Some standard content:
ICS83.180
Applicance No.: 10945—2002
Chemical Industry Standard of the People's Republic of China
HG/T 3697—2002
Hot-melt adhesives for textiles
Hot-melt adhesives for textiles 20020928 Issued
2003-06-01 Implementation
Planned Issued by the State Economic and Trade Commission of the People's Republic of China Foreword
This standard is formulated based on the actual situation of China and the level of similar products in foreign countries. The appendix to this standard is a normative appendix.
This standard is issued by the former State Administration of Industry and Commerce of the People's Republic of China. This standard is under the jurisdiction of the National Adhesive Standardization Technical Committee HG/T3697
The sponsor of this standard is: the Nonwoven Professional Committee of the China Anti-woven Engineering Society, the Hot-melt Adhesive Branch. The main drafters of this standard are: Ye Shengrong, Pan Guodong, and Pang Anquan. This standard is under the jurisdiction of the Adhesive Standardization Technical Committee. 1 Scope
Hot melt adhesives for textiles
HG/T36872002
This standard specifies the specifications, models, technical requirements, test methods, and packaging, marking, transportation and storage of hot melt adhesives for textiles.
This standard applies to hot melt adhesives for textiles, including poly(ethylene glycol), poly(ethylene terephthalate), poly(ethylene glycol), poly(ethylene terephthalate), poly(ethylene vinyl alcohol), and poly(ethylene vinyl acetate). 2 Normative references
The clauses in the following documents become the applicable clauses through the application of this standard. For documents with a reference date of April 4, all subsequent amendments (excluding those in the past) or revisions are not applicable to this standard. However, parties who have reached an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced documents, the latest version applies to this standard. 116529 Standard atmospheres for conditioning and testing textiles GB/T1033-1986 Test method for density and density of plastics GB/T1636-1983 Test method for apparent density of molding compounds GH/T2916-1397 Plastics Polyethylene and copolymer resins - Sieve analysis by air spray apparatus GB/T 36A2-200 Determination of the flow rate and volume flow rate of thermoplastics GB/14503 Test method for melting point of some products Optical method 31984 GB/T528%1 Determination of water content in chemical products - ... 628
Determination of moisture content of chemical products GB/T6678
General rules for sampling of chemical products
GB/T 6879
General sampling plan for chemical products
T/T8629-1588 Washing procedure for textiles GB/T9343-1999 General determination method for plastics B/12006.2999 Determination of moisture content of deep-melted or filtered GH/12CV6,8-1339 Method for determination of amine content F7/T0107-2000 Preparation method for combined sample of heat-melted adhesive fabric for clothing FZ/TC10A2-2000
Determination of cavitation of heat-melted adhesive interlining for clothing FZ/TC183-2000
Outline specification for hot-melt adhesive interlining 3.1 Product classification
Hot melt adhesive products are classified into amines, esters, high density ethylene, low density ethylene, ethyl acetate and ethylene-ethylene copolymers.
3.2 Product marking and naming
3.2.1 Hot melt adhesive product labels include the categories of hot baking adhesives, melting bed speed, particle size range, screen melting range, and the like. The English letters and the effect group are missing. The first part of the product mark is the type of heat treatment agent, which is expressed in English letters. The second part is the speed of the body, which is expressed in English and Chinese numbers. The third part is the product type, which is expressed in English and Chinese numbers. The fourth part is the product type, which is expressed in numbers. The first and fourth parts are connected by a half-line (-). In addition to the product marks specified above, enterprises can also add marking codes according to their needs and place them on the product specifications page, connected by a dash (-).
