This standard specifies the requirements, test methods, inspection rules, marking, packaging, transportation and storage of acetate filter rods. This standard applies to acetate filter rods. GB/T 5605-2002 Tobacco and tobacco products acetate filter rods GB/T5605-2002 Standard download decompression password: www.bzxz.net

ICS65.160
National Standard of the People's Republic of China
GB/T5605--2002
Replaces GB/T5605-1996
Tobacco and tobacco products
Acetate fiber filter rod
Tobacco and tobacco products-Acetate fiber filter rod2002-08-12Promulgated
The People's Republic of China
General Administration of Quality Supervision, Inspection and Quarantine
2003-02-01Implementation
GB/T 5605- 2002
This standard has the following changes to some chapters of GB/T5605--1996 "Acetate Filter Rods for Tobacco and Tobacco Products": the definition of roundness has been modified, the definition of "single sample" has been cancelled, and some definitions have been added; the tolerance value of pressure drop has been reduced, and the pressure drop value is specified to be accurate to 10Pa; the hardness has been changed from "89%" to "according to design requirements"; the moisture has been changed from "≤7%" to "<8.0%"; the roundness has been changed from "≤0.25mm" to "<0.35mm"; the appearance has been listed separately from the "physical indicators of filter rods"; the sampling method of GB2828-1987 "Batch-by-Batch Inspection Count Sampling Procedure and Sampling Table (Applicable to Inspection of Continuous Batch)" has been cancelled. Sampling is divided into two types: delivery inspection and type inspection, and specific methods are specified; the test method adopts the latest industry standards, and the test methods for burst holes and internal bonding lines have been added; and the veto items of the filter rod judgment rules have been added. This standard replaces GB/T5605-1996 "Acetate Fiber Filter Rods for Tobacco and Tobacco Products".
This standard is proposed by the State Tobacco Monopoly Administration. This standard is under the jurisdiction of the National Tobacco Standardization Technical Committee (TC144). The drafting units of this standard are: Science and Education Department of the State Tobacco Monopoly Administration, China Tobacco Material Company, National Tobacco Quality Supervision and Inspection Center, Hubei Tobacco Quality Inspection Station, Nantong Cigarette Filter Experimental Factory, Shandong General Group Jinan Cigarette Factory. The main drafters of this standard are: Yu Mingfang, Xing Jun, Shen Yunlong, Li Qingcheng, Feng Xiaomin, Sheng Peixiu, Liu Jiye. The previous versions of the standards replaced by this standard are: GB 5605-1988;
-GB/T5605-1996.
1 Scope
Tobacco and tobacco products
Acetate filter rods
GB/T 5605--2002
This standard specifies the requirements, test methods, inspection rules, marking, packaging, transportation and storage of acetate filter rods. This standard applies to acetate filter rods (hereinafter referred to as filter rods). 2 Normative references
The clauses in the following documents become the clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, the parties to an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this standard. GB/T8170 Rules for rounding off values
Atmospheric environment for adjustment and testing (idtISO3402) GB/T16447 Tobacco and tobacco products
YC/T37.1 Determination of physical properties of filter rods Part 1: Length photoelectric methodYC/T37.2 Determination of physical properties of filter rods Part 2: Circumferential laser methodYC/T37.3 Determination of physical properties of filter rods Part 3: Absorption resistanceYC/T 37. 4
YC/T 37.5
Part 4: Hardness
Determination of physical properties of filter rods
Determination of physical properties of filter rods
Part 5: Moisture
YC/T37.6. Determination of the physical properties of filter rods Part 6: Roundness
YC/T37.7—1996 Determination of the physical properties of filter rods Part 7: Appearance 3 Terms and definitions
The following terms and definitions apply to this standard. 3.1
Roundness
The difference between the maximum and minimum diameters of the filter rod. 3.2
Hardness
The mechanical resistance to compression of the filter rod body side, expressed as the percentage of the diameter of the filter rod after depression to the diameter of the filter rod before depression. 3.3
Pressuredrop
The static pressure difference between the outlet and inlet ends of the filter rod sealed by a constant airflow through a cylindrical surface. 3.4
Recessed ends
The tow of the filter rod end face is lower than the wrapping paper. 3.5wwW.bzxz.Net
Open seam
The crack of the filter rod overlap.
GB/T 5605--2002
uncleanness
The unclean traces on the filter rod surface.
Worm hole
The hole formed by the melting of the tow due to excessive application of plasticizer. 3.8
peculiar spell
The smell other than the inherent smell of acetate tow mixed in the filter rod. 3.9
inner glue-line
The glue line applied between the tow rod and the forming paper. 3.10
laboratory sample
Laboratory sample
The sample prepared for sending to the laboratory for inspection or test. 3.11
test sample
The sample prepared from the laboratory sample and the test material obtained from it. 3.12
Test portion
A certain amount of sample taken for inspection or observation. 4 Requirements
The filter rod should be non-toxic and meet the requirements of my country's food hygiene standards. 4.2 The various technical indicators of the filter rod should meet the requirements of Table 1. Table 1 Technical indicator requirements of filter rods
4.3 Appearance
The filter rod should be free of odor and mildew.
