JB/T 3016-2004 Technical requirements for rolling bearing packaging boxes
Some standard content:
fcs21 1nG.20
Mechanical Industry Standard of the People's Republic of China
JB/T3016—2004
Generation JB.T3016—1991
JBT3017—1991
Rolling Bearing
Packing Box
Technical Conditions
Rolling bcaringsPackagingboxSpecificatious2004-02-10Issued
2004-06-01Implemented
The National Development and Reform Commission of the People's Republic of ChinaIssuedForeword
Normative references
Terms and definitions
Technical requirements
Marking for confined goods and blocked transportation
Acceptance rules
Sales packaging
Thanks for recordingInformative appendix: Dimensions and specifications of cartons
JR/T3016-2004
JB/T30162004
This standard replaces 3016-19 January 91 Bearing Packaging Needle Box Conditions 3 and B317-1F1 Rolling Bearing Packing Carton Technical Parts
Compared with JR/T31-1991 and JH3-17-1991, the main changes are as follows: the two standards are combined, and the standard name is changed. The cover and name of the 1991 edition and this edition are changed: 1. The requirements for calcium transport boxes are added (Chapters 1, 2, 4, 5, 6.7 of this edition); Chapter 3 "Terms and Definitions" (Chapter 4.1.4 of this edition) are added; 2. The requirements for packaging materials are added (Chapter 5.6 of this edition); 3. The requirements for recycling and reuse marks of packaging items are added (Chapter 5.6 of this edition); 4. The requirements for sales packaging are added (Chapter 6.7 of this edition); 5. The requirements for sales packaging are changed (Chapter 7.1 of this edition); 6. The requirements for sales packaging are changed (Chapter 7.1 of this edition); 7. Chapter 5 and Chapter 6 (Chapter 5 and 6 of this edition, Chapter 6 and 7 of the 1991 edition): Deleted Appendix A of the two standards (Appendix A of the 1991 edition): Used Appendix A in JB/T2013-191 as Appendix A of this standard (Appendix A of this edition, Appendix A of JB/T3017-1991). Appendix A of this standard is an informative appendix. This standard was proposed by China Machinery Industry Federation. This standard was organized by the Standardization Technical Committee of the Ministry of Machinery Industry (CSRTSTC98). The original unit of this standard is Luoyang Bearing Research Institute. The main drafter of this standard is Guo Baodu. The versions replaced by this standard are as follows: - JR3016-1981, JB/T3016-1991: JB3017-1981, JD/T3017-1991. 1 Scope
Technical conditions for rolling bearing packaging boxes
JB/T3016-2004
This standard specifies the technical requirements, delivery conditions, acceptance rules, sales packaging, and the recycling and reuse of packaging materials for corrugated paper boxes, ordinary paper boxes and calcium plastic boxes (hereinafter referred to as paper boxes, wooden boxes and calcium plastic boxes) used for the outer packaging of rolling bearings.
This standard is applied to the outer diameter of domestically sold bearings and commodity parts with a half-year anti-rust period and a year anti-rust period.
It is mainly used for manufacturers, purchasers and bearing users to accept the quality of packaging and packaging materials. 2 Normative references
The clauses of the underlined documents become the clauses of this standard through the reference of this standard. For documents with a date in the past, their subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, all parties that reach an agreement based on this standard are encouraged to use the latest versions of these documents. For undated references, the latest version applies to this standard. Gn:T153-1995 Needlewood Sawn TimberbZxz.net
1551995 Source (E91504473:1988) IR1912M Packaging Storage and Transportation Pictorial Marking (C915078:1907 GD1931-1441 Determination of Wood Moisture Content (A01503:3:1975) Packaging Terminology
GD/T 4122 1 1996
GD/T 4122.2—196
(iB/T4122.3—199?
GH/I4R21--1995
GB/T4BS7.3—1992
GB/T4857.5—1992
GR/T6388—1986
GB/T6543—1986
GB.T6S44—1999
GT/T6980—1995
(B/:7250—1999
Terms of dressing
Packing without language protection
Brocade embedded (eqviSo1029:1974
Packaging transport package static load stacking Acid test method (egV1S2271: 19%5) Packaging and transportation package drop test piece (eqV[S0224B: 1985 Transportation packaging receipt and delivery mark
Wabao paper box
Packing material Wabao paperboard (neg[TS7.1.516: 1997) Calcium plastic corrugated box
European water packaging
GR/T85972007
Rolling beat for rust-proof packaging
Sales packaging section introduction procedure
GB/T12121
GB/113384—1992 General technical conditions for packaging of electromechanical productsGH18455—2031
Packaging receipt mark
Steel belt for packaging
YB/T 03S----Z003
YD5002—1993—General purpose return order (m13IN15441151:19733 Terms and definitions
GB/4122.11996, GB/T1122.2—1996, GB/T4122.3—1996 The terms and definitions established in this standard apply:
FB/ T3016—2004
4 Technical requirements
4.1 Materials and physical properties
4.1.1 Carton
4.1.1.1 Carton inner and outer layers are made of 360g/m*-120gm* kraft board; the middle layer is made of 18Ug*2 kraft board; the corrugated board is made of 1/1 base paper and kraft board and corrugated board of equivalent quality. 4.1.12 The physical properties of corrugated board are in accordance with the provisions of Table 1. Table 1
Category items
Teaching dance welcoming people
4.1.1.3 The area of poor bonding or degumming bubbles of corrugated board does not exceed 0% of the table area. 4.1.1.4 The handling performance indicators of cartons when they are shipped out shall be in accordance with the provisions of Table 2. 4.1.1.5 Other requirements for the following cardboards shall be in accordance with the requirements for Type B in B/6544-1999. Items
Water content
12%12%
10 (plus 1
, suitable for paper frost less than 700mm. 4.1.2 Calcium plastic tile surface should be flat, tile straight, uniform spacing, the base color of the product is not the same, the material performance indicators and other requirements shall comply with the provisions of GB/T6980-1995. 4.1.3 Wood glue
4.1.3.1 The material of this board is coniferous long pin or soft miscellaneous wood. 4.1.3.2 The moisture content of the box board is 12%--25%, and the moisture content is determined according to the provisions of GB/T193/-1995. 4.1.3.3 The box board shall not be rotten, dead, corrugated, late, or damaged. The color and texture of the wood shall not be changed, and the meaning and delivery of the wood shall be in accordance with B/T153-1995, B/155-1995, GR/4823-1995 and GE/113384-142. 4.1.3.4 Other sawn wood with similar physical and mechanical properties to the wood mentioned above may also be used. 4.1.4 Other materials for packaging
Packing boxes are also made of other materials that have been proven to be reliable through tests, or of two or more effective materials, such as metal mesh and other materials.
