of glass fiber reinforced plastic shall not be less than 30. 4.6.3 Falling ball impact strength: No cracks or damage to the body of the logo. 4.6.4 Free fall strength: No cracks or damage to the body of the logo. 4.7 Emblem surface evaluation
finger
mark
color meets the requirements of 4.3, smooth and bright
1
90
2B||tt| |No bubbling and no peeling
1
1
The regional emblem is evaluated based on the degree of impact on the appearance quality of the regional emblem. The inspection is carried out on a unit basis for each emblem. See the specific requirements. table 3. Table 3 Emblem surface evaluation
item
item
emblem surface appearance
micro surface color
requirement
request
The surface pattern is clear, and there must be no shrinkage holes, hot cracks, cold cracks, deformations, chipped edges, or broken edges. There must be no sand, impurities, or pores that obviously affect the appearance
No obvious stains, color matching, Color 4.8 The red fonts in Chinese and English on the regional emblem
4.8.1 The red fonts on the emblem "*Hong Kong Special Administrative Region of the People's Republic of China" should conform to the standard words on the regional emblem as shown in Figure 4. 4.8.2 On the emblem The red fonts in English\HONGKONG" (Hong Kong) should conform to the standard fonts of the regional emblem as shown in Figure 4. 5 Test methods
GB16690-1996
Figure 4 Chinese and English standard words on the regional emblem
5.1 The measurement of the micro-standard size and allowable error of the area should be measured using qualified and accurate Measuring tools with a temperature of not less than 0.5%. 5.2 Colorimetry measurement shall be carried out in accordance with the provisions of GB/T11186.2 and GB/T11186.3. 5.3 The performance of the emblem surface paint film shall be measured according to the regulations in GB/T1720, GB/T1729, GB/T1733, GB/T1766, GB/T9754, GB/T6739, GB/T9274, GB/T1740 and GB/T1771. 5.4 Strength test:
5.4.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely on the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a substandard product, and the unqualified product shall not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer's name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the package surface.5
Grid
No. 3
80\+1°
110°±1°
14°±2°
5 °~8°
264±1
42±1.5
36±1.5
5±1
5±1
5 ±1
5+1
1.5+0.5
8±1
1
2
3
M8X1 .25 | Be a hero. 4.3.2 Bauhinia petals white: The stimulation value of the white bauhinia petals of the regional emblem made of aluminum alloy and glass fiber reinforced plastic shall not be less than 80.
4.3.3 The red color and allowable error of the regional emblem surface made of other materials shall be subject to the national emblem red color and allowable error of aluminum alloy in GB15093. The stimulation value Y of the white petals of Bauhinia is consistent with the provisions of 4.3.2 of this standard. T2
T.
T+
Ts
武
人
Specialized
GB16690-1996||tt| |and
G
Picture 2 standard size of regional emblem
Hong Kong
Hong Kong
B
☆
中| |tt||O
B
Park
GB16690—1996
5-M
140°
90||tt| |Figure 3 Schematic diagram of the mounting holes on the back of the regional emblem
4.4 Chromaticity data calculation
GB16690-1996
The chromaticity data in 4.3 supplements the standard chromaticity with CIE standard illuminant D65 and CIE1964 System calculations. 4.5 Zone micro topcoat film performance requirements
zone micro topcoat film performance requirements are shown in Table 2.
