SY/T 0075-2002 Specification for design of fire dikes in oil tank areas
Some standard content:
Petroleum and Natural Gas Industry Standard of the People's Republic of China Design specification for fire-dike in tank area SY/0075--2002 Edited by: China Petroleum and Natural Gas Pipeline Engineering Co., Ltd. Approved by: State Economic and Trade Commission Petroleum Industry Press 2002 Beijing 2 Terms and symbols 2.1 Terms
2.2 Symbols
3 Arrangement of firebreaks
3.1 General provisions
3.2 Arrangement
4 Selection and construction of firebreaks
4.2 Construction
5 Strength and stability verification of firebreaks
Load combinations and internal force calculations
5.2 Strength verification
5.3 Stability verification
Appendix A Table of earth pressure coefficients
Appendix B Firebreak foundation Friction coefficient of bottom
Explanation of words and terms used in the standard
Appendix Explanation of clauses of the oil tank area fire dike design specification 2
Announcement of the State Economic and Trade Commission of the People's Republic of China
No. 32 of 2002
Announcement of 78 petroleum industry standards
The State Economic and Trade Commission approved 78 petroleum industry standards, which are now announced and will be implemented from August 1, 2002.
The above standards are published and distributed by Youyou Industry Press. Appendix: Names and numbers of 78 oil industry standards State Economic and Trade Commission of the People's Republic of China May 28, 2002
Appendix:
Names and numbers of 78 oil industry standards
Standard name
Standard number
Alternative standard number
Economic calculation of anti-corrosion engineering$Y^10042—2002SYI42—89 method
Oil and gas field engineering survey specificationSYI0054-2002SY/I0054-—93 Fire dike design for oil tank area-SpecificationSY/T0075—2002SY0075—93 Standard
Epoxy glass lining of steel storage tankSY/T0326—2 002 Glass fiber reinforced plastic technical standard
Polyethylene for buried steel pipelineSY/T0413--2002SY/T4013--95 Anticorrosion layer technical standard
Metallic pipeline for petroleum and natural gasSY/T0452-2002SY4052-92 Welding process assessment
Steel butt-welded pipe for oil and gas pipelineSY/F0518-2002SY/T (518--92 design code
Seismic detector part 3SY/『5046.3--200)2 Eddy current geophone
Seismic detector part 4SY/5046.4-2002 Moving coil acceleration detector
Cutter for drilling and repairing wells
SY 5070-2002 SY 5070-91
SY 5424-91
SY/T 5688—95
Standard name
Standard number
Replacement standard number
Items for evaluating and calculating the quality of the productSY/T5088—2002SY/T5088—93
Sulfonated lignite for drilling fluidSY/T5092--2002SY/T5092-93SMC
13 Specification for wellhead equipment and Christmas treesSY/T5127—2002SY5127—-92 Specification
SY 5279.1--91
SY 5279.291
SY 5279.3—91
SY 515693
14Centrifugal turbine for oil drilling rigSY/T5141—2002SY/T5141—93Hydraulic torque converter
Metallic element atoms in rocksSY/T5161—2002SY5161—87Absorption spectrum determination method
Drill string conversion jointWww.bzxZ.net
SY/T 5200-2002 SY 5200-93
Natural gamma spectrum of rock samplesSY/T5252--2002SY/T5252—91Analysis method
Eccentric water distribution tool
Oil transfer arm for port loading and unloading
SY/T 5253—91
SY/T 5275---2002 SY 5275—91SY/T 5298--2002 SY/T 5298—91Onshore seismic exploration data collectionSY/T5314-—2002SY/T5314—9520
Collection quality inspection and acceptance
Percussion wellbore coring technologySY/F5326—2002SY/T5326—93Procedure
Sesbania gum for fracturing
SY/T 5605—93
SY/T 5341—2002 SY/T 5341--88Serial number
Standard name
Standard number
Replacement standard number
Reservoir sensitivity flow testSY/T5358-2002SY/T5358-94Evaluation method
Expandable packer
Special coring tool
Oil workover winch
Twist-out winch for oil drilling rig
SY/T 5404-2002 SY/T 5404-91SY/T 5414-2002 SY 5414-91
SY/T 6200--1996
SY7I 5470- 2002 SY 5470-92
SY/T 55322002 SY/r 553292
DS series for right oil drilling rigSY/T 5533--2002 SY/T 5533-92Electromagnetic eddy current brake
Specification for commissioning of crude oil pipelineSY/F5536-2002SY/T5536-92Specification
Physical property analysis method of fluid in condensate gas reservoirSY/T5543--2002SY/T5543--92
Single screw oil pump
SY/T 5549--2002 SY 5549--92
Technical specification for open hole and cased well testing$YT5600-2002$Y/I5600--93Operation
SY/I 5606--93
Cable conveyed perforating technologySY/T5604—2002SY/T5604—9333
Technical procedures and quality assessment
