This standard specifies the type, model and series parameters of the inner and outer rotors of the oil pumps for small and medium power internal combustion engines. This standard applies to the powder metallurgy inner and outer rotors of the oil pumps for small and medium power internal combustion engines. The inner and outer rotors of non-powder metallurgy can also refer to this standard. JB/T 6005-1992 Series parameters of oil pump rotors for internal combustion engines JB/T6005-1992 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T600592
Internal Combustion Engine Oil Pump Rotor Series Parameters
Published on 1992-05-28bzxz.net
Implementation of the Ministry of Machinery and Electronics Industry of the People's Republic of China on 1993-01-01
Mechanical Industry Standard of the People's Republic of China
Internal Combustion Engine Oil Pump Rotor Series Parameters
1. Subject Content and Scope of Application
JB/T6005-92
This standard specifies the type, model and series parameters of the inner and outer rotors of medium and small power internal combustion engine oil pumps. This standard applies to powder metallurgy inner and outer rotors (hereinafter referred to as inner and outer rotors) of medium and small power internal combustion engine oil pumps. Non-powder metallurgy inner and outer rotors can also refer to this standard.
2 Reference standards
JB/T5090 Technical conditions for powder metallurgy rotors of internal combustion engine oil pumps 3 Terms
3.1 Gear ratio i
The ratio of the number of teeth Z of the inner rotor to the number of teeth Z of the outer rotor, i.e. Z/Z3.2 Eccentricity e
The distance between the center of the inner rotor and the center of the outer rotor when the inner and outer rotors are in meshing condition, mm. 3.3 Clearance 8
The radial distance between the top of the inner rotor tooth and the root of the outer rotor tooth when the inner and outer rotors are in meshing condition, mm. 4 Type, model and series parameters
4.1 Type
The rotor profile is a trochoid.
4.2 Model
The series model name is composed of the Latin letters JBZ, the outer diameter of the outer rotor and the rotor width. JBZ=××-××
Rotor width, mm
Outer diameter of outer rotor, mm
Oil rotor
When the outer diameter of the same outer rotor is the same, use footnotes a and b to distinguish, such as 70a; 70-b4.3 Series parameters
Rotor series dimensions and parameters are shown in Table 1.
4.4 Materials of inner and outer rotors. Dimensional accuracy should comply with the provisions of JB/T5090. 4.5 Calculation of unit displacement See Appendix A (reference) Approved by the Ministry of Machinery and Electronics Industry on May 28, 1992 Implemented on January 1, 1993
JB/T600592
1960000
r-01x16808
1-0190
1-0180018
-010988| |tt||1012980
.00*68
0090~9
X×792
A1: Unit displacement g is calculated according to formula (A1):
JB/T6005-92
Appendix A
Calculation of unit displacement
(reference)
q=AZ,×10-. L/(rcm)
Where: A——Inner rotor tooth swept area, cm: Z, number of inner rotor teeth.
A2 Theoretical flow Q is calculated according to formula (A2):
Q=qbnL/min
-Rotor width, cm;
Where: b—
Oil pump speed, r/min.
A3 The relationship between theoretical flow (when the speed is 1000r/min) and rotor width is shown in Figure A1.00
JBZ23××
Additional instructions:
This standard is proposed and managed by the Shanghai Internal Combustion Engine Research Institute of the Ministry of Machinery and Electronics Industry. This standard is drafted by the Shanghai Internal Combustion Engine Research Institute of the Ministry of Machinery and Electronics Industry.
JBZ70b××
JBZ71××
JBZ70a××
JBZ67××
JBZ62X×
JBZ60××
JBZ54××
JBZ50××
JBZ41××
JBZ35××
JBZ29××
Rotor width mm
From the date of implementation of this standard, NJ368-85 "Powder Metallurgy Rotor Oil Pump Rotor Series Parameters" will be invalid (A1)
Huhua People's Republic||t t||Hangzhou Machinery Industry Standard
Two-fuel engine oil pump rotor series parameters
B/T/6005--92
Published by the Machinery Standardization Research Institute of the Ministry of Machinery and Electronics Industry, printed by the Machinery Standardization Research Institute of the Ministry of Machinery and Electronics Industry, Beijing 8144. PO Box 100081)
Copyright reserved, no reproduction allowed
Format 880×1230
D1/16 Printing sheet 1/2 Number of words 6,000
First edition October 1992 October 1992 Group production, that is, 0po fixed bottle
No. 0958
z6-2009/
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.