title>JB/T 7738-1995 Outrigger electric rock drill - JB/T 7738-1995 - Chinese standardNet - bzxz.net
Home > JB > JB/T 7738-1995 Outrigger electric rock drill
JB/T 7738-1995 Outrigger electric rock drill

Basic Information

Standard ID: JB/T 7738-1995

Standard Name: Outrigger electric rock drill

Chinese Name: 支腿式电动凿岩机

Standard category:Machinery Industry Standard (JB)

state:Abolished

Date of Release1995-06-20

Date of Implementation:1996-01-01

Date of Expiration:2007-07-01

standard classification number

Standard Classification Number:Machinery>>General Machinery and Equipment>>J84 Rock Drilling Machine

associated standards

alternative situation:Replaces ZB J84017-89; replaced by JB/T 7738-2006

Publication information

publishing house:Mechanical Industry Press

Publication date:1996-01-01

other information

Focal point unit:Tianshui Rock Drilling Machinery and Pneumatic Tools Research Institute

Publishing department:Tianshui Rock Drilling Machinery and Pneumatic Tools Research Institute

Introduction to standards:

This standard specifies the types and basic parameters, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of outrigger electric rock drills. This standard applies to outrigger electric rock drills. JB/T 7738-1995 Outrigger electric rock drill JB/T7738-1995 Standard download decompression password: www.bzxz.net

Some standard content:

Machinery Industry Standard of the People's Republic of China
JB/T7738-95
Outrigger Electric Rock Drill
Published on June 20, 1995
Ministry of Machinery Industry of the People's Republic of China
Implemented on January 1, 1996
Mechanical Industry Standard of the People's Republic of China
Outrigger Electric Rock Drill
Subject Content and Scope of Application
JB/T 7738-95
Generation Police ZBJ84017-89
This standard specifies the type and basic parameters, technical requirements, test methods, inspection rules and marking, packaging, transportation and storage of outrigger electric rock drills.
This standard applies to outrigger electric rock drills. 2 Reference standards
GB1032
GB5621
GB5898
JB1590
JB3576
JB/T3904
JB/T4041
JB/T7161
JB/T7163
JB/T7164
JB/T7302
Basic technical requirements for rotating electrical machines
Test methods for three-phase asynchronous motors
Rock drilling machinery and pneumatic tools
Rock drilling machinery and pneumatic tools
Rock drilling machinery and pneumatic tools
Rock drilling machinery and pneumatic tools
Rock drilling machinery and pneumatic tools
Rock drilling machinery and pneumatic tools
3.1 Types and basic parameters shall comply with the requirements of Table 1. Approved by the Ministry of Machinery Industry on June 20, 1995
Implemented on January 1, 1996
Rapid velocity
Impact energy
Impact frequency
Dense hole depth
Drill rod speed
Late sound (sound power level)
Rated power
Rated voltage
Insulation resistance (actual state)
No-load current
Working current
3.2 The product model shall comply with the provisions of JB1590 and the technical requirements||tt ||JB/T7738-95
mm/min
4.1 The product shall comply with the requirements of this standard and be manufactured according to the drawings and technical documents approved by the prescribed procedures. The parts of the same model product shall be interchangeable.
The general requirements of the motor shall comply with the provisions of GB755 and GB1032. After the motor stator winding is subjected to a withstand voltage test at a voltage of 1760V and a frequency of 50Hz, the insulation shall not be broken down. When the product is running without load, the deviation between any phase of the three-phase current and the average value of the three phases shall not exceed 10% of the average value. The motor insulation grade is E grade. When the motor reaches the actual stable temperature, the winding temperature rise limit is 75C (resistance method). The product shall be groundable, and the grounding wire shall be marked with a yellow-green alternating line. Lead alloy castings shall comply with the provisions of JB/T3904. Die forgings shall comply with the provisions of JB/T7163
The heat-treated parts of the product shall comply with the provisions of JB/T7161. The machined parts shall comply with the provisions of JB/T7164. The product anti-rust shall comply with the provisions of JB3576. When assembling the product, all parts and components shall be cleaned and the cleanliness value shall not exceed 350mg. All parts (including outsourced, purchased and standard parts) must be inspected and qualified before assembly. The complete set of products including the main machine, outriggers, control box and necessary spare parts and tools. The manufacturing and inspection of the control box shall comply with relevant regulations and shall have protection functions such as leakage, short circuit and overload. Inspection method
Determination of machine weight
It can be weighed with any scale that meets the regulations. 5.2
Determination of drilling speedWww.bzxZ.net
When testing the drilling speed, use a 34mm diameter drill bit to drill two holes horizontally on the rock with a compressive strength of 80-120MPa. The hole depth is not less than 1.5m
5.3 Determination of impact energy
JB/T 7738-95
The product impact energy is determined in accordance with the provisions of GB5621. 5.4 Determination of impact frequency
The impact frequency is measured on the running test bench or stress wave test bench. 5.5 Determination of 4m deep hole
When testing a 4m deep hole, use a 34mm diameter drill bit: first use a 1.8m drill rod to drill horizontally on the rock with a compressive strength of 80~120MPa, and then use a 4m drill rod to drill to a depth of 4m. 5.6 Determination of drill rod speed
The drill rod speed is measured on the running test bench. 5.7 Determination of noise
The determination of product noise shall be carried out in accordance with the provisions of GB5898. 5.8 Determination of cleanliness
The determination of product cleanliness shall be carried out in accordance with the provisions of JB/T4041. 5.9 Motor stator winding withstand voltage test
Electrify the motor stator winding for 1 minute (voltage 1760V, frequency 50Hz), and then check whether the insulation is broken down. 5.10 Determination of motor stator winding temperature rise
The determination of motor stator winding temperature rise shall be carried out in accordance with Article 5.2.4 of GB755 and the provisions of GB1032. 5.11 Determination of motor insulation resistance
In the actual cold state, use a 500V front pressure megohmmeter to measure the insulation resistance between the non-grounded end and the grounded end of the cable (or soft wire) (or between the metal parts that may be connected).
5.12 Determination of no-load current and working current of the motor The no-load current and working current of the motor can be measured on the running test bench under the condition of power supply voltage of 380V and rated frequency of 50Hz, or can be measured directly with a clamp ammeter instead of the running test bench. 6 Inspection rules
6.1 Factory inspection
6.1.1 Each product shall be inspected before delivery. It can be delivered only after passing the inspection of the factory quality inspection department, and shall be accompanied by a product quality certificate. 6.1.2 Before delivery inspection, the idling time of the product shall be no less than 20min. After delivery inspection, the cylinder body, machine head and other parts must be cleaned, and lubricating oil shall be applied to the surface of their moving parts.
6.1.3 Factory inspection items
Insulation resistance of motor stator winding to machine shaft; no-load current of motor:
Working current of motor:
Drilling speed (if inspected on the running test bench, the drill rod speed and working current shall be tested). 6.2 Type inspection
6.2.1 The product shall be subject to type inspection in the following cases: a.
When the product is produced for the first time;
When there are major changes in the structure, material and process of the product;
When it is produced in batches or in large quantities, it shall be conducted every 3 to 5 years;
When the national quality supervision agency proposes the requirement of type inspection. 6.2.2 All items of product type inspection shall be inspected in accordance with the requirements of this standard. 6.2.3
Five products for type inspection shall be randomly selected from the qualified products. 3
7 Marking, packaging, transportation and storage
Each product shall have the following markings:
Manufacturer name:
Product model and name:
Product number:
Manufacture year and month.
7.2 Packaging
The packaging shall comply with the provisions of JB/T7302.
The technical documents accompanying the product packaging should include: packing list;
Product certificate:
Product instruction manual.
Transportation and storage
JB/T773895
When transporting the product, it should be protected from rain and moisture. 7. 3. 1
7.3.2 The product should be stored in a dry and ventilated place. Additional instructions:
This standard was proposed and managed by Tianshui Rock Drilling Machinery and Pneumatic Tools Research Institute. This standard was drafted by Yichun Pneumatic Tools Factory. The main drafters of this standard are Li Chunxiu and Bo Lingjun.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.