Performance inspection technical procedures for oil testing toolsSY/T 5710—2002SY/T 5712-95
SY/T 5710-95
35Petroleum geological rock names and color codesSY/T5751—2002SY/T5751—1995Standard name
Pour point depressant for pipeline crude oil
Standard number
Alternative standard number
SY/T 5767--2002SY/T 5767--1995SY/T 588793
37Technical specification for exploration of controlled source acoustic magnetotelluricSY/T5772-2002SY/T5772-1995
3811I-area seismic exploration measurement technical specificationSY/T5775-2002SY/T5775-1995
39Injection and output profile loggingSY/T5783-2002SY/T5783-93Data interpretation specification
Casing shaping and sealing reinforcementSY/T5790--2002SY/T5790-93Technical practice
Technical specification for ground vehicle explorationSY/T5819--2002.SY/T5819-93 Engineering
Sucker rod centralizer
SY/T 5832--2002 SY/I 5832-93 Chemical agent plugging removal process for oil and water wellsSY5849--2002SY/I5849-93 Economic effect evaluation method
Labor quota for gas production engineering
Labor quota for gas transmission engineering
SY/T 5896--2002SY/R 5896--93SY/T 5897--2002SY/I 5897-9346
Polyacrylamide for drilling fluidSY/T5946--2002SY/T5946-94 Potassium salt
Petroleum gravity, magnetic and electricSY/T 6055-2002 SY/T 6055-94 method, geochemical exploration map
standard name
standard number
replacement standard number
method for determining the thermal physical properties of formation rocksSY/6107-2002SY/T6107-1994
geochemical exploration map
standard name
standard number
replacement standard number
method for determining the thermal physical properties of formation rocksSY/6107-2002SY/T6107-1994
geochemical exploration mapSY/T6110-2002SY/T6110--94 description of geological characteristics of carbonate gas reservoir developmentSY/T6110-2002SY/T6110--94
natural gas pipeline commissioningSY/T 6233-2002SY/T6233-1996 Specification
Oil well pipe full size test methodSY/T6238.2-200251
Method of oil and casing thread
Shackle test
Petroleum industry workplace labor protection equipment equipment requirementsSY/T6524-2002Foam drainage gas production recommendedSY/T6525-2002Method
54 Hydrochloric acid and Dynamic SY/T6526-2002 Reaction rate determination method for carbonate rock
Original SY/T6527-200255 of electrical and acoustic imaging logging
Data quality specification
Method for measuring dielectric constant of rock sampleSY/T6528-2002
Operation specification of fixed fire protection system for crude oil depotSY6529-2002System
Non-corrosive: for gas transportationSY/T6530-20 02 Pipeline inner coating
Straight seam resistor for oil well pump bodySY/I6531--200259
Welded steel pipe
Standard name
Standard number
Calibration method of induced polarization instrumentSY/T6532-2002Stability well test test and interpretationSY/T6533-2002Method
Twin screw oil and gas mixed transmission pump
High pressure gas underground gas storage well
SY/T 6534-—2002
SY/T 6535—2002
Steel water tank inner wall cathodic protection SY/T6536—2002 Technical specification
Natural gas purification plant-gas and SY/T6537—200265
Solution analysis method
Formulated selective desulfurization solution SY/T6538—200266
67BOX Seismic data acquisition SY/I6539—2002 System inspection items and technology
68 Drilling and completion fluid damage to oil layer SY/I6540—2002 Indoor evaluation method
Recommended practices for planning, design and construction of fixed offshore platforms SYT10009
2002
Method Load resistance coefficient
Design method (Supplement 1)
70 Offshore oil engineering drawing specification SY/T10028-Model
Replacement standard number
SY/T 10009-
Standard name
Standard number
Recommended practices for planning, design and construction of fixed offshore platforms $Y/I10030-71
2002
Method 1—Working stress design
Method (Supplement 1)
Specification for submarine pipeline systems
SY/T 10037-
Recommended Practice for Offshore Fixed Platform Helicopter Site Planning, Design and Construction 2002
Recommended Practice for Positioning Systems for Floating Structures SY/I10040-74
Recommended Practice for Design and Analysis 2002
Electrical Equipment Installation in Oil-Filled Facilities SY/T10041-1 Class I and Class II Areas 2002
Recommended practice for domain division
Recommendations for the design and installation of offshore production platform piping systemsSYI10042-
Guidelines for pressure relief and decompression systemsSY/110043-77
78Recommended practice for sizing, selection and installation of refinery pressure relief devicesSY/I10044-2002
