title>GB/T 2554.1-1998 Mechanical dividing head accuracy test - GB/T 2554.1-1998 - Chinese standardNet - bzxz.net
Home > GB > GB/T 2554.1-1998 Mechanical dividing head accuracy test
GB/T 2554.1-1998 Mechanical dividing head accuracy test

Basic Information

Standard ID: GB/T 2554.1-1998

Standard Name: Mechanical dividing head accuracy test

Chinese Name: 机械分度头 精度检验

Standard category:National Standard (GB)

state:Abolished

Date of Release1998-01-01

Date of Implementation:1999-09-01

Date of Expiration:2009-01-01

standard classification number

Standard ICS number:Mechanical Manufacturing>>Machine Tool Devices>>25.060.20 Indexing and Tool/Workpiece Holding Devices

Standard Classification Number:>>>> >>>>52

associated standards

alternative situation:Replaced GB 2554-1984; replaced by GB/T 2554-2008

Procurement status:eqv ISO 5734—1986

Publication information

publishing house:China Standards Press

Publication date:1999-09-01

other information

Release date:1981-03-30

Review date:2004-10-14

Drafting unit:Yantai Machine Tool Accessories Research Institute

Focal point unit:National Technical Committee for Metal Cutting Machine Tools Standardization

Publishing department:State Administration of Quality and Technical Supervision

competent authority:China Machinery Industry Federation

Introduction to standards:

This standard specifies the geometric accuracy test items, tolerances and test methods for general-purpose mechanical dividing heads for machine tools. This standard applies to the accuracy test of dividing heads. It does not apply to the operation test of dividing heads, which is generally carried out before the accuracy test. GB/T 2554.1-1998 Accuracy test of mechanical dividing heads GB/T2554.1-1998 Standard download decompression password: www.bzxz.net

Some standard content:

