standard classification number
Standard ICS number:Household and commercial equipment, entertainment, sports>> sports equipment and facilities>> 97.220.30 Indoor sports equipment
Standard Classification Number:Light Industry, Culture and Living Goods>>Culture, Education, Sports and Entertainment Goods>>Y56 Sports Goods
Some standard content:
ICS 97.220.30
Classification number Y56
Light Industry Standard of the People's Republic of China
QB/13653—1999
Replaces ZB/TS6011987
Badminton racket
Bailrnintanrackct
Published on April 21, 1999
State Bureau of Light Industry
1 999-04-21 implementation
QB/T3653-1999
This standard is the original light professional standard ZBT56001-1987 "Badminton racket" (this standard was issued by the Ministry of Light Industry in the form of document T19991112 and converted into standard number QB3653-1999, the content remains unchanged), this standard is issued by the Industry Management Department of the State Bureau of Industry and this standard is issued by the National Document Supplies Standardization Center. This standard was drafted by the original badminton racket special standard drafting group. The main drafters of this standard are Xuan Wenjie and Sheng Yuan. From the date of implementation, this standard will replace the original light industry professional standard 26001-1987 "Badminton racket" issued by the Ministry of Light Industry. Badminton racket
This standard applies to badminton rackets for competitions and various sports and fitness. This standard applies to the International Badminton Federation 1955-[986] Competition Rules of the Badminton Federation 1 Specifications
1.1 Badminton racket parts are shown in Figures 1 and 2.
Refers to the total length www.bzxz.net
Figure 1 Wooden frame steel pole badminton racket
Total length of racket
Figure 2 Other material badminton racket
QB/T3653-199a
QE/T3653-1999
The total length of badminton racket shall not exceed 670mm
1.3 The materials of the various components of badminton racket are not specified 1.4 The length of the string surface of the badminton racket for competition shall not exceed 28mm: the width shall not exceed 220mm, 2 Technical requirements
21 The products are divided into three levels: superior products, second-class products and qualified products based on the national standards and performance. 2.2 Technical requirements should comply with the provisions of Table 1.
Folding name pin
Symmetrical point code
Form volume",
Flat point length,
Reverse railing length, mm
Height, mm
This cup of tea
Aluminum alloy frame
Excellent product
.0.110
.0.290
Five-point flat 6
:0 125
No material is too rotten, no tendons,
joints, no luster, bubbles and whitening
color ring is uniform and shiny
color is uniform, no color,
clear. No color return, no embedded element. No pitting
The racket can be symmetrical, the racket is folded on the west side of the center line, the difference is strong, the net quality, the first-class racket body is flat and small, including the racket industry, the technical performance should meet the requirements of Table 2,
refers to the name of the probe
! Static pressure is,
fear of hitting rate
add droop, nm
Deterioration, m
Electrical layer corrosion
2.4 The strength of each tax shall comply with the provisions of Table 3.
Finished products
Heart lining (Bh)
Bright, light points, small light
Qualified products
The material has no separation, no juice
With 3mm or more of the section,
The paint layer has no bright fruit flow and gas
No star moonlight
Qualified products
Level 6 (4)
Indicator name
Tensile strength, N
Diameter. mun
Yangchangqiang
Jinya mixed today
[5015kz
2.5 The product has a shelf life of one year under the specified storage conditions. 3 Test method
Variety classification
Nylon string (straw strand)
2200 (20kg)
The full length of the racket is measured with a steel ruler, and the deviation value of the symmetrical point of the racket is 0. The vernier caliper is used to measure. 3. 2 Weight
Measured by measuring (sensing 0,2).