3.2.2 Product naming can be the product use and hot melt adhesive category name (full name), or the whole hot melt adhesive category name (abbreviation)
3.3 Product marking code regulations
3.3.1 Hot melt adhesives are marked in English, and the code is shown in Table 1. Hot melt adhesive category marking code
Hot melt adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
High speed melting adhesive
Table 2 Grain width range national marking code
Grain density core by & logic
Two grain shape (potential control displacement)
2c)pm-.5cogm (general material except application)
mcm Material point net music
m--purple point total
Baking range The value is expressed by "digital representation of the benefit" 3.3.4
3.4 Product marking and part name example
Length 3 is the common expansion rate of the hot melt adhesive for the powder point. Table 3 Co-solvent hot melt adhesive for powder point
Product marking
HA c2G P,-123
Technical requirements
4.1 Appearance
Marking meaning
Risk 12>
Shock body certificate selling rate mi1
Other wind amine thermal adhesive
Color milky (light beautiful) powder or milky to fluorescent particles. 49
Marking code
Phase point use its shadow cool
Monitor thermal adhesive
Fruit bottom thermal cultivation area
4.2 Technical indicators
The technical indicators should meet the requirements of Table 1.|| tt||molten metal model
predicted body dynamic leakage rate, Juuin
contains density.%
release points: dead
connection degree rn
to the current government.g/nr
time technical washing
with dry cleaning·time
model position,
1 (for the melt flow rate has a standard value.
0.42--0.57
230--509
5 for the light order of the body requirements of the two parties and other; with this, 5 test methods
5. 1 Appearance
H Continent.
5.2 Flame melting range
According to B/T463% flow method.
5.3 Melt flow reversal rate
Table 4 Technical indicators
C.t5--C.6s
200--500
n.967.n.06:5. 14.a. n72
0. 39--0. 45
29~243
263--EX
200--500
HG/T36972002
5--y0n
200·-5no
5.3.1 Apply H/3433 medium heat rate plastic falling flow card test method, select the standard difficult oral inner diameter fire 2.095mm, test temperature and load as shown in the table, if the load is not 1.18N, then convert the measured value into Assume that the test temperature and load are the indicated values under 21.1 conditions, Table 5. Test conditions Assume that the test conditions are as follows 5.3.2 Calculation of melt flow rate (melt flow rate) by three-way equation [IDPE MFR = DX500 Falling body velocity, in grams per 10 minutes (/10): - Arithmetic mean of the mass of the cut specimens, in grams (g); (31) HG:T 3697--2002
Cut-off single
If the machine has only a white power supply device, it can also be placed (calculation: MER
Wu Zhong:
Melt flow rate, in grams per 10 minutes (/10in): Material diameter, in centimeters (c:
Hot melt adhesive refining forest sieve, in grams per square centimeter g/cm>; one live rod travel distance, in meters rm): one live rate and the time taken for the travel distance, the unit price is seconds (s). 5.4 Moisture content
5.4.1A method
The sample is anhydrous methanol GT1200%. 2 Flow extraction: The extracted water is then GBT3283 gram method, 5.4.2B method
According to B/6284 method. The density is 5--%, the pressure is less than kPa (2)
Note, according to the total system and the total moisture content, the routine long-term test is carried out according to H method, the protection test is carried out according to A method, and other hot-melt adhesives are carried out according to the long-term test method.
5.5 Ash content
5.5.1 For hot-melt adhesives, high-density ethylene, low-density polyethylene, ethylene acetate, ethylene-vinyl alcohol and other hot-melt adhesives, the temperature is 7C+50: 3/T9.15A. 5.5.2 For hot-melt adhesives, the temperature is 7C+50: 5.6 Density
According to GT 1031. 5.7 Apparent surface strength According to TSm standard. 5.8 Tensile strength According to GB/T2315 method. 5.B.2B method 5.8.2.1 Principle of the method Take a certain amount of sample and perform the test by machine separation method. 5.8.2.2 Sample preparation Take a sufficient amount of sample and divide it into four parts by the quartering method. Usually, take more than 25 samples each time. Unless otherwise agreed, the test shall be carried out on the sample when it is received and delivered. When the test cannot be carried out by the operator, the sample shall be placed in a closed container in order to prevent the sample from being electrostatically charged. Drying delay, at the beginning of the test, can add the sample amount (.1 head of aluminum oxide as antistatic agent. Cobalt chloride is in powder form, with a particle size less than 3t, 5.E.2.3 only
a dismantling belt machine: double action times 3g drink/min. Motion center 12mm. Vibration times 175 times/min about · according to the width height mr.~3m adjustable, machine speed 2ur/in.
sieve: straight grid center\ height r: the gold Guorun medical and time. Should be root period inspection happy and type mixing grid small people have choice.
note, can be indicated to add other disinfection flow, such as 1. "Check the product will be in the standard agent 2·-4d, take out the temporary dry can be used, desktop large end. 1.
dAnalyzer, feel through u.1ng.
eTimer or stopwatch.
