title>JB/T 9956-1999 Accuracy of crocodile shears - JB/T 9956-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 9956-1999 Accuracy of crocodile shears
JB/T 9956-1999 Accuracy of crocodile shears

Basic Information

Standard ID: JB/T 9956-1999

Standard Name: Accuracy of crocodile shears

Chinese Name: 鳄鱼式剪断机 精度

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-05-14

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:Machinery Manufacturing>>Chipless Processing Equipment>>25.120.10 Forging Equipment, Punching Machines, Shearing Machines

Standard Classification Number:Machinery>>General Processing Machinery and Equipment>>J62 Forging Machinery

associated standards

alternative situation:Original standard number ZB J62010-1987

Procurement status:GOCT 16125-81 MOD

Publication information

other information

Focal point unit:National Forging Machinery Standardization Technical Committee

Publishing department:National Forging Machinery Standardization Technical Committee

Introduction to standards:

JB/T 9956-1999 This standard is a revision of ZB J62 010-87 "Accuracy of Crocodile Shears". This standard specifies the accuracy and inspection method of crocodile shears. This standard applies to mechanical transmission crocodile shears for cold shearing of metal scrap (the tensile strength of the sheared material should not be greater than 500MPa). This standard was first issued in April 1987. JB/T 9956-1999 Accuracy of Crocodile Shears JB/T9956-1999 Standard download decompression password: www.bzxz.net

Some standard content:

[CS 25.120.10
Machinery Industry Standard of the People's Republic of China
JB/T9956-1999
Crocodile Shears
1999-05-14 Issued
National Bureau of Machinery Industry
2000-01-01 Implementation
JB9956—1999
This standard is a revision of ZBJ62010-87 "Accuracy of Crocodile Shears". The technical content of this standard is basically the same as that of ZBJ6201087, only the relevant provisions have been re-edited. This standard will be implemented on January 1, 2000.
This standard replaces ZBJ62010—87 from the date of implementation. This standard was proposed and managed by the National Technical Committee for Standardization of Forging Machines. The responsible drafting units of this standard are: Jinan Foundry and Forging Machinery Research Institute, Shenyang Press Tool Factory. This standard was first issued in April 1987.
Machinery Industry Standard of the People's Republic of China
Accuracy of Alligator Shears
This standard specifies the accuracy and inspection method of alligator shears. JB 956-1999bzxZ.net
Generation J287
This standard applies to mechanical transmission alligator shears (hereinafter referred to as shears) for cold shearing metal carbon materials (the tensile strength of the sheared material shall not be greater than 5D0MPa)
2 General requirements
2.1 The requirements for the accuracy inspection of shears shall comply with the relevant provisions of the forging and pressing machinery accuracy inspection. 2.2 Before the precision test, the installation level of the shearing machine should be adjusted. The vertical and horizontal installation level should not be greater than 0.10/1000. 2.3 The precision difference of the test items should be calculated based on the actual test length. If the calculation result is less than or equal to 0.005mm, it will be ignored. If it is greater than 0.005mm, it will be calculated as 0.01mm.
2.4 The standard test sequence does not represent the actual test sequence. For the convenience of assembly and disassembly of test tools and test forces, the test can be carried out in any order.
Approved by the State Machinery Industry Bureau on May 14, 1999 and implemented on January 1, 2000
J8/T9956-1999
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.