Replacement standard number
SY/T 10030-
SY/T 4804--92
SY/T 4806-92
SY/T 4811-92
SY/T 4809--92
SY/r 4812—92
This specification is based on the arrangement of the "Notice on Issuing the 2001 National Plan for the Formulation and Revision of Standards for the Petroleum, Natural Gas and Petrochemical Industries" issued by the former State Administration of Petroleum and Chemical Industry on April 10, 2000. Shandong Petroleum and Natural Gas Pipeline Engineering Co., Ltd. is responsible for revising the "Design Specifications for Fire Dikes in Oil Tank Areas" SY0075—93
This revision has carried out a lot of on-site adjustments, summarized the technical development and practical experience over the years, fully solicited the revision opinions of all parties, made partial modifications to the content and structure, expanded the meaning of fire dikes and separation dikes, clarified the role of fire dikes, re-defined the total volume of tank groups, increased the height of fire dikes, abolished the selection of plain concrete dikes and rough concrete dikes:
This specification will take effect from the date and replace SY0075—93 at the same time. This specification is issued by China National Petroleum Corporation and is under the jurisdiction of China National Petroleum Corporation. China National Petroleum Corporation is responsible for the interpretation of this specification. The unit of this specification is China National Natural Gas Pipeline Engineering Co., Ltd. The main drafters of this specification are Chen Huibi, Feng Baokun, Liu Changqing, Guo Baoshen, Xu Qi
The previous versions of the standards replaced by this specification are: -SY 0075--93.
1.0.1. This specification is formulated to unify the design requirements of fire dikes in the oil tank areas of factories, stations and depots of the oil and gas industry, improve the design quality, and ensure the safety of the oil tank areas. 1.0.2 This specification is applicable to the design of fire dikes in the new construction and expansion projects of the above-ground oil tank areas in the oil and gas industry; it is not applicable to the design of protective walls (dikes) in liquefied petroleum gas and natural gas condensate tank areas. The fire dike renovation project of the oil tank area can be designed in accordance with this specification: 1.0.3 The design of the fire dike in the oil tank area, in addition to complying with this specification, shall also comply with the provisions of the relevant mandatory standards currently in force in the country.2-200251
Method for testing the thread of oil and casing
Break test
Requirements for the equipment of labor protection equipment in the workplace of petroleum industrySY/T6524-2002
Recommended foam drainage and gas productionSY/T6525-2002Method for determining the reaction rate of hydrochloric acid and carbonate rockSY/T6526-2002Original data quality specification of electrical and acoustic imaging loggingSY/T6527-200255
Method for measuring the dielectric constant of rock samplesSY/T6528-2002Method
|Operation specification of fixed fire protection system for crude oil depotSY6529-2002
Non-corrosive: SY/T6530-2002 Pipeline inner coating for gas transportation
Straight seam resistor for oil well pump bodySY/I6531--200259
Welded steel pipe
Standard name
Standard number
Calibration method of induced polarization instrumentSY/T6532-2002Stability well test test and interpretationSY/T6533-2002Method
Twin-screw oil and gas mixed transmission pump
High-pressure gas underground gas storage well
SY/T 6534--2002
SY/T 6535—2002
Steel water tank inner wall cathodic protection SY/T6536—2002 Technical specification
Natural gas purification plant-gas and SY/T6537—200265
Solution analysis method
Formulated selective desulfurization solution SY/T6538—200266
67BOX Seismic data acquisition SY/I6539—2002 System inspection items and technology
68 Drilling and completion fluid damage to oil layer SY/I6540—2002 Indoor evaluation method
Recommended practices for planning, design and construction of fixed offshore platforms SYT10009
2002
Method Load resistance coefficient
Design method (Supplement 1)
70 Offshore oil engineering drawing specification SY/T10028-Model
Replacement standard number
SY/T 10009-
Standard name
Standard number
Recommended practices for planning, design and construction of fixed offshore platforms $Y/I10030-71
2002
Method 1—Working stress design