3.3 Balance point
Q8/T36531999
180 (18g
Put the free throw racket flat on a fulcrum of the measuring tool to keep the racket body balanced, and then measure the length from the fulcrum to the end of the racket body (see Figure 3) ten points
ten points
3.4 Rebound force test
Put the racket From the bottom of the racket to the 100mm~120m part, the upper end is fixed with a ball of 26mm diameter, 40mg weight, and 250mm hip length. The ball falls naturally from the water level and is impacted ten times. When it hits the racket net five times, calculate the average value of the rebound angle (the angle with the vertical). However, in order to make the front end contact the racket net in the vertical position, it must make an angle with the racket net surface:
QB/3653-1999
3.5 Degree of deflection
3. 5. 1 Degree of deflection
Use a piece of board to draw a straight line in the middle, align the center of the handle of the racket and the center of the two holes at the top of the racket with the straight line, and then observe that the deviation between the two holes at the top of the racket handle and the straight line does not exceed 2.2. The indicators specified in the table (5) are as follows (see Figure 5). 3.5.2 Place the racket flat on the ground, use a tape measure to measure the width between the top of the grip and the half of the back, and the positive and negative measurements shall not exceed 2.2 of the specified indicators in 1 (G) (see Figure 6): \ Plate
3.8 Electroplating Etching Test
European parts (outlet)
Use the original SG2B9-193 "Test of the resistance of metal plating and chemical treatment layers of daily hardware products" Method Neutral penetration test and original 5G309-1983 daily hardware products gold exhibition mirror number full cooperation test system package negotiation method 3. 3.7 Racket support test
Place the racket rod on two fulcrums with a middle distance of 240mm, apply static force at the center of the racket rod, and its lower dimensions meet the requirements of Table 2 in 2.7, then remove the pressure, measure the difference between its deformation and the original position (horizontal line), and meet the requirements in 2.3 Record 2 (see Figure 7).
3.B Racket pull test
Institute pressure
QB/T 3653-1999
Take a blade-length guard, one end is tightened on the quality frame, and the other end is pulled by the force control device. The length index is set as specified in Table 3, and it needs to break. 3.9 Appearance 4 Inspection rules 4.1 Delivery inspection Each batch of products shall be inspected by the quality inspection department according to this standard before delivery. Only those that meet the standard shall be shipped out of the factory. 4.2 Acceptance test 2.2. This test shall be carried out by the ordering party together with the quality inspection department of the manufacturer. 4.2.2 This test is based on the "Batch Inspection Counting Sampling Sequence and Sampling Table" in 2838-1981: - Check the balance of the stock! One-stop inspection sampling plan
4.2.3 The sequence of test items and their AOL values shall be carried out in accordance with the provisions in Table 4. Table 4
The racket will only have a balance point length. 4.3 Type test
Sincerely hope that the force law tea money
Superior products
First-class products
4.9.1 This test is carried out by the quality inspection department of the power production plant: the ordering party can register a representative to participate when necessary. Qualified products
4.3.2 This test sample should be randomly selected from the qualified batch of delivery, and then all the items specified in the delivery test will be inspected on the same day. If unqualified products are found, they will be replaced with qualified products,
4.3.3 This or inspection is carried out once every 6 months, and sent to one of the following estimates. The test should also be carried out. QB/T3653-1S99
More efficient design:
Change key process:
Change main materials:
Quality is unstable:
) Stop production for more than 1 month and restart production. 4.3.4
This test plan is based on the periodic inspection counting procedure of G02829-1981 and the modified periodic inspection in Table 3.
Type test items and RQL. values should be carried out according to the specifications in Table 5. Table 5
Judgment level
Test source
Test items
Rebound force test
Electrode corrosion test
Guard rod elasticity test
Summary control and inspection
5Marking, packaging, transportation hook, storage
Excellent and
5.1. The racket should be affixed with trademark, brand, model and certificate. 5.2 Badminton rackets should be packed in wood or grain. The name, quantity, factory name, article number, weight, volume, and origin should be marked on the outside. 1. Avoid moisture and handle with care (except for foreign products) 5.3 After packing, badminton rackets should be stored in a warehouse with good air exposure to avoid moisture and pressure. 5.4 During transportation, avoid rain, sunlight, and pressure, and handle with care.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.