Some standard content:
ICS61.080
Distribution No.: Y99
Registration No.: 15143-2005
Light Industry Standard of the People's Republic of China
QB/T1065—2004
Replaces QB/T1065-1991
Shoemaking machinery
Lasting machine
Footwear machinesLasting machlne2004-12-14 Issued
National Development and Reform Commission of the People's Republic of China 2005-06-01 Implementation
This standard is a revision of QB/1065-[991 belt machine. The main technical differences between the standard and QB1065-[991 are as follows: QB/T10652004 Basic parameters are adjusted: Add "front-end" before the requirements for front-end machines to distinguish the back-end machines: The basic requirements for assembly quality are increased from two to eight, and there are quantitative indicators in the requirements: Requirements for electrical systems, the original standard can be improved The system "shall conform to the new definition of GB/T5226", which respectively stipulates the continuity of the protection circuit, the contraction of the power circuit and the control test requirements: in the performance of the whole machine, it has added the requirements for the "spray system". This standard was issued by the China Federation of Industry and Commerce and is returned to the National Middle School of Machinery Standardization. This standard was issued by Wenzhou Dalong Machinery Co., Ltd. Responsible for: National Research Institute of Footwear Industry. The main drafters of this standard are: Yang Yongguo, Sheng Xiaoshan, Kong Yuli. From the date of implementation of this standard, the original light industry standard QR/T10G5-1991 issued by the Ministry of Light Industry 3. 1 Scope
Shoemaking machinery upper stretching machine
QB/T 1065—2004
The standard specifies the product classification, requirements, test methods, inspection rules and marking, assembly, transportation and operation of paper uppers. This standard applies to the lasting machine that combines the upper with the insole by gluing in the production of upper shoes, including the lasting machine and the lasting machine. 2 Normative referenced documents
The clauses in the following documents are not standard clauses because they are too shallow to be quoted. It is noted that the referenced documents shall not be retroactively applied to all subsequent amendments (excluding mixed content) or revisions of this standard. However, all parties that reach a synergy based on the non-standard are encouraged to study whether the new versions of these documents can be used. The new version is suitable for the following standards: GB/195B Shape and installation specifications GD/T3766 Hydraulic system general technical conditions GB5226-1-2002 Mechanical safety equipment installation Part 1: General technical requirements GB/7932 Pneumatic system general technical requirements GB/T16769-1997 Metalworking cutting machine head spring level measurement method QB/T1525 Leather machinery product model compilation method QR/T1588.11992 Light industry machinery equipment applicable technical conditions QB/T1588.3-1992 Light industry machinery equipment applicable technical conditions QR/T1588.4-1992 Light industry machinery equipment assembly reverse technical conditions QR/T 1588.4-1993
3 Product classification
3.1 Model
Light industry machine According to the general technical conditions of coating roller
The model and specifications of the new machine shall comply with those formulated in Q month/1525. 3.2 Type
The transmission mode is generally divided into wave-driven belt machine, pneumatic transmission machine, and force-type turning machine.
3.3 Basic parameters
The basic parameters of the belt should comply with the provisions of Table 1. Table 1
Production information
Working pressure
Total power
Book specification
Double shift
Basic shift number
How to make! Technical documents and drawings requirements
QB/F1065—2004
4 Requirements
-TTKAONKAca-
4.1H Technical requirements
4.1.1 Whether the requirements of this standard are met and the approved drawings and technical documents are manufactured according to the relevant regulations.4.1.2 See the kit, the electrical components and other purchased parts should meet the requirements of each unit and have a complete certificate. Outsourced parts are imported! 4.2. Main parts
4.2.1 Live pull rod
a) Size: HB-242~TID269, hardness after straightening treatment: IRC55-~HRC60; s)
For single-rod, the live rod clamp is used as the standard, and the axis tolerance grade is 10. For effective rod, the two live rods shall have a tolerance grade of not less than 18.
The roughness of the pipe is not more than .4
4.2.2 The hardness grade of the pipe is H9
The hardness of the adjustment part is B242~HB269; the hardness of the surface is HRC55-HRC: b1
The end face vibration tolerance with the thread axis as the belt is not more than 7 levels, and the surface roughness should not be more than 0.4m:
4 .2.3 Wipe board (+ pole or)
Bottom type smashing degree HB242~HB20;
Upper, half of the school is not more than 0.3m, two flatness is not more than 0.3 front environment rain clothing should not be more than 8
Inner and other lines before the virtual fence and the bottom are also controlled: 12.4 Create the front Hua machine certificate to the needle through the adjustment of the wine adjustment mold: the arc surface formed by the front wheel seat of the shoe: 4.2.5 Cut the front book machine 4.2.6 The tensioner (upper belt, due to the manufacturer) should be consistent with the normal line of the vertical wheel of the cabinet: 4.3 Assembly quality
4.3.1 The full assembly degree shall comply with the relevant provisions of QB1588.3-1997. 4.3.2 The clearance of the front wheel is 0.02mml-0.03mm4.3. 3. The minimum distance between the sliding point of the front helper and the tip of the front helper should not be greater than 1mm4.3.4 The head of the mobile phone should be able to move with a light, not a dead point, and the distance between the head and the board should not be greater than 0.08mm.4.3.5 The light pin can be adjusted when the light is in place, and the front wheel of each test station should be highly consistent, and the actual needle space should not be mutually coordinated: the sealing concave food recording is active, and the effect is coordinated, and there is no movement. To correct the school and rate inspection, the lower door should not be greater than 1.5, and the inner support platform should be m~12mm.