Method (Supplement 1)
Specification for submarine pipeline systems
SY/T 10037-
Recommended Practice for Offshore Fixed Platform Helicopter Site Planning, Design and Construction 2002
Recommended Practice for Positioning Systems for Floating Structures SY/I10040-74
Recommended Practice for Design and Analysis 2002
Electrical Equipment Installation in Oil-Filled Facilities SY/T10041-1 Class I and Class II Areas 2002
Recommended practice for domain division
Recommendations for the design and installation of offshore production platform piping systemsSYI10042-
Guidelines for pressure relief and decompression systemsSY/110043-77
78Recommended practice for sizing, selection and installation of refinery pressure relief devicesSY/I10044-2002
Replacement standard number
SY/T 10030-
SY/T 4804--92
SY/T 4806-92
SY/T 4811-92
SY/T 4809--92
SY/r 4812—92
This specification is based on the arrangement of the "Notice on Issuing the 2001 National Plan for the Formulation and Revision of Standards for the Petroleum, Natural Gas and Petrochemical Industries" issued by the former State Administration of Petroleum and Chemical Industry on April 10, 2000. Shandong Petroleum and Natural Gas Pipeline Engineering Co., Ltd. is responsible for revising the "Design Specifications for Fire Dikes in Oil Tank Areas" SY0075—93
This revision has carried out a lot of on-site adjustments, summarized the technical development and practical experience over the years, fully solicited the revision opinions of all parties, made partial modifications to the content and structure, expanded the meaning of fire dikes and separation dikes, clarified the role of fire dikes, re-defined the total volume of tank groups, increased the height of fire dikes, abolished the selection of plain concrete dikes and rough concrete dikes:
This specification will take effect from the date and replace SY0075—93 at the same time. This specification is issued by China National Petroleum Corporation and is under the jurisdiction of China National Petroleum Corporation. China National Petroleum Corporation is responsible for the interpretation of this specification. The unit of this specification is China National Natural Gas Pipeline Engineering Co., Ltd. The main drafters of this specification are Chen Huibi, Feng Baokun, Liu Changqing, Guo Baoshen, Xu Qi
The previous versions of the standards replaced by this specification are: -SY 0075--93.
1.0.1. This specification is formulated to unify the design requirements of fire dikes in the oil tank areas of factories, stations and depots of the oil and gas industry, improve the design quality, and ensure the safety of the oil tank areas. 1.0.2 This specification is applicable to the design of fire dikes in the new construction and expansion projects of the above-ground oil tank areas in the oil and gas industry; it is not applicable to the design of protective walls (dikes) in liquefied petroleum gas and natural gas condensate tank areas. The fire dike renovation project of the oil tank area can be designed in accordance with this specification: 1.0.3 The design of the fire dike in the oil tank area, in addition to complying with this specification, shall also comply with the provisions of the relevant mandatory standards currently in force in the country.2-200251
Method for testing the thread of oil and casing
Break test
Requirements for the equipment of labor protection equipment in the workplace of petroleum industrySY/T6524-2002
Recommended foam drainage and gas productionSY/T6525-2002Method for determining the reaction rate of hydrochloric acid and carbonate rockSY/T6526-2002Original data quality specification of electrical and acoustic imaging loggingSY/T6527-200255
Method for measuring the dielectric constant of rock samplesSY/T6528-2002Method
|Operation specification of fixed fire protection system for crude oil depotSY6529-2002
Non-corrosive: SY/T6530-2002 Pipeline inner coating for gas transportation
Straight seam resistor for oil well pump bodySY/I6531--200259
Welded steel pipe
Standard name
Standard number
Calibration method of induced polarization instrumentSY/T6532-2002Stability well test test and interpretationSY/T6533-2002Method
Twin-screw oil and gas mixed transmission pump
High-pressure gas underground gas storage well
SY/T 6534--2002
SY/T 6535—2002
Steel water tank inner wall cathodic protection SY/T6536—2002 Technical specification
Natural gas purification plant-gas and SY/T6537—200265
