title>Packaging containers—Aluminum easy open end and aluminum two-piece can - GB/T 9106.1-2009 - Chinese standardNet - bzxz.net
Home > GB > Packaging containers—Aluminum easy open end and aluminum two-piece can
Packaging containers—Aluminum easy open end and aluminum two-piece can

Basic Information

Standard ID: GB/T 9106.1-2009

Standard Name:Packaging containers—Aluminum easy open end and aluminum two-piece can

Chinese Name: 包装容器 铝易开盖铝两片罐

Standard category:National Standard (GB)

state:Abolished

Date of Release2009-11-30

Date of Implementation:2010-05-01

Date of Expiration:2019-12-01

standard classification number

Standard ICS number:Packaging and transportation of goods>>55.120 Cans, tins, tubes

Standard Classification Number:General>>Marking, packaging, transportation, storage>>A82 Packaging materials and containers

associated standards

alternative situation:Partially replace GB/T 9106-2001

Publication information

publishing house:China Standards Press

Publication date:2010-05-01

other information

Release date:1988-04-30

drafter:Zhu Liping, Zhou Jinchang, Lu Ming, Cai Jiansen, Chen Gang, Jin Anmin, Liu Quansheng, Lu Shiming, Li Danhe

Drafting unit:National Packaging Product Quality Supervision and Inspection Center (Guangzhou)

Focal point unit:National Packaging Standardization Technical Committee Metal Container Technical Committee

Proposing unit:National Packaging Standardization Technical Committee

Publishing department:General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China Standardization Administration of China

competent authority:National Standardization Administration

Introduction to standards:

GB/T 9106.1-2009 Packaging Containers Aluminum Easy-Open Ends Aluminum Two-Piece Cans GB/T9106.1-2009 Standard Download Decompression Password: www.bzxz.net
This standard specifies the requirements, test methods, inspection rules and marking, packaging, transportation and storage of aluminum easy-open ends and aluminum two-piece cans. This standard applies to the manufacture, use, circulation and supervision inspection of unused aluminum easy-open ends and aluminum can bodies for beer, carbonated and nitrogen-filled beverages. ||tt
|| This standard replaces the aluminum easy-open ends and aluminum can bodies in GB/T9106-2001 "Packaging Containers Aluminum Easy-Open Ends Two-Piece Cans".
Compared with GB/T9106-2001, this standard has the following major changes:
--- The name of the standard is changed to "Packaging Containers - Aluminum Easy-Open Ends and Aluminum Two-Piece Cans";
--- The scope of application is aluminum easy-open ends and aluminum can bodies;
--- The relevant provisions on steel cans are deleted from the can body part;
--- Examples of two-piece can models are added (see 4.4);
--- The quality requirements for can body and can lid coatings are increased under high-temperature sterilization conditions (see 5.2.2 and 5.3.2);
--- Sterilization test for internal and external coatings, adding the test method for high-temperature sterilization (see 6.9.2);
--- The unqualified classification of the coating quality of can bodies and easy-open ends, the sealing of easy-open ends and the opening reliability after high-temperature sterilization filling is stipulated as
Class A unqualified, and the acceptance quality limit (AQL) is 0.65 (see Table 7).
This standard is proposed by the National Technical Committee for Packaging Standardization.
This standard is under the jurisdiction of the Metal Container Sub-Technical Committee of the National Technical Committee for Packaging Standardization.
The responsible drafting unit of this standard: National Packaging Product Quality Supervision and Inspection Center (Guangzhou).
Participating drafting units of this standard: Sanshui Jianlibao Fute Container Co., Ltd., Bohua Container Co., Ltd., Qingdao Meite Container Co., Ltd., Ball Asia Pacific (Shenzhen) Metal Container Co., Ltd., Pacific Can Manufacturing (Beijing) Co., Ltd., East China United Can Manufacturing Co., Ltd., Suzhou PPG Packaging Coatings Co., Ltd.
The main drafters of this standard: Zhu Liping, Zhou Jinchang, Lu Ming, Cai Jiansen, Chen Gang, Jin Anmin, Liu Quansheng, Lu Shiming, Li Danhe. The
previous versions of the standards replaced by this standard are:
---GB9106-1988, GB9106-1994, GB/T9106-2001.
The clauses in the following documents become clauses of this standard through reference in this standard. For any dated referenced document, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties to an agreement based on this standard are encouraged to investigate whether the latest versions of these documents can be used. For any undated referenced document, the latest version applies to this standard.
GB/T2828.1-2003 Sampling inspection procedures for attributes Part 1: Sampling plan for batch inspection based on acceptance quality limit (AQL) (ISO2859-1:1999, IDT)
GB11677 Hygienic standard for water-based modified epoxy can lining coatings
GB/T4122.1 Packaging terminology Part 1: Basic

Some standard content:

1CS55.120
National Standard of the People's Republic of China
GB/T9106.1---2009
Partially replaces GB/T9106-2001
Packaging containers
Aluminum easy open end and aluminum two-piece can
Packaging containers-Aluminum easy open end and aluminum two-piece can2009-11-30Promulgated
General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of ChinaStandardization Administration of China
2010-05-01ImplementationbzxZ.net
GB/T 9106.1—2009
This standard replaces (13/06-2001 "Aluminum easy-open ends and aluminum can bodies in packaging containers with aluminum easy-open ends two-piece". Compared with GB/TJ106--2001, this standard is standardized as follows: the name of the standard is changed to "Aluminum easy-open ends and aluminum two-piece cans for packaging containers": the scope of application is aluminum easy-open ends and aluminum can bodies; the relevant provisions on steel cans are deleted from the can body part; examples of two-piece can models are added (see 4.4);
The coating quality requirements for can bodies and can lids are increased under high temperature tea fungus conditions (see 5.2.2.5.3.2); the internal and external coating sterilization test, the test method of high temperature sterilization is added (see 6.9.2); the unqualified classification of the coating quality of the seam body and easy-open lid, the easy-open seal and the opening reliability after high temperature sterilization filling is stipulated as Class A unqualified, and the acceptance quality limit is
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.