4.2 Box type
4.2.1 Wooden box
The box type is preferably a 10-type shrink box or an H-type braided box. According to the different modes of transportation, other types may also be used:
4.2.2 Carton
Line plastic type one R/T6543-1986 stipulates $2R)? The basic type of non-woven box is 0U1JB/T3016-2G04
Figure 3, you can use the box type shown in Figures 4 and 5 or other box types as needed, and add the seals and pads shown in the figure to increase the compression resistance and facilitate stacking. Under normal circumstances, Figure 3 is lined and up and down, Figure 4 is paired, and Figure 5 is drawn. The size specifications of paper boxes refer to requirement A:
4.2.3 Plastic boxes
Plastic boxes should adopt Class B boxes specified in GB.T6980-1995, which is the same as the box type of paper. 4.3 Box making requirements
4.3.1 Paper
4.3.1.t The internal size tolerance of paper is specified as -2mm*-+5mm. 4.3.1.2 The low-carbon steel flat wire with chain layer is used for binding cartons. The wire should not have rust spots, peeling, cracking or other defects.
4.3.1.3 The pin joints should be nailed together, and the overlap width should be greater than 35mm1. The pins should be placed along the center line of the overlapped part, and the vertical edge of the box should be 45 degrees. The box nails should be arranged evenly and evenly, and the distance between a single row of nails should not be greater than 80mmR1. The distance between the first nail and the bottom edge should not be greater than 201: The nailed joints should be nailed together, and there should be no defects such as overlapping nails, warped nails, and corners. 431.4 The cut parts and folded parts of each surface of the box should be true angles to each other. When processing the indentation line, the surface of the tile should not be damaged, and there should be no obvious depression on the surface of the cut mouth.
4.3.1.5 The corners of the paper pins should not have a corner, and the diameter of the hole should not be greater than /5mm4.3.1.6 The surface of the carton should not have obvious damage and stains. The length of the carton stop mark is greater than 17m1H1: there should be no cracks or broken lines, and there should be no extra pressure lines on the carton wall. 4.3.1.7
4.3.1.8 The carton ends are opened and closed 180 degrees back and forth for more than 5 times, and there should be no broken parts on the surface layer and the inner layer. 4.3.1.9 The carton is printed with the logo specified in Article 5, and the logo should be accurate, the mark should be clear and neat, and the color should not be too dark. After printing, the outer surface of the carton should be treated with moisture-proof agent.
4.3.2 Calcium plastic box
The requirements for the production of calcium plastic boxes shall comply with the specifications of GB/T 6080-1995. 4.3.3 Wooden box
4.3.3.1 The thickness of each baffle and box of this box is 15mm. For wooden boxes with a gross weight of less than 20kh, the thickness of the board box is 12m. The thickness tolerance is in accordance with the provisions of GB/T153-1995. 4.3.3.2 When making and selling, the board should be matched with the angle, the inclination should not exceed 2mm, the narrowest board should be placed in the middle of other boards, the width of the board should not be less than 40m1r, the number of equal pieces should not be less than 1 piece, and the board width should not exceed 15mm. The length tolerance of the staggered board is 0mm~+3mm. 4.3.3.3 The baffle should be perpendicular to the line around the box: the width of the baffle is 40mm: the height of the baffle is 5Umm. 4.3.3.4 When nailing, the nails should be nailed in the middle, the needle tip should not have a head, the nail distance is 40mm80mm, double row staggered 3
JR/T3016-20D4
, no missing, steel nails are selected according to YR502-1993, the length of the steel nail is 2 times the thickness of the single board plus 7mm-15m14.3.3.5 For wooden box boards, the baffle does not need to be cut, and the depth of the saw marks should not exceed 1mm. The surface accuracy of the front box board is based on the spraying and packaging mark:
4.3.3.6 The internal size tolerance of the box is not changed, and other requirements are determined according to the design drawings. 4.4 Packing requirements
4.4.1 Products that have passed the inspection shall be packed in the inner packaging according to the provisions of (1R/T8597-2003, and the products with qualified inner packaging shall be packed in the outer packaging.
4.4.2 The gross weight of cartons and boxes shall not exceed 25kg, and the gross weight of boxes shall not exceed 30kg. 4.4.3 Bearing products shall be packed in accordance with waterproof requirements. Cartons and anti-smoking boxes shall be lined with plastic bags, and wooden boxes shall be lined with a thin layer of 120g/m2 oil-sprayed sound paper or other waterproof materials. The inner seal shall be on the box wall 1: It should be able to prevent water vapor, and the thickness shall not be less than 60mm .
444, Load the bearing products into the box according to the specified quantity, and fill the gaps with dry and harmless objects such as paper blocks and paper scraps. Other requirements shall be specified in G0.T7350-1999.
425 The packing is completed and the inspection is passed before sealing. After sealing, the cartons and boxes should be tied with plastic tape or tempered plastic tape as shown in the figure. The width of the plastic tape should not be less than 18mm, and the number of strappings can be increased appropriately: the material tape must be tied firmly with the baler. The cartons and plastic tape should not be returned during packaging. The wooden boxes should be tied at the positions shown in Figures 1 and 2. They should be slid to the bottom of the box. The plastic tape should be tied with the baler as shown in Figures 1 and 2. There should be no less than two steel strips, and the width of the steel strip should not be less than 16mm. Steel parts cannot be placed on the box. The steel strips should be in accordance with the provisions of YD.1025-2002:
4.4.6 Other packaging types can also be used. Other packaging types should adopt corresponding measures. If necessary, edge protection and protective cloth can be added to the corners of the box. The protective strips and corners can be made of metal, plastic, etc.: 4.4.7 The packaging should be certified to be shipped from the month, under normal storage conditions, within 12 days, the packaging will not fall off and cause damage to the product. 5. Goods and storage and transportation marks
5.1 After the product is packed, multiple boxes of products from the same subscriber can be checked. No., if the number is expressed as a fraction, the numerator is the box size, the denominator is the total box number, each box should be loaded with the same model of products (if the subscriber agrees on the width, they can be mixed). 5.2 When shipping, the items printed on the front of the carton or plastic box in advance should be sprayed or written with black ink or other non-fading and non-falling paint. The shipping and storage and transportation marks should be sprayed or written neatly. The markings should be in accordance with the provisions of GB/16388-1986, and the main contents are: 1) Product name, model and quantity:
2) Packing size (length × width × height): 3) Net weight or gross weight:
4) Destination (port) and receiving unit:
5) Shipping station (port) Shipping unit:
Factory: Name:
Factory Date.
5.3 The surface of the plastic box is easy to slip, and corresponding anti-slip measures should be taken. The stacking height should not exceed 1.5m. 5.4 The packaging should be sprayed with commodity classification marks, and the format of the marks should comply with the provisions of GB/6388. 5.5 The storage and transportation marks should be in accordance with the provisions of GB/T191-2000, and should be marked with "afraid of moisture" and "careful to place". The marks should be painted on the side or side of the packaging box.