Indicator requirements
According to design requirements
According to design requirements
According to design requirements (with 10Pa as the minimum unit)According to design requirements
4.3.2 The cut of the end face of the filter rod should be flat, without stubble or glue holes, and without shrinkage with an area greater than one-third of the cross section and a depth greater than 0.5mm.
4.3.3 The surface of the filter rod should be clean. There should be no dirty spots (oil stains, yellow spots, stains) longer than 2mm, or no more than three spots even if the length is not more than 2mm.
4.3.4 The surface of the filter rod should be smooth and should not be damaged or wrinkled. 4.3.5 The overlap of the filter rod should be firmly and neatly attached, without warping, and should not have an axial bend with an arch height greater than 1mm. 178
4.3.6 Burst: After the filter rod is twisted by 90°, the length of the overlap burst should not be greater than one-sixth of the branch length. 4.3.7 Internal bonding line: There should be an internal bonding line between the tow rod and the forming paper of the filter rod. 4.4 Filter rods with special requirements shall be in accordance with the contract between the supply and demand parties. 5 Test method
GB/T 5605—2002
Prepare the sample from the laboratory sample. Except for moisture, the sample should be conditioned and tested under the conditions specified in GB/T16447 before testing.
5.1 Length
Randomly select 30 pieces from the sample as test pieces, and test them one by one according to the provisions of YC/T37.1. 5.2 Circumference
Randomly select 30 pieces from the sample as test pieces, and test them one by one according to the provisions of YC/T37.2. 5.3 Pressure drop
Randomly select 30 pieces from the sample as test pieces, and test them one by one according to the provisions of YC/T37.3. 5.4 Hardness
Randomly select 30 pieces from the sample as test pieces, and test them one by one according to the provisions of YC/T37.4. 5.5 Moisture
Randomly select 20 pieces from the sample as test pieces, and test them one by one according to the provisions of YC/T37.5. 5.6 Roundness
Randomly select 30 pieces from the sample as test pieces, and test them one by one according to the provisions of YC/T37.6. 5.7 Appearance
5.7.1 Randomly select 100 filter rods from the sample as test materials, and test them one by one according to the provisions of YC/T37.7. 5.7.2 Explosion: Randomly select five filter rods from the sample as test materials, and test them one by one according to the provisions of 5.8 of YC/T37.7. 5.7.3 Internal bonding line: Randomly select five filter rods from the sample as test materials, and use a blade to cut them open one by one along the overlap, and visually check whether there is an internal bonding line between the tow rod and the forming paper.
5.8 During the sampling process, check whether the filter rod has odor or mildew. 6 Inspection rules
6.1 Delivery inspection
The same name, same specification, and same type of filter rods delivered at one time are considered as a batch. When the number of a batch is less than 200 boxes, five boxes are selected from different parts; when the number of boxes is between 200 and 500, 10 boxes are selected from different parts; when the number of boxes is more than 500, 15 boxes are selected from different parts. Then one box is selected from each box. When a batch is less than five boxes, 1 to 2 boxes are randomly selected from each box, for a total of five boxes. According to the number of boxes taken, about 125, 60, 40, and 125 filter rods are randomly selected from each box as laboratory samples, and the total number of samples taken is not less than 600. 6.2 Type inspection
The same name, same specification, and same type of filter rods are considered as a batch. Five boxes are selected from different parts of each batch of products, and one box is randomly selected from each box, for a total of five boxes. Then about 125 filter rods are randomly selected from each box as laboratory samples, and the total number of samples taken is not less than 600. 6.3 Item Judgment Rules
6.3.1 The test results of circumference, pressure drop, hardness, length, roundness and moisture content shall be rounded off according to the significant figures in the technical requirements in 4.2. The rounding method shall be in accordance with GB/T8170.