Table 2
Microtopcoat film properties
Item
Paint film color and appearance
Weather resistance, grade
Gloss (60 °), %
adhesion, grade
hardness
water resistance (24h)
humidity and heat resistance (7d), grade
salt spray resistance Property (7 d), grade
4.6 material strength
mesh
not greater than
not less than
not less than
not less than| |tt||4.6.1 The bending strength of glass fiber reinforced plastics shall not be less than 140MPa. 4.6.2 The surface hardness of glass fiber reinforced plastic shall not be less than 30. 4.6.3 Falling ball impact strength: No cracks or damage to the emblem body. 4.6.4 Free fall strength: No cracks or damage to the emblem body. 4.7 Area Emblem surface evaluation
finger
mark
color meets the requirements of 4.3, smooth and bright
1
90
2B||tt| |No blistering and no peeling
1
1
The evaluation of the regional emblem is based on the degree of impact on the appearance quality of the regional emblem. The inspection is carried out on a unit basis for each emblem. See the specific requirements. table 3. Table 3 Emblem surface evaluation
item
item
emblem surface appearance
micro surface color
requirement
request
The surface pattern is clear, and there must be no shrinkage holes, hot cracks, cold cracks, deformations, chipped edges, or broken edges. There must be no sand, impurities, or pores that obviously affect the appearance
No obvious stains, color matching, Color 4.8 The red fonts in Chinese and English on the regional emblem
4.8.1 The red fonts on the emblem "*Hong Kong Special Administrative Region of the People's Republic of China" should conform to the standard words on the regional emblem as shown in Figure 4. 4.8.2 On the emblem The red fonts in English\HONGKONG" (Hong Kong) should conform to the standard fonts of the regional emblem as shown in Figure 4. 5 Test methods
GB16690-1996
Figure 4 Chinese and English standard words on the regional emblem
5.1 The measurement of the micro-standard size and allowable error of the area should be measured using qualified and accurate Measuring tools with a temperature of not less than 0.5%. 5.2 Colorimetry measurement shall be carried out in accordance with the provisions of GB/T11186.2 and GB/T11186.3. 5.3 The performance of the emblem surface paint film shall be measured according to the regulations in GB/T1720, GB/T1729, GB/T1733, GB/T1766, GB/T9754, GB/T6739, GB/T9274, GB/T1740 and GB/T1771. 5.4 Strength test:
5.4.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely to the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a substandard product, and the unqualified product shall not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer’s name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the package surface.5
Grid
No. 3
80\+1°
110°±1°
14°±2°
5 °~8°
264±1
42±1.5
36±1.5
5±1
5±1
5 ±1
5+1
1.5+0.5
8±1
1
2
3
M8X1 .25 | Be a hero. 4.3.2 Bauhinia petals white: The stimulation value of the white bauhinia petals of the regional emblem made of aluminum alloy and glass fiber reinforced plastic shall not be less than 80.
4.3.3 The red color and allowable error of the regional emblem surface made of other materials shall be subject to the national emblem red color and allowable error of aluminum alloy in GB15093. The stimulation value Y of the white petals of Bauhinia is consistent with the provisions of 4.3.2 of this standard. T2
T.
T+
Ts
武
人
Specialized
GB16690-1996||tt| |and
G
Picture 2 standard size of regional emblem
Hong Kong
Hong Kong
B
☆
中| |tt||O
B
Park
GB16690—1996
5-M
140°
90||tt| |Figure 3 Schematic diagram of the mounting holes on the back of the regional emblem
4.4 Chromaticity data calculation
GB16690-1996
The chromaticity data in 4.3 supplements the standard chromaticity with CIE standard illuminant D65 and CIE1964 System calculations. 4.5 Performance requirements of micro topcoat film in zone
The performance requirements of micro topcoat film in zone are shown in Table 2.
Table 2
Microtopcoat film properties
Item
Paint film color and appearance
Weather resistance, grade
Gloss (60 °), %
adhesion, grade
hardness
water resistance (24h)
humidity and heat resistance (7d), grade
salt spray resistance Property (7 d), grade
4.6 material strength
mesh
not greater than
not less than
not less than
not less than| |tt||4.6.1 The bending strength of glass fiber reinforced plastics shall not be less than 140MPa. 4.6.2 The surface hardness of glass fiber reinforced plastic shall not be less than 30. 4.6.3 Falling ball impact strength: No cracks or damage to the emblem body. 4.6.4 Free fall strength: No cracks or damage to the emblem body. 4.7 Area Emblem surface evaluation
finger
mark
color meets the requirements of 4.3, smooth and bright
1
90
2B||tt| |No blistering and no peeling
1
1
The evaluation of the regional emblem is based on the degree of impact on the appearance quality of the regional emblem. The inspection is carried out on a unit basis for each emblem. See the specific requirements. table 3. Table 3 Emblem surface evaluation
item
item
emblem surface appearance
micro surface color
requirement
request
The surface pattern is clear, and there must be no shrinkage holes, hot cracks, cold cracks, deformations, chipped edges, or broken edges. There must be no sand, impurities, or pores that obviously affect the appearance
No obvious stains, color matching, Color 4.8 The red fonts in Chinese and English on the regional emblem
4.8.1 The red fonts on the emblem "*Hong Kong Special Administrative Region of the People's Republic of China" should conform to the standard words on the regional emblem as shown in Figure 4. 4.8.2 On the emblem The red fonts in English\HONGKONG" (Hong Kong) should conform to the standard fonts of the regional emblem as shown in Figure 4. 5 Test methods
GB16690-1996
Figure 4 Chinese and English standard words on the regional emblem
5.1 The measurement of the micro-standard size and allowable error of the area should be measured using qualified and accurate Measuring tools with a temperature of not less than 0.5%. 5.2 Colorimetry measurement shall be carried out in accordance with the provisions of GB/T11186.2 and GB/T11186.3. 5.3 The performance of the emblem surface paint film shall be measured according to the regulations in GB/T1720, GB/T1729, GB/T1733, GB/T1766, GB/T9754, GB/T6739, GB/T9274, GB/T1740, and GB/T1771. 5.4 Strength test:
5.4.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely to the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a substandard product, and the unqualified product will not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer's name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the package surface.
