title>HG 5-757-1978 Steel frame agitator (trial) - HG 5-757-1978 - Chinese standardNet - bzxz.net
Home > HG > HG 5-757-1978 Steel frame agitator (trial)
HG 5-757-1978 Steel frame agitator (trial)

Basic Information

Standard ID: HG 5-757-1978

Standard Name: Steel frame agitator (trial)

Chinese Name: 钢制框式搅拌器(试行)

Standard category:Chemical industry standards (HG)

state:in force

Date of Implementation:1997-01-01

standard classification number

Standard Classification Number:Chemical Industry>>Chemical Machinery and Equipment>>G92 Chemical Machinery

associated standards

Publication information

other information

Introduction to standards:

HG 5-757-1978 Steel frame agitator (trial) HG5-757-1978 standard download decompression password: www.bzxz.net

Some standard content:

Ministry of Chemical Industry of the People's Republic of China
Ministry Standard
Steel Frame Agitator (Trial)
I. Type, basic parameters and dimensions
HG 5 -757—78
1. The type, basic parameters and dimensions of steel frame agitators shall comply with the provisions of Figures 1 to 4, the detailed table and the dimension table. Carbon steel
Promulgated by the Ministry of Chemical Industry of the People's Republic of China and proposed by the Chemical Machinery Research Institute of Lanzhou Chemical Industry Corporation
Trial implementation on October 1, 1981
HG 5-757--78
++ + -www.bzxz.net
Dr ≥1340
Stainless steel
HG5—75778
Dys1140
wwW.bzsoso:com757
THG5-75778
Note: The bottom of the agitator is elliptical h1: D1=1: 4758
Horizontal beam
Through the shaft bolt
Connecting bolt
Upper beam
Lower beam
(40)
HG 5-757-78
1Cr18Ni9Ti
Di≥1340
1Cr18Ni9Ti
: The figures in brackets are the relevant quantities of stainless steel frame agitators. Note:
1Cr18Ni12Mo2Ti
1Cr18Ni12Mo2Ti
GB45—66
GB18-66
GB45—66
GB1866
GB45——66
GB18—66
GB45—66
GB18-66
T- 759 -m
5-757-78
880°0
880°0
880°0
880°0
880°0
880°0
-05—757 -78 | 5--757--78
II. Technical requirements
2. The outer edge of the upright blade of the frame agitator should be symmetrical with the center line of the shaft hole, and its asymmetry is 4/1000 of the diameter D of the blade; its deflection from the center line of the shaft hole is 4/1000 of the blade height H, and shall not exceed 5 mm. 3. The welding form of the reinforcement part shall be intermittent welding. If integral welding is required, it can be indicated. 4. D1340 mm is generally detachable. If required by the use situation, it can be indicated whether it needs to be detachable. III. Explanation
5. This standard is recommended for the stirring of liquids in non-uniform systems with a viscosity of less than 15,000 centipoise and a weight of less than 2000 kg/m". For example: it is used to dissolve crystalline, non-crystalline, and fibrous materials, keep solid particles in suspension and fibrous materials in a uniform suspension state, polymerize viscous materials such as polymers, prevent precipitation and material adhesion to the wall, and perform heat exchange.
6. Agitators with D ≤ 1140 mm can be installed upside down due to process requirements. 7. The diameter dimensions of the agitators recommended by this standard are shown in Table 3. Recommended diameter dimensions of frame agitators (mm) Container diameter D
8. Marking example:
Agitator
A frame agitator with a diameter D of 1140 mm, a shaft diameter d of Φ65 mm, and 1Cr18Ni9Ti is marked as: Agitator I1140-65HG5-757--78. --764-
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.