JB/T 10209-2000 This standard specifies the test methods for the geometric accuracy and working accuracy requirements of comb-tooth tenon mortising machines. This standard applies to general-purpose comb-tooth tenon mortising machines. This standard was first issued in August 2000. JB/T 10209-2000 Comb-tooth tenon mortising machine accuracy JB/T10209-2000 Standard download decompression password: www.bzxz.net

1CS 79.120.20
Machinery Industry Standard of the People's Republic of China
JB/T10209-2000
Finger jointing machines without glutng operation-Precision
2000-08-31 Issued
National Bureau of Machinery Industry
2001-01-01 Implementation
JB/T10209—2000
This standard is based on the current precision of the toothed joint opening mechanism in the domestic industry, and at the same time examines the domestic market demand, and is supplemented and adjusted.
This standard is proposed by the National Technical Committee for Standardization of Machine Tools and Cutting Tools. This standard is under the jurisdiction of the Tianjin Woodworking Machinery Research Institute. The responsible unit of this standard: Tedanjiang Woodworking Machinery Factory. The main drafters of this standard are Sui Yanwen and Guo Hongyu. 1 Scope
Machinery industry standard of the People's Republic of China
Comb opening machine accuracy
Finger folotine mains withowtgluiog operationPrecion
This standard specifies the requirements and inspection methods for the geometrical dimensions and working accuracy of comb opening machines. This standard is applicable to comb opening machines for a certain purpose: 2 Reference standard
JBTT10209-2000
The clauses included in the underlined labels are used in this standard and constitute the clauses of this standard. When this standard is issued, the version indicated is valid. All standards are subject to revision, and parties using the standard should use the latest version of the following standards whenever possible. 1B:T4171-1999 Machine Tool Precision Inspection 3-General Requirements
3.1 The use of this machine tool shall comply with the provisions of JBT41. 3.1 During the inspection of the machine tool, adjust the installation level of the machine tool according to 3.1 of 1T4171-1999, place the level gauge in the middle of the machine tool workbench, and the vertical and horizontal readings of the level gauge shall not exceed 0.1/1000. 3.3 When the actual measured length is different from the length specified in the water standard, the tolerance shall comply with the provisions of 2.2.1.1 of JB Jin 4171·1999. Length conversion, the minimum conversion value is 0.01mm, 3.4 The order of each dimension test listed in this standard does not represent the actual test order. In order to facilitate the disassembly and inspection of machine tools, the test can be carried out in any order. 4 Geometric accuracy inspection. Geometric accuracy and inspection methods shall be in accordance with the provisions of Table 5 Working accuracy inspection. Working accuracy and inspection methods shall be in accordance with the provisions of Table 2. National Machinery Industry Drawing 2000-08-31 Approved 2001-01-01 Purchase JB/T102092000 tt||Surface geometry inspection
Inspection bearing
Workbench surface plane
Workbench in
water surface
Movement path along the guide shaft
Workbench group
Movement to the working
piece
Spindle radial
Yinxiao movement
a) Aluminum shaft
b) Extra small shaft
Spindle continent
Return movement
Positioning
In 10 00 reward
straight length
at 1000 measurement
maximum length
at 1000
length! For
inspection tools
equal height
indicator
equal excitation block
indicator
indicator port
inspection method transmission servicebZxz.net
1 day/T1171 has American * text
4.2.3.1.2.2
4.4.2.2.2.1
JB/T 10209-200 No. 1 (Complete) Inspection Items Small Axis Axis Direction Saw Axis Rotation Plane and: Verticality of Working Table Surface Offset Axis Rotation Plane and Working Table Position Push Plate Verticality of Special Axis to Working Table Surface Quick Axis Return Light Radius 100 for Control H Indicator Test plate
Point angle ruler
Indicates
Test method: Your membrane
Relevant provisions of B417
4.71.2.2.4
4.7.1.2.2.4
4.7.12.3.2
In the baking direction of the workbench,
Pushing direction test slurry
JB/T10209-2000
Test items
Sugar cutting surface
To the base
Vertical bottom
Two mourning measures
Together tooth joint
Food space fan
In 100 long!
True angle ruler
Test method should be based on the relevant document of JB/T417[. The largest of the two measuring plates is the test value.
1 The moisture content of the test piece is not more than 5% of any kind of dyeing technology. 2 The specification of the test piece is 41x100× (not less than 90% of the maximum working height of the machine): 1. The part shall not have any shadow of the quality. 3 The plane extension length of the test surface is o.tomm. 4 The test tool meets the relevant US regulations.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.