T+
Ts
武
人
特
GB16690-1996
和
G
Picture 2 standard size of regional emblem
Hong Kong
Hong Kong
B
☆
中
O||tt ||B
Park
GB16690—1996
5-M
140°
90
Figure 3 Mounting holes on the back of the regional emblem Schematic
4.4 Colorimetric data calculation
GB16690-1996
The colorimetric data in 4.3 is calculated using CIE standard illuminant D65 and CIE1964 to supplement the standard colorimetric system. 4.5 Zone micro topcoat film performance requirements
zone micro topcoat film performance requirements are shown in Table 2.
Table 2
Microtopcoat film properties
Item
Paint film color and appearance
Weather resistance, grade
Gloss (60 °), %
adhesion, grade
hardness
water resistance (24h)
humidity and heat resistance (7d), grade
salt spray resistance Property (7 d), grade
4.6 material strength
mesh
not greater than
not less than
not less than
not less than| |tt||4.6.1 The bending strength of glass fiber reinforced plastics shall not be less than 140MPa. 4.6.2 The surface hardness of glass fiber reinforced plastic shall not be less than 30. 4.6.3 Falling ball impact strength: No cracks or damage to the emblem body. 4.6.4 Free fall strength: No cracks or damage to the emblem body. 4.7 Area Emblem surface evaluation
finger
mark
color meets the requirements of 4.3, smooth and bright
1
90
2B||tt| |No bubbling and no peeling
1
1
The regional emblem is evaluated based on the degree of impact on the appearance quality of the regional emblem. The inspection is carried out on a unit basis for each emblem. See the specific requirements. table 3. Table 3 Emblem surface evaluation
item
item
emblem surface appearance
micro surface color
requirement
request
The surface pattern is clear, and there must be no shrinkage holes, hot cracks, cold cracks, deformations, chipped edges, or broken edges. There must be no sand, impurities, or pores that obviously affect the appearance
No obvious stains, color matching, Color 4.8 The red fonts in Chinese and English on the regional emblem
4.8.1 The red fonts on the emblem "*Hong Kong Special Administrative Region of the People's Republic of China" should conform to the standard words on the regional emblem as shown in Figure 4. 4.8.2 On the emblem The red fonts in English\HONGKONG" (Hong Kong) should conform to the standard fonts of the regional emblem as shown in Figure 4. 5 Test methods
GB16690-1996
Figure 4 Chinese and English standard words on the regional emblem
5.1 The measurement of the micro-standard size and allowable error of the area should be measured using qualified and accurate Measuring tools with a temperature of not less than 0.5%. 5.2 Colorimetry measurement shall be carried out in accordance with the provisions of GB/T11186.2 and GB/T11186.3. 5.3 The performance of the emblem surface paint film shall be measured according to the regulations in GB/T1720, GB/T1729, GB/T1733, GB/T1766, GB/T9754, GB/T6739, GB/T9274, GB/T1740 and GB/T1771. 5.4 Strength test:
5.4.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely on the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a unqualified product, and the unqualified product shall not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer’s name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the package surface.
T+
Ts
武
人
特
GB16690-1996
和
G
Picture 2 standard size of regional emblem
Hong Kong
Hong Kong
B
☆
中
O||tt ||B
Park
GB16690—1996
5-M
140°
90
Figure 3 Mounting holes on the back of the regional emblem Schematic
4.4 Chromaticity data calculation
GB16690-1996
The chromaticity data in 4.3 is calculated using the CIE standard illuminant D65 and CIE1964 supplementary standard chromaticity system. 4.5 Performance requirements of micro topcoat film in zone
The performance requirements of micro topcoat film in zone are shown in Table 2.