5.8.2.4Operation method
HG/T36972002
On a transparent paper, weigh 25 grams of resin, add antistatic agent including aluminum hydride C.0258 and mix. Gently put the mixed resin into the sieve, firmly install it on the vibrating sand screener, start the sieve machine, start the timing at 12:00, and remove the sieve together with the sieve bottom after 20 minutes. Store the sieve contents of each sieve in a container of known mass in the case car, and weigh them on the 103 floor. 5.8.2.5 The percentage of the residue on sieve R (%) is calculated according to the formula (3): R = type × 100
W\ - mass of the sample, in grams (g) w - mass of the residue on sieve. The unit is grams (g). The arithmetic mean of the two determinations is rounded to one decimal place. 5.8.2.6 The same sample is measured twice. When the residue on sieve percentage is equal to or greater than 5%, the difference between the two determinations should not be less than 2%. When the residue on sieve percentage is less than 5%, the difference between the two determinations should not be less than 1: the test sample should be tested. The test dummy should be used. 5.9 Water resistance
5.9.1 The method for making the sieve retention is shown in the table. 5.9.2 The method for selecting the sieve retention in accordance with 2ZC1281 is as follows: 5.10 Dry cleaning resistance
5.10.1 The dyeing layer group will meet the requirements of the preparation of the sample A. 5.10.2 The resistance to hot washing under the F/T8 method is implemented.
6 Inspection rules
6.1 Inspection classification
6.1.1 Factory inspection
Products must be inspected according to the following items before leaving the factory: Each batch of products must be inspected by the technical inspection department of the manufacturer before leaving the factory. The manufacturer must ensure that each batch of products leaving the factory meets the quality standards and is accompanied by a production certificate. 6.1.2 Type inspection
Products are inspected for all technical requirements, which is called type inspection. It is carried out in the following situations: Type inspection, trial production and adjustment of new products and old products transferred to the factory for production. When the material, formulation and processing have major changes that may affect the product performance, the normal production shall be stopped once every 1 to 2 years: when the production is stopped for more than half a year, the quality supervision department shall make the inspection according to the inspection results. 6.2 Inspection items 6.2.1 Factory inspection Factory inspection items include: Appearance: Melt flow rate. Melt flow rate. HG/T3697—2002. 6.2.2 Type inspection Type inspection items include: Appearance: Melt flow rate. Moisture content. Density.
Packing density,
R shoe degree.
5 Natural division-
Resistant flow.
i Attached washing.
6.3 Sampling and batching
6. 3. 1 Sampling
The sampling unit source shall be in accordance with the provisions of (B/T6678 Table 2. When the number of units of the overall material is greater than 500, the number of sampling units shall be calculated by the triple of the cube root of the number of units of the overall number, that is, 3×NN is the number of units of the overall number). If there is a decimal, it shall be rounded up. The sampling lamp shall adopt the provisions of (GB/T6679. Place the sample bag in a flat position, insert the sampler diagonally from one side of the bag mouth to three-quarters of the diagonal to take the sample. Each batch of sampling shall not be less than 1.0kg per day. The selected test standard sentences shall be divided into two clean packs, and the sealed ones shall be dialed The bottle shall be marked with the model, specification, date of receipt, etc. and submitted to the inspection department for inspection and kept for inspection for thirteen days. 6.3.2 Group batches
The products produced within 24 hours or each batch produced within 24 hours is called a batch. The same type of products can also be mixed together as a batch. The mixed batch must meet the requirements of the standard. 6.4 Acceptance
The user has the right to accept the product according to the technical standards. If there is any problem, the manufacturer shall conduct inspection within six months before the product is shipped. If any item does not meet the standard, the manufacturer shall conduct inspection within six months before the product is shipped. When required, samples should be taken from the packaging units within the same tray for re-testing. If the re-testing results still do not meet the requirements, the batch of products shall be deemed unqualified. When the supply and demand parties have different opinions on the product quantity, the sample structure can be selected through consultation between the two parties. The sample structure shall be selected in accordance with the standard.
