This standard specifies the requirements, sampling, identification and identification rules for the use and identification of yellow phosphorus packages immersed in water, less than 400kg, and sealed with airtight seals. This standard applies to the use and identification of yellow phosphorus packages. GB 19358-2003 Yellow phosphorus packaging safety specification use and identification GB19358-2003 standard download decompression password: www.bzxz.net
This standard specifies the requirements, sampling, identification and identification rules for the use and identification of yellow phosphorus packages immersed in water, less than 400kg, and sealed with airtight seals. This standard applies to the use and identification of yellow phosphorus packages.

Chapter 3, Chapter 5 and Chapter 6 of this standard are mandatory, and the rest are recommended: GB19358-2003
This standard is not equivalent to the United Nations Protocol on the Inspection and Quarantine of the Transport of Dangerous Goods (No. 12), and its technical content related to packaging is completely consistent with the above-mentioned regulations and rules. The standard text format is modified according to CB/T1.1-2000.
This standard is issued by the National Dangerous Chemical Standardization Technical Committee (5AC/1C251). The unit for the revision of this standard is Yunnan Exit-Entry Inspection and Quarantine Bureau. The participants of this standard are: Jiangxi Lushan Immigration Inspection and Quarantine Bureau, Anhui Immigration Inspection and Quarantine Bureau, Shandong Immigration Inspection and Quarantine Bureau, Beijing Immigration Inspection and Quarantine Bureau. Jiangxi Immigration Inspection and Quarantine Bureau: The participants are: Duan Yudong, Zun Haihai, Zhu Ping, Han Lijun, Xu Dong, Zhang Shaokao, Huakou, Li Tingwei. This standard is formulated for the second time.
1 Scope
Safety specification for yellow disc packaging
CB1935B—2003
This standard specifies the requirements, requirements, specifications and conditions for the use of yellow disc packaging with a volume of less than 100 and airtight seal.
This standard is included in the collection and specification of yellow disc packaging. 2 Normative references
The following documents are cited in this standard and are the terms of this standard. It is a valid document with a valid date. After that, all the changes will be made. However, all parties involved in the standard are encouraged to study whether the latest version of this document can be used. For any non-date document, the latest version shall be used. This standard: CB/T2828-1JK7 Batch Inspection and Sample Recording Procedure and Sample Table (for inspection of consecutive batches) United Nations + Dangerous Goods Transport Construction Book 3 <12th revised edition 3 Requirements
3.1 The labels and tags printed or pasted on the yellow explosive packaging should be accurate, firmly fixed, and in accordance with the requirements of the United Nations Dangerous Goods Transport Inspection and Transfer Stamp Template.
3.2 The surface of the yellow explosive packaging should be clean and no residue, river frame, penetration or paint flow is allowed. 3.3 The yellow phosphorus packaging selected by the enterprise must be consistent with the properties of the yellow phosphorus before consumption. In addition, the yellow phosphorus packaging requirements specified in the "National Dangerous Goods Transport Recommendation Specifications" shall be checked and verified. The inspection results shall be consistent with the actual load.
3. The yellow phosphorus parts after sliding shall not be replaced. When the phosphorus in the barrel is completely empty, the yellow phosphorus shall be protected by water to prevent it from contacting with air during transportation. The minimum distance between the inner surface of the filter element and the inner wall of the filter element should not be less than 3 m. The space between the top and bottom of the filter element should not be greater than 5% of the total volume of the filter element. 3.5 The closure of the filter element should be tightly combined with an appropriate sealing ring. The degree of tightening should be such that the sealing area is not damaged and the water in the barrel does not flow into the two parts. 3.6 The maximum mass of a single piece of the filter element should be less than the maximum allowable mass of the container performance test (the effective mass calculation method is the negative of the volume of the filter element multiplied by the maximum relative density of the whole package). 4 Sampling | |tt||2.1 Inspection batch
The inspection batch is made of the same raw materials, the same production process and the same packaging materials, and the quantity is 3200 pieces. 2.2 Group current rulesWww.bzxZ.net
According to the provisions of B/2A-7, the monthly normal inspection shall be carried out, and the sampling shall be conducted on half of the selected pool. 4.3 Sampling number
The sampling number is shown in 1.
CB13358-2003
5 Identification
Northern grass standard
51--55
91-150
131--23c
:511200
1 20]3 2X
Table 1 Draw and inspect the entire quantity
5.1 Check whether the selected precious phosphorus packaging is suitable for the quality of the product, whether the whole packaging has passed the Class I rapid performance test, and whether its application form, factory inspection result form and performance inspection result form are specified: the number should be consistent with the actual product. 5.3 Check whether the yellow phosphorus packaging has a closure and whether the drawing is complete. Use a ruler to check the interior of the packaging at the door, and whether the cover and reserved space meet the requirements of 3.4. 5.4 The sample packaging parts are completely covered with water in the closure. Check whether the closure is leaking. 5.5 Use a platform scale with a base of 0Ck to calibrate the gross weight of the yellow card packaging parts before weighing. Check whether the gross weight of the liquid is lower than the maximum gross weight of the packaging parts. 6.1 The yellow phosphorus production enterprise shall ensure that the used packaging is in accordance with the provisions of this standard, and issue relevant inspection and identification: the user shall confirm the provisions of this standard, and the acceptance inspection of the yellow phosphorus packaging shall be initiated. 6.2 Identification items shall be inspected on the key items in Chapter 3 and Chapter 5 of this standard. 6.3 The number of parts to be inspected shall be determined according to the order quantity, but the number of parts to be inspected shall not exceed the maximum batch size specified in 4.1. 6.4 The validity period of the inspection report shall be calculated from the date of the assembly, and the validity period shall not exceed one year, but this validity period shall not exceed the validity period of the performance inspection report.
6.5 If there is any unqualified packaging, it will be judged as unqualified. If there is any unqualified packaging, it will be judged as unqualified. After the above items are determined, an inspection report will be issued. 6. If the unqualified batch is handled, the unqualified special packaging parts in the unqualified batch will be returned for processing or removed, and then re-inspected with a slightly lower degree of strictness. 2
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.