5.6 If the packaging can be reused or recycled, the name, graphic, code, size and use method of the mark shall be determined according to 8184554
211.
6 Acceptance rules
JR/T301G.-20C4
6.! The customer shall inspect the finished boxes according to the provisions of this standard or product samples and the contract. Only qualified boxes can be used for loading: 6.2 The inspection items of the boxes are divided into two categories: one is fatal defects, such as size difference, cracks, cracks, lack of materials, etc.; the other is appearance defects, such as missing parts, exposed tips and cylinder heads, calcium skew, etc. B.3 The customer has the right to re-check the test items in Table 1 and Table 2, the number of which is 2-5 pieces. If the items are unqualified, remedial measures or other measures shall be taken.
6.4 The inspection items of plastic boxes shall comply with the provisions of GB/T6969-1995. B.5 Inspection items: According to the standard, the number of unqualified items is 125 pieces, and the number of unqualified items allowed for the first type of defects is 8: The number of unqualified items allowed for the first type of defects is 1%: According to the standard, the number of unqualified items allowed for the first type of defects is 32 pieces per thousand pieces, and the number of unqualified items allowed is 3. The packaging box shall comply with the provisions of B/T6980-1995. 6.6 When the packaging box is designed with new packaging materials or the user has requirements, it should be inspected according to the provisions of iH/4857.3-192: (/14857.5-1992).
Disposal packaging
Disposal packaging shall be in accordance with the provisions of G12123.
JD/T301620Q4
Appendix A
(Informative)
Dimensions of cartons
A.1 When transporting in packing units, the recommended dimensions of the cartons are as follows: a) 400mm×200mm:
h/300mm×20 0mm:
c)1immX133mm1
c:300mmX10lmm:
e)200mmX150rm
f:200mm×133mm:
When the container unit is not used for transportation, the design principles of the carton size are as follows: A.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of undesired weight, increase the length and reduce the height as much as possible to increase the positive force: - Keep the length-to-width ratio as much as possible, 06 or so, so that the appearance is beautiful and the stacking is stable.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of unweighted, increase the length as much as possible and reduce the height to increase the positive force: - Keep the length-to-width ratio as much as possible, so that the appearance is beautiful and the stacking is stable.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of unweighted, increase the length as much as possible and reduce the height to increase the positive force: - Keep the length-to-width ratio as much as possible, so that the appearance is beautiful and the stacking is stable.3 Plastic boxes
Plastic boxes should be Class B boxes specified in GB.T6980-1995, which is the same as the box type of paper. 4.3 Box making requirements
4.3.1 Paper
4.3.1.t The internal size tolerance of paper is -2mm*-+5mm. 4.3.1.2 The carton boxes should be made of low-carbon steel flat wire with a layer of chain. The wire should not have rust spots, peeling, cracking or other defects.
4.3.1.3 The pin joints should be nailed together, and the overlap width should be greater than 35mm1. The pins should be placed along the center line of the overlapped part, and the vertical edge of the box should be 45 degrees. The box nails should be arranged evenly and evenly, and the distance between a single row of nails should not be greater than 80mmR1. The distance between the first nail and the bottom edge should not be greater than 201: The nailed joints should be nailed together, and there should be no defects such as overlapping nails, warped nails, and corners. 431.4 The cut parts and folded parts of each surface of the box should be true angles to each other. When processing the indentation line, the surface of the tile should not be damaged, and there should be no obvious depression on the surface of the cut mouth.
4.3.1.5 The corners of the paper pins should not have a corner, and the diameter of the hole should not be greater than /5mm4.3.1.6 The surface of the carton should not have obvious damage and stains. The length of the carton stop mark is greater than 17m1H1: there should be no cracks or broken lines, and there should be no extra pressure lines on the carton wall. 4.3.1.7
4.3.1.8 The carton ends are opened and closed 180 degrees back and forth for more than 5 times, and there should be no broken parts on the surface layer and the inner layer. 4.3.1.9 The carton is printed with the logo specified in Article 5, and the logo should be accurate, the mark should be clear and neat, and the color should not be too dark. After printing, the outer surface of the carton should be treated with moisture-proof agent.
4.3.2 Calcium plastic box
The requirements for the production of calcium plastic boxes shall comply with the specifications of GB/T 6080-1995. 4.3.3 Wooden box
4.3.3.1 The thickness of each baffle and box of this box is 15mm. For wooden boxes with a gross weight of less than 20kh, the thickness of the board box is 12m. The thickness tolerance is in accordance with the provisions of GB/T153-1995. 4.3.3.2 When making and selling, the board should be matched with the angle, the inclination should not exceed 2mm, the narrowest board should be placed in the middle of other boards, the width of the board should not be less than 40m1r, the number of equal pieces should not be less than 1 piece, and the board width should not exceed 15mm. The length tolerance of the staggered board is 0mm~+3mm. 4.3.3.3 The baffle should be perpendicular to the line around the box: the width of the baffle is 40mm: the height of the baffle is 5Umm. 4.3.3.4 When nailing, the nails should be nailed in the middle, the needle tip should not have a head, the nail distance is 40mm80mm, double row staggered 3
JR/T3016-20D4
, no missing, steel nails are selected according to YR502-1993, the length of the steel nail is 2 times the thickness of the single board plus 7mm-15m14.3.3.5 For wooden box boards, the baffle does not need to be cut, and the depth of the saw marks should not exceed 1mm. The surface accuracy of the front box board is based on the spraying and packaging mark:
4.3.3.6 The internal size tolerance of the box is not changed, and other requirements are determined according to the design drawings. 4.4 Packing requirements
4.4.1 Products that have passed the inspection shall be packed in the inner packaging according to the provisions of (1R/T8597-2003, and the products with qualified inner packaging shall be packed in the outer packaging.
4.4.2 The gross weight of cartons and boxes shall not exceed 25kg, and the gross weight of boxes shall not exceed 30kg. 4.4.3 Bearing products shall be packed in accordance with waterproof requirements. Cartons and anti-smoking boxes shall be lined with plastic bags, and wooden boxes shall be lined with a thin layer of 120g/m2 oil-sprayed sound paper or other waterproof materials. The inner seal shall be on the box wall 1: It should be able to prevent water vapor, and the thickness shall not be less than 60mm .
444, Load the bearing products into the box according to the specified quantity, and fill the gaps with dry and harmless objects such as paper blocks and paper scraps. Other requirements shall be specified in G0.T7350-1999.