125060.20
National Standard of the People's Republic of China
GB/T2554.1--2554.2—1998
Mechanical dividing head
Mechanical dividing
Published on November 18, 1998
Implemented on September 1, 1999
National Quality and Technical Supervision Bureau
GB/T2554,11998
This standard equivalently adopts the international standard IS05734-1S86 machine tool dividing head inspection case change inspection, and abolishes the basic international standard 2554-4 in terms of technical content, resulting in some continuous changes, and omitting the provisions of GB/T1.11993, etc. The design rules of this standard can be simplified by adopting the national standard S5734-186. The British standard is not included in the data. Compared with the previous version, the addition of "the same rail joint auxiliary inspection head" and "the standard rail line to the reference type Bo side of the inspection must be implemented. This standard replaces GB2554-84 from the date of implementation. This standard is proposed by the Ministry of Machinery Industry of Shandong Province.
This standard is under the jurisdiction of the State Machine Tool Accessories Research Institute. The responsible drafting of this standard is: Taiwan Machine Tool Accessories Research Institute: The drafting of this standard is: Yanji Machine Tool Accessories Factory, Wuhan Machine Tool Accessories Factory. This standard was issued for the first time in 1573, and will be revised for the second time in 1981, and will be revised for the second time in 1381. c8/T2554.1—1998www.bzxz.net
ISO Foreword
ISO is a worldwide standard organization. The preparation of international standards is usually carried out by ISO technical committees, which represent the interests of all standard-setting bodies concerned with the standard being prepared. 15 relevant international organizations, governmental and non-governmental organizations, help plan this work.
The draft standard shall be published after the decision of the main S) Council. According to the 1 effective) execution procedure, 75% of the testers must pass the test before the standard is released. The international standard IS)5724 was developed by the ISO/TCS5\Machine Tool Technical Committee". This is the second edition, which replaced the first edition (1S)5734-1978). Geometric inspection G1, (F5 and G6 items have been revised. Users need to be aware that all international standards will be revised and the referenced standards, unless otherwise specified, refer to the latest versions. Scope
National Standard of the People's Republic of China
Mechanical dividing head
Degree inspection
Mechanical dividing hcads-
Testiny of meeraey
CB/T 2554.1--1993
q1so57341986
Agency 255-84
This standard is generally used to define the inspection items and supplementary inspection methods of the dividing head for machine tools (hereinafter referred to as the dividing head):
This standard is used for the initial inspection of the dividing head: It is not suitable for the operation inspection of the dividing head. The operation inspection of the dividing head is generally carried out before the accuracy inspection:
2 Reference standard
Next The provisions contained in the following standards are cited in this standard and constitute the text of this standard. The versions shown are valid at the time of publication of the standard: All standards will be referenced. The parties who use this standard should consider the latest version of the following standards: J/T2570-182 Precision inspection rules for metalworking machine tools 3 General requirements
3.1 The precision inspection method of this standard should be in accordance with the relevant provisions of 113/1267C. 3.2 The precision inspection items listed in this standard are listed in the order of , it is not necessary to conduct the actual inspection. During the inspection, the inspection can be carried out according to the convenience of assembly and disassembly of the mold and the inspection can be carried out in any order. 3.3 The parts specified in this standard can be selected for inspection according to the agreement. 3.4 If the actual measured length is different from the measured length specified in this standard, the difference can be converted according to the provisions of 2.3.1.1 of JB/T2570:1932. If the conversion result is less than c.510mm, it shall be calculated as 0.c13mm. 4 Geometric accuracy inspection (See table:)
of the spindle with hole)
radial movement
each near the main temporary 6)
> main shaft case
3mm
State Administration of Quality and Technical Supervision 1998-11-18 batch of difficult-to-calibrate tools
$62670
1983 market related women
indicator, 3.6.1.2.3
1999-09-01 implementation
GB/T 2554. 11998
Table 1 (thread)
Blood dust dimension 5.13
According to the linkage
Main protection heart n
Temporary effective diameter courtyard 0.0 2 0
bMain axis period: uuu
e) Earth transmission axis room 10020
Supporting jump pool!
(Price adjustment period direction:
The verticality of the main shaft rotation to the
bottom surface
1300 is
point
check the product
as the indicator
structure test method
according to 15/1267V
1B2's relevant policy 3
5. 6. 2. 2
summary requirements, period n) 5. e. 1. 2. 2
each force is installed 65.5. 2. 2
) 5. 6- 3. 2
position system is full! Regulations
Indicator, special
stand|
5. 5. 1. 2. 1
Special stand with indicator is fixed on the ten-axis, the indicator head is vertical and the inspection level
state is integrated, so that the indicator potential
, the two points are consistent with zero,
measure the most basic health
regulations to maintain the main and auxiliary integration,
recognize the major design of the indicator to read
GB/T 2554.1—1998
Table 1 (width)
Inspection items
Inspection tools
Inspection and supervision party
Model B/T267℃
-1982 related to the contract
Dividing head set key room position measurement
) Main and auxiliary axis
Indicator, age
For the main key positioning
The surface is left in the base as a T-type indicator Measure the light transmission degree of the measuring surface of the long table stand: the degree is (b) the sticky axis and (U) the parallel of the distance plane. (r) The main axis is 0.015° to the side of the standard T plastic, and the insert is removed. Adjust the main control to the horizontal position. (n) 5. 4- 1. 2. 11. 5. 4.1. 2.4. Quick test. The main beat range is 1. On the two opposite sides of the initial test, the test is carried out. The error is calculated by taking the average of the two teachings. It is necessary to adjust the positioning monitoring system at the same time. e) 5-4-4. 2. On the special table stand, do not measure the white head every time. When the special table is positioned near the main shaft end, change the new table. When the special table is positioned, write down the reading and turn the table 130 degrees to make it close to the certain measurement surface for re-inspection. The error is calculated as the rate of difference between the two readings required and w*±45%. Method! n> 6. 1. 1. 1
Graduation
Degree
Measurement
Measurement
Auxiliary number transfer main male belt
: Auxiliary early good degree
These,
b) The main axis is on the child b) +1'
1/4 West or large
Source
Main belt
Degree 2
Head agent
Electric original connection line 0.020
For the reference model
Locate the side of the plane (1. 12n
rate;
b) the dividing head and
seat song injection line
parallel
indicator, when
,
1 6. 1. 1.4
Including transmission error and sub-disk
Taipei damage equipment
5.4.i. 2. 4
Division of the world and the order of positioning
Free, 30
: UL long, long sugar male solid reference T-type sugar over-movement position hit on the inspection in the two
learning not to protect oxygen pre-tip
special table stand
in the fast inspection card called forbidden inspection
h) to allow the adjustment of the fee scale
seat height.
),h】Error signs are all indicated
Reading teaching plan
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.