Table 2
Microtopcoat film properties
Item
Paint film color and appearance
Weather resistance, grade
Gloss (60 °), %
adhesion, grade
hardness
water resistance (24h)
humidity and heat resistance (7d), grade
salt spray resistance Property (7 d), grade
4.6 material strength
mesh
not greater than
not less than
not less than
not less than| |tt||4.6.1 The bending strength of glass fiber reinforced plastics shall not be less than 140MPa. 4.6.2 The surface hardness of glass fiber reinforced plastic shall not be less than 30. 4.6.3 Falling ball impact strength: No cracks or damage to the emblem body. 4.6.4 Free fall strength: No cracks or damage to the emblem body. 4.7 Area Emblem surface evaluation
finger
mark
color meets the requirements of 4.3, smooth and bright
1
90
2B||tt| |No blistering and no peeling
1
1
The evaluation of the regional emblem is based on the degree of impact on the appearance quality of the regional emblem. The inspection is carried out on a unit basis for each emblem. See the specific requirements. table 3. Table 3 Emblem surface evaluation
item
item
emblem surface appearance
micro surface color
requirement
request
The surface pattern is clear, and there must be no shrinkage holes, hot cracks, cold cracks, deformations, chipped edges, or broken edges. There must be no sand, impurities, or pores that obviously affect the appearance
No obvious stains, color matching, Color 4.8 The red fonts in Chinese and English on the regional emblem
4.8.1 The red fonts on the emblem "*Hong Kong Special Administrative Region of the People's Republic of China" should conform to the standard words on the regional emblem as shown in Figure 4. 4.8.2 On the emblem The red fonts in English\HONGKONG" (Hong Kong) should conform to the standard fonts of the regional emblem as shown in Figure 4. 5 Test methods
GB16690-1996
Figure 4 Chinese and English standard words on the regional emblem
5.1 The measurement of the micro-standard size and allowable error of the area should be measured using qualified and accurate Measuring tools with a temperature of not less than 0.5%. 5.2 Colorimetry measurement shall be carried out in accordance with the provisions of GB/T11186.2 and GB/T11186.3. 5.3 The performance of the emblem surface paint film shall be measured according to the regulations in GB/T1720, GB/T1729, GB/T1733, GB/T1766, GB/T9754, GB/T6739, GB/T9274, GB/T1740 and GB/T1771. 5.4 Strength test:
5.4.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely on the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a unqualified product, and the unqualified product shall not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer's name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the package surface.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely to the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a substandard product, and the unqualified product will not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer’s name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the surface of the package.1 The bending strength test of glass fiber reinforced plastics shall be carried out in accordance with the provisions of GB/T1449. 5.4.2 Falling ball impact: Place the micro-sample face up, lay it horizontally on the cement floor, place a 112g steel ball 2m above the sample, and drop the steel ball freely to the same part of the logo surface, repeat Impact three times and observe whether there are cracks, deformation, delamination, etc. on the surface of the sample.
5.4.3 Drop test: Hang the regional emblem sample vertically at a height of 1m from the cement floor, and repeat the free fall twice to observe whether there are cracks, cracks and delamination on the surface.
5.4.4 Measure the microhardness of areas made of glass fiber reinforced plastics according to the regulations in GB3854. 5.5 The unevenness test shall be carried out according to method b of 4.4 in GB/T11337. 5.6 Roundness test is carried out according to the two-point measurement method of 2.3 in GB4380. 6 Inspection Rules
6.1 The shape, pattern and standard size of the regional emblem, emblem surface evaluation, and color quality inspection are factory inspections. When materials, formulas, and processes change, type inspection should be carried out.
6.2 During the factory inspection, if all inspection items of each product are qualified, it will be judged as a qualified product, otherwise it will be a substandard product, and the unqualified product will not leave the factory.
GB16690—1996
During type inspection, if all the quality requirements specified in Chapter 4 are qualified, it will be judged as qualified and formal production will be allowed. 7 Logo and packaging
7.1 Logo
The manufacturer's name and product number should be indicated on the back of each logo. 7.2 Packaging
7.2.1 Each product must be individually packaged. The packaging must ensure that the product quality is not damaged and facilitate transportation and storage. The product name, specification, material, packaging size, weight, manufacturer name, and transportation mark should be indicated on the outside of the package. The necessary accessories for installation, installation and storage instructions and inspection certificates should be included in the package. The certificate should indicate the product name, specifications, material, product number, date of manufacture, manufacturer's name and address, and inspector's name (code name).
7.2.2 The packaging of batch products should ensure that the product quality is not damaged and facilitate transportation. The product name, specifications, material, quantity, packaging size, weight, manufacturer name, and transportation mark should be marked on the surface of the package.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.