4.3.6 The lock of the front helper and the rear of the machine should be tightened with a space to ensure that it will not move. 4.3.7 The electrical parts are arranged in an orderly manner and the wiring is clear. The oil pipes, lubrication check valves, flow control valves, solenoid valves, etc. are installed around the cows, without any trees, no secretions, and no image.
4.3.8 The installation should comply with the relevant provisions of QB/T1588.1-1902: 4.4 Overall performance
4.4.1 Normal operation, accurate action, flexible. 4.4.2 Fluid: 1 System components comply with the relevant provisions of GB/T3766. 4.4.3 After the machine is running for 2 hours, the temperature of the fluid and oil should not rise by more than 3%. .4.4.4 The pneumatic system shall comply with the provisions of (7B/7932-197). 4.4.5 The continuity of the protective earthing circuit shall comply with the requirements of 8.2.3 of CB5226.1-2002 QB/T1065-2004
4.4.6 The resistance of the square circuit shall not be less than 1M2. 4.4.7 The conductors of the new circuits of the gas change shall be subjected to at least 1n, 1000V of the production test only. The control disconnection shall comply with the provisions of (6.4 of B5226.1-2002) for the protection of the uncontrolled voltage test. 4.4.8 The machine odor is not greater than 85dB43. 49 For heating, the heating delivery system should be well matched with the nozzle and plunger, flexible and leak-free, and equipped with a residual glue recovery device. 4.4.11 The glue delivery is accurate, the action is smooth, and the delivery is smooth. 44.12 The pressure of the front frame machine is divided into two parts, the first is the pressure of the safety umbrella and the second is the pressure of the current station. 4.4.13 PLC standard machine should have various control parts, low maintenance and cumulative system Protection and safety protection functions: The equipment should be in the form of human-machine dialogue, with a good interface, easy to understand, simple to set up, and accurate in operation. Typical:
4.5 Load test
The rear of the equipment should be in a straight line with the shape of the cypress, neat and tidy, without any internal or external signs, and provide a fat sweeper. The quality should meet the requirements of the above.
4.6 Appearance quality
4.6.1 The coating and other parts should meet the requirements of 3.1.1, 3.1.2.3.11 The surface of the parts shall be smooth, shiny and free of rust and blister. 4.6.3 The parts shall be installed without rust. 5.1 Test method 5.1 Material quality 5.1.2 The hardness tester shall be used for testing and shall meet the requirements of 4.2.16), 4.2.2b) and 4.2.3. 5.1.34.2.1、4.2.2的检查 5.1.44.2.1、4.2.24）、4.2.3面材料赠切检验，用表南扣损只检验浆 or 月面植走势比较块比较
5. 2 组件质量通
5.2.1表配精流接 定定。 5.2.2 1.3.2、4.3.3、4.2.4.4.3.5的闻脱用案以效检验 5.2.3 4.3.5的炎错同内选台起旺格检验 5.2.4 4.3.6、4.3.7的检验为感识风险，以贡献包括： 5.2.5 Quality inspection of the equipment shall be carried out in accordance with the provisions of QD/T1588.1-1992. 5.3 Performance of the whole machine
5.3.1 The inspection of the hydraulic system shall be carried out in accordance with the relevant provisions of GR/T3766. 5.32 The inspection of the hydraulic system shall be carried out in accordance with the provisions of GR/T3766. 5.3.3 The continuity of the grounding circuit shall be carried out in accordance with 19.2 of GB5226.12002. 5.3.4 The electric muscle pull test shall be carried out in accordance with the requirements of GB5226.12002-:9.3. 5.3.5 Endurance test GD5236.1-3002 19.4 cost efficiency 5.3.6 Noise test, old products in the machine 1-start operation according to GB/16769-1997 method 5.3.7 daily surface temperature timer or surface temperature control test. QB/T1065-20C4 5.3.B 4.4.1, 4.4.10 ~ 4.4.13 adopt the test, and should meet the relevant requirements. 5.4 Load test
-TYKAONTKACa-
Each unit shall be tested for at least 0 pairs of belts, and all of them shall meet the requirements of 4.S. The belt surface material used for the test shall be leather and cloth.
