Some standard content:
I0S 39.040
Classification number: Y11
Adoption number: 16397-2005
Light Industry Standard of the People's Republic of China
QB/T1541-2005
QB/1541-1992
Sterl bars and wires for locks
Sterl bars and wires for locks2005-07-26Published
Implementation on 2006-01-01
Published by the National Development and Reform Commission of the People's Republic of ChinaForeword
4 Is the markup for QB:T1541-1992 Sterl bars and wires for locks? The main differences of this standard QR/T15411992 are as follows: cancel the common terminology; standardize the classification, specification and marking methods; cancel the uncommonly used specifications (4.2): the maximum limit of the shape, roundness and linearity of the material are adjusted according to the overall needs (4.3). This standard will be issued by the China Light Industry Association. This standard is the National Clock and Watch Standardization Center. |This standard is issued by the Industrial Clock and Watch Research Institute. The standard is mainly composed of Liu Kechong and Yang Du. The standard replaced by the standard version: QR8781983.QR/T1541-1992
QB/T15412005
is not a standard, but replaces the original light industry standard QB/T1541-1992 needle steel and wire, 1 range
clock steel and wire
QB/T 15412005
This standard specifies the classification, requirements, test methods, inspection rules and marking, packaging, transportation and storage of various steel samples and steel wires (referred to as "steel samples, wires").
This standard is used to manufacture steel samples and wires for clothing parts, and can also be used in the daily machinery industry such as instruments and meters. 2 Normative references
The following documents have become the terms of this standard through their reference in this standard. The following are references by date, and their subsequent revisions (excluding the contents of the reference) are not applicable to this standard. However, the latest versions of these documents can be used for products that have reached an agreement based on this standard. The official documents without date are the latest versions applicable to this standard GB/1223.1 Determination of carbon content in iron and alloys. GBT228 Tensile test method for steel materials at room temperature GBT2103 Steel acceptance, packaging, standard state and quality indication 15 General provisions GB14340.1 Steel test method Part 1: Test method GBI10G10 Product geometry specification Table station average rate method to assess the surface rate structure rules and methods 3 Classification, specifications and end marks
3.1 Classification
3.11 Classification of steel shapes
Material shape:
Wire-shaped.
31.2 Classification of steel grades
Reduction 1.H steel T9A:
High quality carbon reduction 1.5, 70, 65mm:
Carbon structure Q235A, Q235B
3.1.3 Classification by state
3. 1. 3. 1 Hardness
Di (Y):
Comparative (M>:
3.1.3.2 Stress resistance
Chuanzhu,
3.2 Specifications
3.2.1 Some small sizes of wire are shown in Table 1.1
QBT1541·2D05
0.55..40.0.50.50#.55..60.2.70.0.802.90,1.00,130,1.30.1.40.150,1.60,1.70,180-2:00,2.20-2.50-2.80-3.00,3.30,3.504.00,.505.n0,559r..6.5.7.00. 7.50.8 00 till: the return has its own fee request, the supply and demand parties agreed on the date, copper wire
E800-32U0
3.2.2 price reduction for goods, each set is allowed to deliver indefinite length short pieces, the reward should be no less than 11500m1 purchase three not more than 15% 3.3 note
steel wire product table: note:
procurement number
) use special %: 5 certificate manufacturing process is 4.00mm, the self-property difference is grade auction village. Certificate: 1A grade 4, (1154!
, for 14, group, straight light for .5m selected internal material: T9ATB 40.50QB-T154L2005
Chemical composition
Copper control, reverse chemical theory should be priced in Table 2 Specification Table 2
Gold medal number
: 0.12.~0:19
0.12~heart.22
c..2--0.20
[ h,--
nx.n.91
0.35 ~0.6
0.30~0.65
0.30--0.70
0.90...1.2c
: 1-1>
0.17.-.0.37
% ()
4.2 Appearance
Steel pants, the maximum diameter of the product, the surface ... 2 period, the tensile strength of the wire needs to meet the requirements of Table 1.5. A.70,65Mn
15 Q235
4.4 appearance
high rmma
printed Guangpi HV
Anhui dense supply and demand
capital negotiation,
all over Sichuan remember you
QB/T154°—2005
egg dense ancient Mao
self-extracted
anti-type degree a
200--2509
4 .4.1 The surface of the copper wire should be flat and large, and should not have cracks, cracks, overlaps, pull marks, gas marks, impurities and rust. 4.4.2 The copper wire surface should have slight scratches, scratches, vertical objects, spots and other defects. The area should not exceed 10% of the surface area, and the depth should not exceed 10% of the treatment height difference. 4.4.3 The surface of the copper wire should meet the requirements of QB/T1541-2005
15 Q235
T9A. 7n, G5M-
Test method
5.1 Chemical composition
Si4 steel shall be selected, the chemical composition shall be determined according to the method of GB/T223.1, and no analysis is required. 5.2 External
3.00--6.co
5.2.1 [The sound vibration limit of some steels shall be measured with a scale of 0.00mm according to the difference points. 522 The test platform shall be used to observe whether the steel has obvious vibration when it is dropped. 53 Mechanical properties
5.3.1 The Vickers accuracy test of the sample shall be carried out according to the method of GB/4340.1. 53.2 The temperature tracking test of silver bars and wires shall be carried out with a controlled force meter according to the method of GH228. 5.4 Appearance
5.4.1 The visual acuity of the outer double eyelid shall be measured daily,
the fabric weight
5.4.2 The thickness of the outer surface shall be tested according to the normal core force. If necessary, the wheel rate shall be only 0B 10610. 6
Inspection rules
6.1 Ten inspection items
connection, thread will be specially inspected. 6
inspection items F
North School
Ze 2:
must be the most eliminated
ask the breast and thickness
touch the hair
"," for the system,
|“U.S. inspection step:
For stress
“Wide” for supply, “supervision” for demand, batch
Change delivery supervisionbzxZ.net
QB/T1541-2505
Thank you, finally should be a light inspection (received) form, the batch should be in shape, still present, the same brand,: to the state that is considered.
6.3 Sampling
6.3.1 Chemical virtual inspection, for delivery inspection, a sample should be taken from each sample during the smelting process; for gram supervision, a test bar should be taken from the car batch product attached to the machine
6.3.2. Dimensional inspection, tensile strength inspection, external inspection, appearance inspection, each batch of products shall be inspected according to the whole inspection, B.4. 8.4.! The inspection shall be detailed for all items! The inspection shall be comprehensive for this product. 6.4.2 If any item is unqualified, the neutral sample of the batch of products can be selected for the unqualified items for a second inspection. If there is one unqualified item in the second inspection, the product shall be qualified. 65. Post-inspection disposal
6.5.1 After the acceptance inspection, the unqualified batch of products shall be inspected by the industry certificate (reputation): the qualified products have been inspected and accepted by the group. 6.5.2 After inspection, both parties shall mark, pack, transport, purchase and store the steel, and the final mark, express, storage and calibration shall comply with the relevant requirements of B/T2103.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.