6.3.2 Single Item Judgment
6.3.2.1 Length
If the number of filter rods that do not meet the technical requirements in the test results is greater than three, the length of the batch of filter rods shall be unqualified. 6.3.2.2 Circumference
If the number of filter rods that do not meet the technical requirements in the test results is greater than three, the circumference of the batch of filter rods shall be unqualified. 479
GB/T 5605--2002
6.3.2.3 Pressure Drop
If the number of filter rods that do not meet the technical requirements in the test results is greater than three, the pressure drop of the batch of filter rods shall be unqualified. 6.3.2.4 Hardness
If the number of filter rods that do not meet the technical requirements in the test results is greater than three, the hardness of the batch of filter rods is unqualified. 6.3.2.5 Roundness
If the number of filter rods that do not meet the technical requirements in the test results is greater than three, the roundness of the batch of filter rods is unqualified. 6.3.2.6 Moisture
If the test results do not meet the technical requirements, the moisture content of the batch of filter rods is unqualified. 6.3.2.7 Appearance
If one of the following situations occurs, the appearance of the batch of filter rods is judged to be unqualified: the cumulative number of filter rods that do not meet the technical requirements is greater than 10, and there are cracks;
Two or more filter rods have no internal bonding lines. 6.3.3 Batch judgment rules
If any of the following situations occurs, the batch of filter rods will be judged as unqualified products:--Circumference unqualified;
Pressure drop unqualified;
-Hardness unqualified;
Filter rods have peculiar smell or change;
The number of broken holes is more than two;
The number of shrinking heads is more than 10;
The moisture content of filter rods is ≥10.0%
The number of unqualified appearance is more than 30;
Two or more of the length, roundness, moisture and appearance are unqualified. 6.4 Re-inspection rules
When making single-item judgments in the delivery inspection, if one or more of the five items of length, circumference, pressure drop, hardness and roundness are unqualified, double sampling should be carried out from the batch of products to re-inspect the unqualified items. If the first re-test result does not meet the requirements of 6.3.2, the re-test items of the batch of filter rods are unqualified. If the first re-test result meets the requirements of 6.3.2, a second re-test is required. If the second re-test result meets the requirements of 6.3.2, the re-test items of the batch of filter rods are qualified; otherwise, the re-test items of the batch of filter rods are unqualified. The batch quality determination of the delivery inspection shall be based on the re-test results. 7 Marking, packaging, transportation, purchase and storage
7.1 Packaging
7.1.1 The box packaging should be complete and the seal should be firmly pasted. 7.1.2 Each box should be accompanied by a product certificate. The product should be packaged with materials of a certain strength, and the outer layer of the small basin in the box should be packaged with non-toxic plastic film.
7.1.3 The filter rods in the box should be arranged neatly and should meet the nominal quantity, with a tolerance of ±1%. 7.2 Marking
7.2.1 The packaging box should be marked with product name, trademark, specifications (circumference mm × length mm), production date, production license number, manufacturer name, address, box volume, gross weight and safety signs. 7.2.2 The graphics and text on the packaging body should comply with the provisions of the Trademark Law, and the Chinese characters should comply with the text requirements of the national standard; the numbers used should be Arabic numerals.
7.3 Transportation
GB/T 5605—2002
7.3.1 The transportation vehicle should be clean, tidy and free of odor. It should be protected from rain, moisture and extrusion during transportation, and should not be transported or mixed with damp or odorous items.
7.3.2 The filter rod packaging box should be handled with care during loading and unloading, and should not be damaged. Protective measures should be taken when loading and bundling boxes. 7.4 Storage
7.4.1 When storing filter rods, they should be placed in a well-ventilated place with appropriate environmental conditions to ensure the quality of the filter rods. The number of stacking layers should not exceed five to prevent excessive moisture and pressure.
2 They should not be stored together with odorous items, flammable items and chemicals. 7.4. 2
3 The storage period should generally not exceed six months.3 The filter rods in the box should be arranged neatly and should meet the nominal quantity, with a tolerance of ±1%. 7.2 Marking
7.2.1 The packaging box should indicate the product name, trademark, specifications (circumference mm × length mm), production date, production license number, manufacturer name, address, box volume, gross weight and safety mark, etc. 7.2.2 The graphics and text on the packaging body should comply with the provisions of the Trademark Law, among which Chinese characters should comply with the text requirements of national standards; the numbers used should be Arabic numerals.
7.3 Transportation
GB/T 5605—2002
7.3.1 The means of transportation should be clean, tidy and free of odor. During transportation, it should be protected from rain, moisture and extrusion, and should not be transported or mixed with damp or odorous items.
7.3.2 The filter rod packaging box should be handled with care during loading and unloading, and the filter rod packaging box should not be damaged. Protective measures should be taken when loading and bundling boxes. 7.4 Storage
7.4.1 When storing filter rods, they should be placed in a well-ventilated place with appropriate environmental conditions to ensure the quality of the filter rods. The number of stacking layers should not exceed five to prevent excessive moisture and pressure.
2 They should not be stored together with odorous items, flammable items and chemicals. 7.4. 2
3 The storage period should generally not exceed six months.3 The filter rods in the box should be arranged neatly and should meet the nominal quantity, with a tolerance of ±1%. 7.2 Marking
7.2.1 The packaging box should indicate the product name, trademark, specifications (circumference mm × length mm), production date, production license number, manufacturer name, address, box volume, gross weight and safety signs, etc. 7.2.2 The graphics and text on the packaging body should comply with the provisions of the Trademark Law, among which Chinese characters should comply with the text requirements of national standards; the numbers used should be Arabic numerals.
7.3 Transportation
GB/T 5605—2002
7.3.1 The means of transportation should be clean, tidy and free of odor. It should be protected from rain, moisture and extrusion during transportation, and should not be transported or mixed with damp or odorous items.
7.3.2 The filter rod packaging box should be handled with care during loading and unloading, and the filter rod packaging box should not be damaged. Protective measures should be taken when loading and bundling boxes. 7.4 Storage
7.4.1 When storing filter rods, they should be placed in a well-ventilated place with appropriate environmental conditions to ensure the quality of the filter rods. The number of stacking layers should not exceed five to prevent excessive moisture and pressure.
2 They should not be stored together with odorous items, flammable items and chemicals. 7.4. 2
3 The storage period should generally not exceed six months.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.