425 The packing is completed and the inspection is passed before sealing. After sealing, the cartons and boxes should be tied with plastic tape or tempered plastic tape as shown in the figure. The width of the plastic tape should not be less than 18mm, and the number of strappings can be increased appropriately: the material tape must be tied firmly with the baler. The cartons and plastic tape should not be returned during packaging. The wooden boxes should be tied at the positions shown in Figures 1 and 2. They should be slid to the bottom of the box. The plastic tape should be tied with the baler as shown in Figures 1 and 2. There should be no less than two steel strips, and the width of the steel strip should not be less than 16mm. Steel parts cannot be placed on the box. The steel strips should be in accordance with the provisions of YD.1025-2002:
4.4.6 Other packaging types can also be used. Other packaging types should adopt corresponding measures. If necessary, edge protection and protective cloth can be added to the corners of the box. The protective strips and corners can be made of metal, plastic, etc.: 4.4.7 The packaging should be certified to be shipped from the month, under normal storage conditions, within 12 days, the packaging will not fall off and cause damage to the product. 5. Goods and storage and transportation marks
5.1 After the product is packed, multiple boxes of products from the same subscriber can be checked. No., if the number is expressed as a fraction, the numerator is the box size, the denominator is the total box number, each box should be loaded with the same model of products (if the subscriber agrees on the width, they can be mixed). 5.2 When shipping, the items printed on the front of the carton or plastic box in advance should be sprayed or written with black ink or other non-fading and non-falling paint. The shipping and storage and transportation marks should be sprayed or written neatly. The markings should be in accordance with the provisions of GB/16388-1986, and the main contents are: 1) Product name, model and quantity:
2) Packing size (length × width × height): 3) Net weight or gross weight:
4) Destination (port) and receiving unit:
5) Shipping station (port) Shipping unit:
Factory: Name:
Factory Date.
5.3 The surface of the plastic box is easy to slip, and corresponding anti-slip measures should be taken. The stacking height should not exceed 1.5m. 5.4 The packaging should be sprayed with commodity classification marks, and the format of the marks should comply with the provisions of GB/6388. 5.5 The storage and transportation marks should be in accordance with the provisions of GB/T191-2000, and should be marked with "afraid of moisture" and "careful to place". The marks should be painted on the side or side of the packaging box.
5.6 If the packaging can be reused or recycled, the name, graphic, code, size and use method of the mark shall be determined according to 8184554
211.
6 Acceptance rules
JR/T301G.-20C4
6.! The customer shall inspect the finished boxes according to the provisions of this standard or product samples and the contract. Only qualified boxes can be used for loading: 6.2 The inspection items of the boxes are divided into two categories: one is fatal defects, such as size difference, cracks, cracks, lack of materials, etc.; the other is appearance defects, such as missing parts, exposed tips and cylinder heads, calcium skew, etc. B.3 The customer has the right to re-check the test items in Table 1 and Table 2, the number of which is 2-5 pieces. If the items are unqualified, remedial measures or other measures shall be taken.
6.4 The inspection items of plastic boxes shall comply with the provisions of GB/T6969-1995. B.5 Inspection items: According to the standard, the number of unqualified items is 125 pieces, and the number of unqualified items allowed for the first type of defects is 8: The number of unqualified items allowed for the first type of defects is 1%: According to the standard, the number of unqualified items allowed for the first type of defects is 32 pieces per thousand pieces, and the number of unqualified items allowed is 3. The packaging box shall comply with the provisions of B/T6980-1995. 6.6 When the packaging box is designed with new packaging materials or the user has requirements, it should be inspected according to the provisions of iH/4857.3-192: (/14857.5-1992).
Disposal packaging
Disposal packaging shall be in accordance with the provisions of G12123.
JD/T301620Q4
Appendix A
(Informative)
Dimensions of cartons
A.1 When transporting in packing units, the recommended dimensions of the cartons are as follows: a) 400mm×200mm:
h/300mm×20 0mm:
c)1immX133mm1
c:300mmX10lmm:
e)200mmX150rm
f:200mm×133mm:
When the container unit is not used for transportation, the design principles of the carton size are as follows: A.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of undesired weight, increase the length and reduce the height as much as possible to increase the positive force: - Keep the length-to-width ratio as much as possible, 06 or so, so that the appearance is beautiful and the stacking is stable.3 Plastic boxes
Plastic boxes should be Class B boxes specified in GB.T6980-1995, which is the same as the box type of paper. 4.3 Box making requirements
4.3.1 Paper
4.3.1.t The internal size tolerance of paper is -2mm*-+5mm. 4.3.1.2 The carton boxes should be made of low-carbon steel flat wire with a layer of chain. The wire should not have rust spots, peeling, cracking or other defects.
4.3.1.3 The pin joints should be nailed together, and the overlap width should be greater than 35mm1. The pins should be placed along the center line of the overlapped part, and the vertical edge of the box should be 45 degrees. The box nails should be arranged evenly and evenly, and the distance between a single row of nails should not be greater than 80mmR1. The distance between the first nail and the bottom surface should not be greater than 201: The nailed joints should be nailed together, and there should be no defects such as overlapping nails, warped nails, and corners. 431.4 The cut parts and folded parts of each surface of the box should be true angles to each other. When processing the indentation line, the surface of the tile should not be damaged, and there should be no obvious depressions on the surface of the cut mouth.
4.3.1.5 The corners of the paper pins should not have corners, and the diameter of the holes should not be greater than /5mm4.3.1.6 The surface of the carton should not have obvious damage and stains. The length of the carton stop mark is greater than 17m1H1: there should be no cracks or broken lines, and there should be no extra pressure lines on the carton wall. 4.3.1.7
4.3.1.8 The carton ends are opened and closed 180 degrees back and forth for more than 5 times, and there should be no broken parts on the surface layer and the inner layer. 4.3.1.9 The carton is printed with the logo specified in Article 5, and the logo should be accurate, the mark should be clear and neat, and the color should not be too dark. After printing, the outer surface of the carton should be treated with moisture-proof agent.
4.3.2 Calcium plastic box
The requirements for the production of calcium plastic boxes shall comply with the specifications of GB/T 6080-1995. 4.3.3 Wooden box
4.3.3.1 The thickness of each baffle and box of this box is 15mm. For wooden boxes with a gross weight of less than 20kh, the thickness of the board box is 12m. The thickness tolerance is in accordance with the provisions of GB/T153-1995. 4.3.3.2 When making and selling, the board should be matched with the angle, the inclination should not exceed 2mm, the narrowest board should be placed in the middle of other boards, the width of the board should not be less than 40m1r, the number of equal pieces should not be less than 1 piece, and the board width should not exceed 15mm. The length tolerance of the staggered board is 0mm~+3mm. 4.3.3.3 The baffle should be perpendicular to the line around the box: the width of the baffle is 40mm: the height of the baffle is 5Umm. 4.3.3.4 When nailing, the nails should be nailed in the middle, the needle tip should not have a head, the nail distance is 40mm80mm, double row staggered 3
JR/T3016-20D4
, no missing, steel nails are selected according to YR502-1993, the length of the steel nail is 2 times the thickness of the single board plus 7mm-15m14.3.3.5 For wooden box boards, the baffle does not need to be cut, and the depth of the saw marks should not exceed 1mm. The surface accuracy of the front box board is based on the spraying and packaging mark:
4.3.3.6 The internal size tolerance of the box is not changed, and other requirements are determined according to the design drawings. 4.4 Packing requirements
4.4.1 Products that have passed the inspection shall be packed in the inner packaging according to the provisions of (1R/T8597-2003, and the products with qualified inner packaging shall be packed in the outer packaging.
