This standard specifies the series spectrum of power cable accessories with rated voltage of 265 kV and below. This standard applies to the classification and series division of power cable accessories with rated voltage of 265 kV and below (hereinafter referred to as power cable accessories), and guides product development and application selection. JB/T 6467-1992 Series spectrum of power cable accessories with rated voltage of 26/35kV and below JB/T6467-1992 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
Series and Types of Power Cable Accessories with Rated Voltages of 26/35kV and Below 1 Subject Content and Scope of Application
This standard specifies the series and types of power cable accessories with rated voltages of 26/35kV and below. JB/T 6467~92
This standard applies to the classification and series division of power cable accessories with rated voltages of 26/35kV and below (hereinafter referred to as power cable accessories), and guides product development and application selection. 2 Reference Standards
GB2900.10 Electrical Terminology Part 10 Wires and Cables GB11033
3 Terminology
Basic Technical Requirements for Power Cable Accessories with Rated Voltages of 26/35kV and Below 3.1 Except as provided in this standard, all terms shall be defined in GB2900.10 and GB11033. 3.2 Power cable accessories
The power cable accessories specified in this standard refer to various joints and terminals of power cables with rated voltage of 35kV and below. 3.3 Wrapping cable accessories
Cable joints and terminals formed by wrapping self-adhesive rubber tape around the treated cables at the installation site. 3.4 Heat shrinkable cable accessories
Cable joints and terminals formed by heating and shrinking heat shrinkable components (including various pipes, gloves and rain covers, etc.) on the treated cables at the installation site.
3.5 Cold shrinkable cable accessories
Rubber components with internal supports (including joint sleeves, terminal sleeves and gloves, etc.) are put on the treated cables at the installation site, and the supports are pulled out to shrink them tightly to form cable joints and terminals on the cables. 3.6 Prefabricated assembled cable accessories
Cable joints and terminals are formed by using rubber pre-molded parts (including joint sleeves, terminal sleeves, stress cones and rain covers, etc.) to be put on the treated cables at the installation site. 3.7 Prefabricated plug-in cable accessories
Cable joints and terminals are formed by using rubber pre-molded parts (including joints and terminal parts) to be first put on the treated cables and then inserted into electrical equipment or cables to be plugged into each other. 3.8 Resin cast cable accessories
Cable joints and terminals are formed by using thermosetting resin materials to be cast on the treated cables at the installation site. 3.9 Molded cable accessories
Cable joints and terminals are formed by using strips that are the same or similar to the cable insulation, wrapped around the treated cables at the installation site, and heated and pressed by molds.
3.10 Cast-in-place cable accessories
Cable joints or terminals formed by pouring liquid or heated fluid-like insulating materials into the assembled cable accessory housing at the installation site.
3.11 Equipment-type terminals
Approved by the Ministry of Machinery and Electronics Industry on August 6, 1992 and implemented on January 1, 1993
JB/T646792
Equipment-type terminals refer to cable terminals with cable terminal components or cable terminal parts on the structure of the connected electrical equipment. 3.12 Porcelain-sleeved terminals
Cable terminals using electrical porcelain materials as external insulation. Classification of power cable accessories
Power cable accessories
The classification of power accessories is as follows:
Series spectrum
5.1 Terminals
Design-type terminals!
Outdoor terminal
Weighted type
Prefabricated plug-in type
Resin casting type
Prefabricated assembly type
Cold shrinkage type
Heat shrinkage type
Wrapping type
Casing type
Injection type
Porcelain sleeve type
Resin casting type
Prefabricated assembly type
Cold shrinkage type
Heat shrinkage type
Wrapping type
Injection type
Porcelain sleeve type
Over-splash type joint,
Conversion type joint!
Oil plugging type
Branch type connector,
Straight type connector
Plug box type
Resin casting type
Heat shrink type
Wrapping type
Resin casting typewww.bzxz.net
Cold shrink type
Turnkey type
Resin washing type
Stop box type
Wrapping type
Resin casting type
Plastic replacement type
Additional instructions:
JB/T 646792
This standard is proposed and managed by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry. This standard is drafted by Shanghai Cable Research Institute of the Ministry of Machinery and Electronics Industry and Cable Accessories Professional Committee of Wire and Cable Association of China Electrical Equipment Industry Association.
The main authors of this standard are Ge Guangming and Zhou Mingyang. 69
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.