5.5 Appearance quality
Official inspection
6 Inspection rules
6.1 Inspection classification
Output inspection and type inspection. 8.2 Factory inspection
6.2.1 The product of the production batch shall be inspected one by one before delivery: [! Factory inspection items are 4.3.2--4.3.5.4.3.7 and 4.4.66.2.2 During factory inspection, the product shall be operated under load for 4-5:82.3 The product shall be inspected by the inspection department: The inspection department shall issue the product certificate 1. 6.3 Type inspection
6.3.1 Type inspection items shall be the requirements of Chapter 4. 6.3.2 Type inspection shall be conducted in the following circumstances: a) When the product, material or process is changed significantly b) When the production is stopped for more than one year
6) When the new product is tested and evaluated
d) When the product quality inspection agency proposes a request for type inspection. 6.3.3 Type inspection shall be conducted by sampling one batch from the batch of qualified products inspected by the factory. 6.4 Judgment rules and re-inspection rules
.4.1 When a test item fails, the item shall be cleared and the item shall be qualified after re-inspection. 6.4.2 When a type inspection item fails, double sampling shall be conducted and the unqualified item shall be inspected. If it still fails, the type inspection shall be judged as unqualified.
7 Marking, packaging, transportation, storage
7.1 Marking
7.7.1 Each belt should be clearly and obviously marked with the national label. 7.1.2 The label should include the following information:
a) Product name, number and trademark:
b) Product main technical parameters:
) Belt manufacturer name;
) Production date and expiration date.
7.2 Packaging
7.2.1 The outer surface of the packaging box should be marked with:
a) Product name and serial number:
6) Manufacturer name and factory number:
c) Gross price:
d) Shipping station and arrival station, shipping and receiving units. 7.2.2 Packaging Considerations Ensure that the storage period of the machine in the indoor non-lifting box is not less than…-years: 7.2.3 The following driving characteristics are produced in the box: 4
Product certification
Instructions for use:
. 3 Transportation
Avoid violent movement, rust, and preset conditions, and use safe and reliable transportation tools. .4 Storage
QB/T10652004
The product should be placed in a dry, wind-free, rain-proof place, and should be placed steadily: The product should not rust during the specified storage period.2 If one item fails in the type inspection, double sampling shall be conducted and the failed item shall be inspected again. If it still fails, the type inspection shall be judged as failed.
7 Marking, packaging, transportation and storage
7.1 Marking
7.7.1 Each belt shall be clearly and obviously labeled with the national production license. 7.1.2 The label shall include the following information:
a) Product name, number and trademark:
b) Product main technical parameters:
|) Belt manufacturer name;
|) Production date and expiration date.
7.2 Packaging
7.2.1 The outer packaging box should be marked with:
a) Product name and serial number:
6) Manufacturer name, factory number:
c) Gross price:
d) Shipping station and arrival station, shipping and receiving unit. 7.2.2 Packaging Consider ensuring that the storage period of the machine in the indoor non-lifting box state is not less than...-years: 7.2.3 The following driving characteristics of the machine in the packing box: 4
Product certification
Instructions for use:
. 3 Transportation
Avoid violent movement, damage, and preset conditions, and adopt safe and reliable transportation tools. .4 Storage
QB/T10652004www.bzxz.net
The product should be stored in a dry, wind-free and rain-proof place and should be kept stable: the product should not rust during the specified storage period.2 If one item fails in the type inspection, double sampling shall be conducted and the failed item shall be inspected again. If it still fails, the type inspection shall be judged as failed.
7 Marking, packaging, transportation and storage
7.1 Marking
7.7.1 Each belt shall be clearly and obviously labeled with the national production license. 7.1.2 The label shall include the following information:
a) Product name, number and trademark:
b) Product main technical parameters:
|) Belt manufacturer name;
|) Production date and expiration date.
7.2 Packaging
7.2.1 The outer packaging box should be marked with:
a) Product name and serial number:
6) Manufacturer name, factory number:
c) Gross price:
d) Shipping station and arrival station, shipping and receiving unit. 7.2.2 Packaging Consider ensuring that the storage period of the machine in the indoor non-lifting box state is not less than...-years: 7.2.3 The following driving characteristics of the machine in the packing box: 4
Product certification
Instructions for use:
. 3 Transportation
Avoid violent movement, damage, and preset conditions, and adopt safe and reliable transportation tools. .4 Storage
QB/T10652004
The product should be stored in a dry, wind-free and rain-proof place and should be kept stable: the product should not rust during the specified storage period.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.