4.4.2 The gross weight of cartons and boxes shall not exceed 25kg, and the gross weight of boxes shall not exceed 30kg. 4.4.3 Bearing products shall be packed in accordance with waterproof requirements. Cartons and anti-smoking boxes shall be lined with plastic bags, and wooden boxes shall be lined with a thin layer of 120g/m2 oil-sprayed sound paper or other waterproof materials. The inner seal shall be on the box wall 1: It should be able to prevent water vapor, and the thickness shall not be less than 60mm .
444, Load the bearing products into the box according to the specified quantity, and fill the gaps with dry and harmless objects such as paper blocks and paper scraps. Other requirements shall be specified in G0.T7350-1999.
425 The packing is completed and the inspection is passed before sealing. After sealing, the cartons and boxes should be tied with plastic tape or tempered plastic tape as shown in the figure. The width of the plastic tape should not be less than 18mm, and the number of strappings can be increased appropriately: the material tape must be tied firmly with the baler. The cartons and plastic tape should not be returned during packaging. The wooden boxes should be tied at the positions shown in Figures 1 and 2. They should be slid to the bottom of the box. The plastic tape should be tied with the baler as shown in Figures 1 and 2. There should be no less than two steel strips, and the width of the steel strip should not be less than 16mm. Steel parts cannot be placed on the box. The strips should be in accordance with the provisions of YD.1025-2002:
4.4.6 Other packaging types can also be used. Other packaging types should adopt corresponding measures. If necessary, edge protection and protective cloth can be added to the corners of the box. The protective strips and corners can be made of metal, plastic, etc.: 4.4.7 The packaging should be certified to be shipped from the month, under normal storage conditions, within 12 days, the packaging will not fall off and cause damage to the product. 5. Goods and storage and transportation marks
5.1 After the product is packed, multiple boxes of products from the same subscriber can be checked. No., if the number is expressed as a fraction, the numerator is the box size, the denominator is the total box number, each box should be loaded with the same model of products (if the subscriber agrees on the width, they can be mixed). 5.2 When shipping, the items printed on the wall or on the front of the carton and plastic box in advance should be sprayed or written with black ink or other non-fading and non-falling paint. The shipping and storage and transportation marks shall be sprayed or written neatly. The markings shall be in accordance with the provisions of GB/16388-1986, and the main contents are: 1) Product name, model and quantity:
2) Packing size (length × width × height): 3) Net weight or gross weight:
4) Destination (port) and receiving unit:
5) Shipping station (port) Shipping unit:
Factory: Name:
Factory Date.
5.3 The surface of the plastic box is easy to slip, and corresponding anti-slip measures should be taken. The stacking height should not exceed 1.5m. 5.4 The packaging should be sprayed with commodity classification marks, and the format of the marks should comply with the provisions of GB/6388. 5.5 The storage and transportation marks should be in accordance with the provisions of GB/T191-2000, and should be marked with "afraid of moisture" and "careful to place". The marks should be painted on the side or side of the packaging box.
5.6 If the packaging can be reused or recycled, the name, graphic, code, size and use method of the mark shall be determined according to 8184554
211.
6 Acceptance rules
JR/T301G.-20C4
6.! The customer shall inspect the finished boxes according to the provisions of this standard or product samples and the contract. Only qualified boxes can be used for loading: 6.2 The inspection items of the boxes are divided into two categories: one is fatal defects, such as size difference, cracks, cracks, lack of materials, etc.; the other is appearance defects, such as missing parts, exposed tips and cylinder heads, calcium skew, etc. B.3 The customer has the right to re-check the test items in Table 1 and Table 2, the number of which is 2-5 pieces. If the items are unqualified, remedial measures or other measures shall be taken.
6.4 The inspection items of plastic boxes shall comply with the provisions of GB/T6969-1995. B.5 Inspection items: According to the standard, the number of unqualified items is 125 pieces, and the number of unqualified items allowed for the first type of defects is 8: The number of unqualified items allowed for the first type of defects is 1%: According to the standard, the number of unqualified items allowed for the first type of defects is 32 pieces per thousand pieces, and the number of unqualified items allowed is 3. The packaging box shall comply with the provisions of B/T6980-1995. 6.6 When the packaging box is designed with new packaging materials or the user has requirements, it should be inspected according to the provisions of iH/4857.3-192: (/14857.5-1992).
Disposal packaging
Disposal packaging shall be in accordance with the provisions of G12123.
JD/T301620Q4
Appendix A
(Informative)
Dimensions of cartons
A.1 When transporting in packing units, the recommended dimensions of the cartons are as follows: a) 400mm×200mm:
h/300mm×20 0mm:
c)1immX133mm1
c:300mmX10lmm:
e)200mmX150rm
f:200mm×133mm:
When the container unit is not used for transportation, the design principles of the carton size are as follows: A.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of undesired weight, increase the length and reduce the height as much as possible to increase the positive force: - Keep the length-to-width ratio as much as possible, 06 or so, so that the appearance is beautiful and the stacking is stable.3. The pin joints should be nailed together, and the overlap width should be greater than 35mm1. The pins should be placed along the center line of the overlapped part, and the vertical edge of the box should be 45 degrees. The box nails should be arranged evenly and evenly, and the distance between a single row of nails should not be greater than 80mm. The distance between the first nail and the bottom surface should not be greater than 201: The nailed joints should be nailed together, and there should be no defects such as overlapping nails, warped nails, and corners. 4.3.1.4 The cut parts and folded parts of each surface of the box should be true angles to each other. When processing the indentation line, the surface of the tile should not be damaged, and there should be no obvious depressions on the surface of the cut mouth.
4.3.1.5 The corners of the paper pins should not have corners, and the diameter of the holes should not be greater than /5mm4.3.1.6 The surface of the carton should not have obvious damage and stains. The length of the carton stop mark is greater than 17m1H1: there should be no cracks or broken lines, and there should be no extra pressure lines on the carton wall. 4.3.1.7
4.3.1.8 The carton ends are opened and closed 180 degrees back and forth for more than 5 times, and there should be no broken parts on the surface layer and the inner layer. 4.3.1.9 The carton is printed with the logo specified in Article 5, and the logo should be accurate, the mark should be clear and neat, and the color should not be too dark. After printing, the outer surface of the carton should be treated with moisture-proof agent.