Solution analysis method
Formulated selective desulfurization solution SY/T6538—200266
67BOX Seismic data acquisition SY/I6539—2002 System inspection items and technology
68 Drilling and completion fluid damage to oil layer SY/I6540—2002 Indoor evaluation method
Recommended practices for planning, design and construction of fixed offshore platforms SYT10009
2002
Method Load resistance coefficient
Design method (Supplement 1)
70 Offshore oil engineering drawing specification SY/T10028-Model
Replacement standard number
SY/T 10009-
Standard name
Standard number
Recommended practices for planning, design and construction of fixed offshore platforms $Y/I10030-71
2002
Method 1—Working stress design
Method (Supplement 1)
Specification for submarine pipeline systems
SY/T 10037-
Recommended Practice for Offshore Fixed Platform Helicopter Site Planning, Design and Construction 2002
Recommended Practice for Positioning Systems for Floating Structures SY/I10040-74
Recommended Practice for Design and Analysis 2002
Electrical Equipment Installation in Oil-Filled Facilities SY/T10041-1 Class I and Class II Areas 2002
Recommended practice for domain division
Recommendations for the design and installation of offshore production platform piping systemsSYI10042-
Guidelines for pressure relief and decompression systemsSY/110043-77
78Recommended practice for sizing, selection and installation of refinery pressure relief devicesSY/I10044-2002
Replacement standard number
SY/T 10030-
SY/T 4804--92
SY/T 4806-92
SY/T 4811-92
SY/T 4809--92
SY/r 4812—92
This specification is based on the arrangement of the "Notice on Issuing the 2001 National Plan for the Formulation and Revision of Standards for the Petroleum, Natural Gas and Petrochemical Industries" issued by the former State Administration of Petroleum and Chemical Industry on April 10, 2000. Shandong Petroleum and Natural Gas Pipeline Engineering Co., Ltd. is responsible for revising the "Design Specifications for Fire Dikes in Oil Tank Areas" SY0075—93
This revision has carried out a lot of on-site adjustments, summarized the technical development and practical experience over the years, fully solicited the revision opinions of all parties, made partial modifications to the content and structure, expanded the meaning of fire dikes and separation dikes, clarified the role of fire dikes, re-defined the total volume of tank groups, increased the height of fire dikes, abolished the selection of plain concrete dikes and rough concrete dikes:
This specification will take effect from the date and replace SY0075—93 at the same time. This specification is issued by China National Petroleum Corporation and is under the jurisdiction of China National Petroleum Corporation. China National Petroleum Corporation is responsible for the interpretation of this specification. The unit of this specification is China National Natural Gas Pipeline Engineering Co., Ltd. The main drafters of this specification are Chen Huibi, Feng Baokun, Liu Changqing, Guo Baoshen, Xu Qi
The previous versions of the standards replaced by this specification are: -SY 0075--93.
1.0.1. This specification is formulated to unify the design requirements of fire dikes in the oil tank areas of factories, stations and depots of the oil and gas industry, improve the design quality, and ensure the safety of the oil tank areas. 1.0.2 This specification is applicable to the design of fire dikes in the new construction and expansion projects of the above-ground oil tank areas in the oil and gas industry; it is not applicable to the design of protective walls (dikes) in liquefied petroleum gas and natural gas condensate tank areas. The fire dike renovation project of the oil tank area can be designed in accordance with this specification: 1.0.3 The design of the fire dike in the oil tank area, in addition to complying with this specification, shall also comply with the provisions of the relevant mandatory standards currently in force in the country.3. In addition to complying with this specification, the design of firebreaks in oil tank areas shall also comply with the provisions of the relevant mandatory standards currently in force in the country.3. In addition to complying with this specification, the design of firebreaks in oil tank areas shall also comply with the provisions of the relevant mandatory standards currently in force in the country.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.