title>JB/T 9016.1-1999 Suspension conveyor traction detachable chain - JB/T 9016.1-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 9016.1-1999 Suspension conveyor traction detachable chain
JB/T 9016.1-1999 Suspension conveyor traction detachable chain

Basic Information

Standard ID: JB/T 9016.1-1999

Standard Name: Suspension conveyor traction detachable chain

Chinese Name: 悬挂输送机 牵引可拆链

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-06-28

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:Material storage and transportation equipment>>Continuous handling equipment>>53.040.20 Conveyor parts

Standard Classification Number:Machinery>>General Machinery and Equipment>>J81 Conveying Machinery

associated standards

alternative situation:ZB J81008.1-1989

Publication information

other information

Focal point unit:Beijing Hoisting and Conveying Machinery Research Institute

Introduction to standards:

JB/T 9016.1-1999 JB/T 9016.1-1999 Suspension conveyor traction detachable chain JB/T9016.1-1999 Standard download decompression password: www.bzxz.net

Some standard content:

IS53.040.24)
Machinery Industry Standard of the People's Republic of China
JB/T9016.1-9016.2—1999
Overheal conveyor chain and sprocket1999-(Published on 6-28
National Machinery Next Asia Week
2000-01-01 Implementation
#B/9016.1—1999
This standard is a revision of ZBJ81008.1—89 "Drag-and-detachable chain for overhanging conveyors". During the revision, editorial changes will be made to the original standard, but the main technical content will not change. This standard replaces ZBJ81008.19 from the date of implementation. This standard is produced and imported by Beijing Hoisting and Conveying Machinery Research Institute. This standard was drafted by: Beijing Hoisting and Conveying Machinery Research Institute. Scope
Machinery Industry Standard of the People's Republic of ChinabzxZ.net
Overbead conveyorDrag rlveil essehalinThis standard specifies the types, basic parameters, dimensions and technical requirements of detachable chain for overhanging conveyors. This standard is applicable to ground conveyors. 2 Reference standards
JH/T 9016.1-1999
The new provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. The service provider who uses this standard should consider the possibility of using the latest version of the following standards. GB.T9785-1988 Chain and sprocket technology
3 Types, basic parameters and dimensions
3.1 The detachable armor of the conveyor chain adopts two structural types: die forging chain (Figure 1) and stamping chain (Figure 2), and two types of structure. 3.2 The basic parameters and dimensions of the detachable load should comply with the requirements of Figure 2 and Table 2. It is recommended to use the standard of "10". The National Machinery Industry Bureau approved the shaft on June 28, 1999. 2000H) [-01 implementation. Most names. Name. Pitch. Meshing pitch. Tooth pitch. Special ring crown. Dissipation length. Outer ring spacing. Report system conversion. Price
Light measurement length
Solution section quality public relations
Model limit La Zhong teaching Shang
Per meter standard
Effective name
Name Ai Suo
Ga Lun Jie Congee
Local section start
Ke to soft angle
Zhen section measurement length public welfare
Limit La Zhong hot recommendation
Every winter heavy fruit
JR.T9016.1-1999
1.3 Li Yin can mark the chain model mountain structure type code and pitch composition, structure The type code ML indicates the molded chain produced according to Table 1; ML indicates the molded chain produced according to Table 2: CL stamping chain marking example:
The molded chain with a nominal pitch of 0m adopts the specified values ​​in Table 1: ML.100JD/T906.1-1999
JB/T416.1-1999
The molded steel chain with a nominal pitch of 1D0mm adopts the specified values ​​in Table 2: M,100-JB/T 9016.1
The steel chain with a nominal pitch of 80mm adopts the specified values ​​in Table 2:
L80-JB/T 9016.1-1999
4 Technical requirements
4! The length of the chain link should be consistent with the direction of the steel fiber. 4.2 The surface of the chain parts shall not have cracks, marks, oxide scale and traces of material overheating. The chain parts shall not be repaired. 4.3 The assembled chain shall ensure that all joints can rotate flexibly. 4.4 The length of the chain assembly shall be determined by the manufacturer and the user. 5 Test methods and inspection rules
5.1 All chains shall be tested for the flexibility of the external and joint parts according to the requirements of 4.3 and 4.4. 5.2 From each batch of chains produced, select 3 chains with 5 sections and 1 chain with the specified length (then 5.5] to carry out the test. The 5-section chain segment H is required to check whether it meets the requirements of 3.2 (except the specified length of the chain); the specified length chain segment is used to check the average length tolerance L specified in the corresponding table. When the measurement result does not meet the requirements, a repeated test is carried out and the number of repeated test samples is doubled. The result of the repeated test is the final result.
5.3 The total length of the annual batch chain should not exceed 1000m. 5.4 The row spacing P is 0.01. 5.5 Take the chain segment with the specified length of 32mm or 500mm and measure it under the condition of full-length support and 0 .0" Measure its length under the state of ultimate control load.
5.6 All chain pieces are inspected periodically. 5.7 Use a material tensile testing machine to determine the ultimate tensile load of the chain. The test length is at least 4 pitches, and both ends are connected to the testing machine with pins. The chain must be able to rotate freely. If the breakage occurs near the clamp, the test can be repeated. 5.8 Determine the weight of each meter of the chain. Take one or several sections with a length of about 15m for testing. 59 When the structure, material or process of the chain is changed, the first batch of chains produced after the change should be type tested. The test content should include:
a) Measure the ultimate total difference of the standard length of the chain, and the sample number is 10 pieces randomly selected. b) Measure the light ultimate tensile load of the chain, and the sample number is randomly selected. Pieces. Stone marking, packaging and storage
6.! Each chain section should be marked with the chain model, standard number and manufacturing mark on at least one inner or outer ring. The chain should be packed in a closed box. Before packing, apply anti-rust grease: Use plastic film to wrap the chain. When the chain is shipped, the packaging box shall include the following contents: a) Product name and model: b) Factory number (or contract number: c) Box size and destination (port), manufacturer name and shipment date. 4 Products should be stored in a well-ventilated warehouse without corrosive gas without opening the package. 7.1 Under the conditions of following the storage, installation and use rules, the manufacturer shall ensure that the chain meets the requirements of the standard. 7.1 The warranty period of a group of chains is 18 months, but not more than 24 months from the date of shipment. During the warranty period, if the chain is damaged due to poor quality and cannot be used normally, the manufacturer shall repair or replace it for the user free of charge.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.