4.3.2 Calcium plastic box
The requirements for the production of calcium plastic boxes shall comply with the specifications of GB/T 6080-1995. 4.3.3 Wooden box
4.3.3.1 The thickness of each baffle and box of this box is 15mm. For wooden boxes with a gross weight of less than 20kh, the thickness of the board box is 12m. The thickness tolerance is in accordance with the provisions of GB/T153-1995. 4.3.3.2 When making and selling, the board should be matched with the angle, the inclination should not exceed 2mm, the narrowest board should be placed in the middle of other boards, the width of the board should not be less than 40m1r, the number of equal pieces should not be less than 1 piece, and the board width should not exceed 15mm. The length tolerance of the staggered board is 0mm~+3mm. 4.3.3.3 The baffle should be perpendicular to the line around the box: the width of the baffle is 40mm: the height of the baffle is 5Umm. 4.3.3.4 When nailing, the nails should be nailed in the middle, the needle tip should not have a head, the nail distance is 40mm80mm, double row staggered 3
JR/T3016-20D4
, no missing, steel nails are selected according to YR502-1993, the length of the steel nail is 2 times the thickness of the single board plus 7mm-15m14.3.3.5 For wooden box boards, the baffle does not need to be cut, and the depth of the saw marks should not exceed 1mm. The surface accuracy of the front box board is based on the spraying and packaging mark:
4.3.3.6 The internal size tolerance of the box is not changed, and other requirements are determined according to the design drawings. 4.4 Packing requirements
4.4.1 Products that have passed the inspection shall be packed in the inner packaging according to the provisions of (1R/T8597-2003, and the products with qualified inner packaging shall be packed in the outer packaging.
4.4.2 The gross weight of cartons and boxes shall not exceed 25kg, and the gross weight of boxes shall not exceed 30kg. 4.4.3 Bearing products shall be packed in accordance with waterproof requirements. Cartons and anti-smoking boxes shall be lined with plastic bags, and wooden boxes shall be lined with a thin layer of 120g/m2 oil-sprayed sound paper or other waterproof materials. The inner seal shall be on the box wall 1: It should be able to prevent water vapor, and the thickness shall not be less than 60mm .
444, Load the bearing products into the box according to the specified quantity, and fill the gaps with dry and harmless objects such as paper blocks and paper scraps. Other requirements shall be specified in G0.T7350-1999.
425 The packing is completed and the inspection is passed before sealing. After sealing, the cartons and boxes should be tied with plastic tape or tempered plastic tape as shown in the figure. The width of the plastic tape should not be less than 18mm, and the number of strappings can be increased appropriately: the material tape must be tied firmly with the baler. The cartons and plastic tape should not be returned during packaging. The wooden boxes should be tied at the positions shown in Figures 1 and 2. They should be slid to the bottom of the box. The plastic tape should be tied with the baler as shown in Figures 1 and 2. There should be no less than two steel strips, and the width of the steel strip should not be less than 16mm. Steel parts cannot be placed on the box. The steel strips should be in accordance with the provisions of YD.1025-2002:
4.4.6 Other packaging types can also be used. Other packaging types should adopt corresponding measures. If necessary, edge protection and protective cloth can be added to the corners of the box. The protective strips and corners can be made of metal, plastic, etc.: 4.4.7 The packaging should be certified to be shipped from the month, under normal storage conditions, within 12 days, the packaging will not fall off and cause damage to the product. 5. Goods and storage and transportation marks
5.1 After the product is packed, multiple boxes of products from the same subscriber can be checked. No., if the number is expressed as a fraction, the numerator is the box size, the denominator is the total box number, each box should be loaded with the same model of products (if the subscriber agrees on the width, they can be mixed). 5.2 When shipping, the items printed on the front of the carton or plastic box in advance should be sprayed or written with black ink or other non-fading and non-falling paint. The shipping and storage and transportation marks should be sprayed or written neatly. The markings should be in accordance with the provisions of GB/16388-1986, and the main contents are: 1) Product name, model and quantity:
2) Packing size (length × width × height): 3) Net weight or gross weight:
4) Destination (port) and receiving unit:
5) Shipping station (port) Shipping unit:
Factory: Name:
Factory Date.
5.3 The surface of the plastic box is easy to slip, and corresponding anti-slip measures should be taken. The stacking height should not exceed 1.5m. 5.4 The packaging should be sprayed with commodity classification marks, and the format of the marks should comply with the provisions of GB/6388. 5.5 The storage and transportation marks should be in accordance with the provisions of GB/T191-2000, and should be marked with "afraid of moisture" and "careful to place". The marks should be painted on the side or side of the packaging box.
5.6 If the packaging can be reused or recycled, the name, graphic, code, size and use method of the mark shall be determined according to 8184554
211.
6 Acceptance rules
JR/T301G.-20C4
6.! The customer shall inspect the finished boxes according to the provisions of this standard or product samples and the contract. Only qualified boxes can be used for loading: 6.2 The inspection items of the boxes are divided into two categories: one is fatal defects, such as size difference, cracks, cracks, lack of materials, etc.; the other is appearance defects, such as missing parts, exposed tips and cylinder heads, calcium skew, etc. B.3 The customer has the right to re-check the test items in Table 1 and Table 2, the number of which is 2-5 pieces. If the items are unqualified, remedial measures or other measures shall be taken.
6.4 The inspection items of plastic boxes shall comply with the provisions of GB/T6969-1995. B.5 Inspection items: According to the standard, the number of unqualified items is 125 pieces, and the number of unqualified items allowed for the first type of defects is 8: The number of unqualified items allowed for the first type of defects is 1%: According to the standard, the number of unqualified items allowed for the first type of defects is 32 pieces per thousand pieces, and the number of unqualified items allowed is 3. The packaging box shall comply with the provisions of B/T6980-1995. 6.6 When the packaging box is designed with new packaging materials or the user has requirements, it should be inspected according to the provisions of iH/4857.3-192: (/14857.5-1992).
Disposal packaging
Disposal packaging shall be in accordance with the provisions of G12123.
JD/T301620Q4
Appendix A
(Informative)
Dimensions of cartons
A.1 When transporting in packing units, the recommended dimensions of the cartons are as follows: a) 400mm×200mm:
h/300mm×20 0mm:
c)1immX133mm1
c:300mmX10lmm:
e)200mmX150rm
f:200mm×133mm:
When the container unit is not used for transportation, the design principles of the carton size are as follows: A.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of undesired weight, increase the length and reduce the height as much as possible to increase the positive force: - Keep the length-to-width ratio as much as possible, 06 or so, so that the appearance is beautiful and the stacking is stable.3. The pin joints should be nailed together, and the overlap width should be greater than 35mm1. The pins should be placed along the center line of the overlapped part, and the vertical edge of the box should be 45 degrees. The box nails should be arranged evenly and evenly, and the distance between a single row of nails should not be greater than 80mm. The distance between the first nail and the bottom surface should not be greater than 201: The nailed joints should be nailed together, and there should be no defects such as overlapping nails, warped nails, and corners. 4.3.1.4 The cut parts and folded parts of each surface of the box should be true angles to each other. When processing the indentation line, the surface of the tile should not be damaged, and there should be no obvious depressions on the surface of the cut mouth.