7 Packaging, marking, transportation and storage
7.1 Packaging
Thermoplastic woven packaging or kraft paper packaging is used for this purpose. Each package is accompanied by a product inspection certificate: 7.2 Marking
Super adhesive The product package should have the following information: product name, model, mark, implementation standard, if there is a trademark, the name, address, batch or period of the production unit, etc. d Quality mark: 7.3 Transportation HGT3697-2002 Hot melt adhesive is a non-hazardous device. Handle with care during transportation. Iron hooks are prohibited when loading eggs to protect the eggs from being exposed to the sun, rain, heat, or re-pressing. 7. 4 Storage
The product must be stored in a shaded, ventilated, dry place, avoid sunlight, rain and high temperature. The shelf life is one year from the month of production. After the storage, the product can be used after the test and withdrawal of the items specified in this standard. When storing hot-explosive adhesive products in the warehouse, the relevant provisions of the warehouse fire prevention and safety management regulations of the Ministry of Public Security shall be followed. HG/T3697—2002
A.1 Principle
Appendix A
[Normative Appendix]
Coating group including test sample preparation method
Put the hot melt adhesive in a suitable coating machine (such as dot coating, powder coating or hot block transfer), and heat it to make a cloth after cooling. The hot melt adhesive cloth has a hot melt adhesive surface, and the hot melt adhesive is placed in a hot press under certain temperature, power and time conditions to make the hot melt adhesive bond with the material: A.2 Equipment and use
A, 2.1 Coating machine: for dry clothing fabrics, it can be a powder coating machine such as powder coating or hot melt transfer, 4.2.2 The hot press shall comply with the provisions of FZ/T01u76-20001+±.1. 4.3 Standard village applicable fabric provisions
Standard batch fabric specifications See Table 1
Table A. 1Standard bottom weaving suppression regulations
Standard bottom sealing number
Technical requirements
Think about the rubber phase measurement
Floating accounted for half continuous cotton
23.8/2r.at21×21)
256x228(60x58)
1357353
21X2/28(2/2:21*
165 165(42:22)
T/C65/S5)
21×/29(28*/5x:21*
105X37(42X2)
18:1N32*X32
:53X37(33X22)
A.4Standard fabric regulations
Under aging
Equal to the regulations of F2/711076-20U0 No. 5.2.5Standard road extension quantity regulations
Standard coating most difficult media see table 2.
GB:T $629:A
Water washing only cavitation
(not less than)
F7/T01082
Ten heat changes
(not less than ten total
falling to
-2. U-1.5
Virtual combination:
GL cotton wood color
H/T335<fine core polyester cotton low material
Original cloth: 4n/5526 fine Lai
Painted mixed fine printed cloth
[170136 and other accompanying bodies, cotton but medicine
Original color cloth 2.
Dazzling glue
Eirspe
A,6 Selection of delamination processing method
Selection of coating processing method see Table A.3.
Standard delamination amount of steam
Table: 3 Selection of coating processing methodbzxz.net
Hot-stuck glue agent lifting range
,em~.zon um
2C M--500
A.7 Two aspects of the test specimen
A.7.1 Cut the test specimen from 1m away from the cloth and 10cm away from the edge. The adopted method must be HG/T3697--2002
.7.1 The test specimen shall not have any stains, color reduction, creases, missing stitches, or base fabric not hooked, which may affect the quality of the test specimen. A.8 Preparation of the test specimens
According to 2/T01676 above
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.