4.3.1.5 The corners of the paper pins should not have corners, and the diameter of the holes should not be greater than /5mm4.3.1.6 The surface of the carton should not have obvious damage and stains. The length of the carton stop mark is greater than 17m1H1: there should be no cracks or broken lines, and there should be no extra pressure lines on the carton wall. 4.3.1.7
4.3.1.8 The carton ends are opened and closed 180 degrees back and forth for more than 5 times, and there should be no broken parts on the surface layer and the inner layer. 4.3.1.9 The carton is printed with the logo specified in Article 5, and the logo should be accurate, the mark should be clear and neat, and the color should not be too dark. After printing, the outer surface of the carton should be treated with moisture-proof agent.
4.3.2 Calcium plastic box
The requirements for the production of calcium plastic boxes shall comply with the specifications of GB/T 6080-1995. 4.3.3 Wooden box
4.3.3.1 The thickness of each baffle and box of this box is 15mm. For wooden boxes with a gross weight of less than 20kh, the thickness of the board box is 12m. The thickness tolerance is in accordance with the provisions of GB/T153-1995. 4.3.3.2 When making and selling, the board should be matched with the angle, the inclination should not exceed 2mm, the narrowest board should be placed in the middle of other boards, the width of the board should not be less than 40m1r, the number of equal pieces should not be less than 1 piece, and the board width should not exceed 15mm. The length tolerance of the staggered board is 0mm~+3mm. 4.3.3.3 The baffle should be perpendicular to the line around the box: the width of the baffle is 40mm: the height of the baffle is 5Umm. 4.3.3.4 When nailing, the nails should be nailed in the middle, the needle tip should not have a head, the nail distance is 40mm80mm, double row staggered 3
JR/T3016-20D4
, no missing, steel nails are selected according to YR502-1993, the length of the steel nail is 2 times the thickness of the single board plus 7mm-15m14.3.3.5 For wooden box boards, the baffle does not need to be cut, and the depth of the saw marks should not exceed 1mm. The surface accuracy of the front box board is based on the spraying and packaging mark:
4.3.3.6 The internal size tolerance of the box is not changed, and other requirements are determined according to the design drawings. 4.4 Packing requirements
4.4.1 Products that have passed the inspection shall be packed in the inner packaging according to the provisions of (1R/T8597-2003, and the products with qualified inner packaging shall be packed in the outer packaging.
4.4.2 The gross weight of cartons and boxes shall not exceed 25kg, and the gross weight of boxes shall not exceed 30kg. 4.4.3 Bearing products shall be packed in accordance with waterproof requirements. Cartons and anti-smoking boxes shall be lined with plastic bags, and wooden boxes shall be lined with a thin layer of 120g/m2 oil-sprayed paper or other waterproof materials. The inner seal shall be on the box wall 1: It should be able to prevent water vapor, and the thickness shall not be less than 60mm .
444, Load the bearing products into the box according to the specified quantity, and fill the gaps with dry and harmless objects such as paper blocks and paper scraps. Other requirements shall be specified in G0.T7350-1999.
425 The packing is completed and the inspection is passed before sealing. After sealing, the cartons and boxes should be tied with plastic tape or tempered plastic tape as shown in the figure. The width of the plastic tape should not be less than 18mm, and the number of strappings can be increased appropriately: the material tape must be tied firmly with the baler. The cartons and plastic tape should not be returned during packaging. The wooden boxes should be tied at the positions shown in Figures 1 and 2. They should be slid to the bottom of the box. The plastic tape should be tied with the baler as shown in Figures 1 and 2. There should be no less than two steel strips, and the width of the steel strip should not be less than 16mm. Steel parts cannot be placed on the box. The strips should be in accordance with the provisions of YD.1025-2002:
4.4.6 Other packaging types can also be used. Other packaging types should adopt corresponding measures. If necessary, edge protection and protective cloth can be added to the corners of the box. The protective strips and corners can be made of metal, plastic, etc.: 4.4.7 The packaging should be certified to be shipped from the month, under normal storage conditions, within 12 days, the packaging will not fall off and cause damage to the product. 5. Goods and storage and transportation marks
5.1 After the product is packed, multiple boxes of products from the same subscriber can be checked. No., if the number is expressed as a fraction, the numerator is the box size, the denominator is the total box number, each box should be loaded with the same model of products (if the subscriber agrees on the width, they can be mixed). 5.2 When shipping, the items printed on the wall or on the front of the carton and plastic box in advance should be sprayed or written with black ink or other non-fading and non-falling paint. The shipping and storage and transportation marks shall be sprayed or written neatly. The markings shall be in accordance with the provisions of GB/16388-1986, and the main contents are: 1) Product name, model and quantity:
2) Packing size (length × width × height): 3) Net weight or gross weight:
4) Destination (port) and receiving unit:
5) Shipping station (port) Shipping unit:
Factory: Name:
Factory Date.
5.3 The surface of the plastic box is easy to slip, and corresponding anti-slip measures should be taken. The stacking height should not exceed 1.5m. 5.4 The packaging should be sprayed with commodity classification marks, and the format of the marks should comply with the provisions of GB/6388. 5.5 The storage and transportation marks should be in accordance with the provisions of GB/T191-2000, and should be marked with "afraid of moisture" and "careful to place". The marks should be painted on the side or side of the packaging box.
5.6 If the packaging can be reused or recycled, the name, graphic, code, size and use method of the mark shall be determined according to 8184554
211.
6 Acceptance rules
JR/T301G.-20C4
6.! The customer shall inspect the finished boxes according to the provisions of this standard or product samples and the contract. Only qualified boxes can be used for loading: 6.2 The inspection items of the boxes are divided into two categories: one is fatal defects, such as size difference, cracks, cracks, lack of materials, etc.; the other is appearance defects, such as missing parts, exposed tips and cylinder heads, calcium skew, etc. B.3 The customer has the right to re-check the test items in Table 1 and Table 2, the number of which is 2-5 pieces. If the items are unqualified, remedial measures or other measures shall be taken.
6.4 The inspection items of plastic boxes shall comply with the provisions of GB/T6969-1995. B.5 Inspection items: According to the standard, the number of unqualified items is 125 pieces, and the number of unqualified items allowed for the first type of defects is 8: The number of unqualified items allowed for the first type of defects is 1%: According to the standard, the number of unqualified items allowed for the first type of defects is 32 pieces per thousand pieces, and the number of unqualified items allowed is 3. The packaging box shall comply with the provisions of B/T6980-1995. 6.6 When the packaging box is designed with new packaging materials or the user has requirements, it should be inspected according to the provisions of iH/4857.3-192: (/14857.5-1992).
Disposal packaging
Disposal packaging should be in accordance with the provisions of G12123.
JD/T301620Q4
Appendix A
(Informative)
Dimensions of cartons
A.1 When transporting in packing units, the recommended dimensions of the cartons are as follows: a) 400mm×200mm:
h/300mm×20 0mm:
c)1immX133mm1
c:300mmX10lmm:
e)200mmX150rm
f:200mm×133mm:
When the container unit is not used for transportation, the design principles of the carton size are as follows: A.2
Based on the size of the contents, make full use of the internal space of the carton as much as possible to reduce filling: - In the case of undesired weight, increase the length and reduce the height as much as possible to increase the positive force: - Keep the length-to-width ratio as much as possible, 06 or so, so that the appearance is beautiful and the stacking is stable.9. The carton shall be printed with the mark specified in Article 5. The mark shall be accurate, clear and neat, and not too dark. After printing, the outer surface of the carton shall be treated with moisture-proof agent.
4.3.2 Calcium plastic carton
The carton making requirements of calcium plastic carton shall comply with the regulations of GB/6080-1995. 4.3.3 Wooden carton
4.3.3.1 The thickness of each baffle and carton of this carton shall be 15mm. The gross weight of the carton is less than 20kh. For wooden carton, the thickness shall be 12mm. The thickness tolerance shall comply with the regulations of GB/T153-1995. 4.3.3.2 When making carton, the matching of the panels shall be in accordance with the angle, the inclination shall not exceed 2mm, the narrowest panel shall be placed in the middle of other panels, the width of the panel shall not be less than 40mm, the number of panels shall not be less than 1 piece, and the thickness of the panel shall not be less than 5mm. The length tolerance of the staggered board is 0mm~+3mm. 4.3.3.3 The baffle should be perpendicular to the line around the box: the width of the baffle is 40mm: the height of the baffle is 5Umm. 4.3.3.4 When nailing, the nails should be nailed in the middle, the needle tip should not have a head, the nail distance is 40mm80mm, double row staggered 3
JR/T3016-20D4
, no missing, steel nails are selected according to YR502-1993, the length of the steel nail is 2 times the thickness of the single board plus 7mm-15m14.3.3.5 For wooden box boards, the baffle does not need to be cut, and the depth of the saw marks should not exceed 1mm. The surface accuracy of the front box board is based on the spraying and packaging mark:
4.3.3.6 The internal size tolerance of the box is not changed, and other requirements are determined according to the design drawings. 4.4 Packing requirements
4.4.1 Products that have passed the inspection shall be packed in the inner packaging according to the provisions of (1R/T8597-2003, and the products with qualified inner packaging shall be packed in the outer packaging.
4.4.2 The gross weight of cartons and boxes shall not exceed 25kg, and the gross weight of boxes shall not exceed 30kg. 4.4.3 Bearing products shall be packed in accordance with waterproof requirements. Cartons and anti-smoking boxes shall be lined with plastic bags, and wooden boxes shall be lined with a thin layer of 120g/m2 oil-sprayed sound paper or other waterproof materials. The inner seal shall be on the box wall 1: It should be able to prevent water vapor, and the thickness shall not be less than 60mm .
444, Load the bearing products into the box according to the specified quantity, and fill the gaps with dry and harmless objects such as paper blocks and paper scraps. Other requirements shall be specified in G0.T7350-1999.
425 The packing is completed and the inspection is passed before sealing. After sealing, the cartons and boxes should be tied with plastic tape or tempered plastic tape as shown in the figure. The width of the plastic tape should not be less than 18mm, and the number of strappings can be increased appropriately: the material tape must be tied firmly with the baler. The cartons and plastic tape should not be returned during packaging. The wooden boxes should be tied at the positions shown in Figures 1 and 2. They should be slid to the bottom of the box. The plastic tape should be tied with the baler as shown in Figures 1 and 2. There should be no less than two steel strips, and the width of the steel strip should not be less than 16mm. Steel parts cannot be placed on the box. The steel strips should be in accordance with the provisions of YD.1025-2002:
4.4.6 Other packaging types can also be used. Other packaging types should adopt corresponding measures. If necessary, edge protection and protective cloth can be added to the corners of the box. The protective strips and corners can be made of metal, plastic, etc.: 4.4.7 The packaging should be certified to be shipped from the month, under normal storage conditions, within 12 days, the packaging will not fall off and cause damage to the product. 5. Goods and storage and transportation marks
5.1 After the product is packed, multiple boxes of products from the same subscriber can be checked. No., if the number is expressed as a fraction, the numerator is the box size, the denominator is the total box number, each box should be loaded with the same model of products (if the subscriber agrees on the width, they can be mixed). 5.2 When shipping, the items printed on the front of the carton or plastic box in advance should be sprayed or written with black ink or other non-fading and non-falling paint. The shipping and storage and transportation marks should be sprayed or written neatly. The markings should be in accordance with the provisions of GB/16388-1986, and the main contents are: 1) Product name, model and quantity:
2) Packing size (length × width × height): 3) Net weight or gross weight:
4) Destination (port) and receiving unit:
5) Shipping station (port) Shipping unit:
Factory: Name:
Factory Date.
5.3 The surface of the plastic box is easy to slip, and corresponding anti-slip measures should be taken. The stacking height should not exceed 1.5m. 5.4 The packaging should be sprayed with commodity classification marks, and the format of the marks should comply with the provisions of GB/6388. 5.5 The storage and transportation marks should be in accordance with the provisions of GB/T191-2000, and should be marked with "afraid of moisture" and "careful to place". The marks should be painted on the side or side of the packaging box.
5.6 If the packaging can be reused or recycled, the name, graphic, code, size and use method of the mark shall be determined according to 8184554
211.
6 Acceptance rules
JR/T301G.-20C4
6.! The customer shall inspect the finished boxes according to the provisions of this standard or product samples and the contract. Only qualified boxes can be used for loading: 6.2 The inspection items of the boxes are divided into two categories: one is fatal defects, such as size difference, cracks, cracks, lack of materials, etc.; the other is appearance defects, such as missing parts, exposed tips and cylinder heads, calcium skew, etc. B.3 The customer has the right to re-check the test items in Table 1 and Table 2, the number of which is 2-5 pieces. If the items are unqualified, remedial measures or other measures shall be taken.
6.4 The inspection items of plastic boxes shall comply with the provisions of GB/T6969-1995. B.5 Inspection items: According to the standard, the number of unqu
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.