Some standard content:
Chemical Industry Standard of the People's Republic of China
HG / T 2814 1996
General-purpose polyester polyurethane adhesive
Published on 1996-06-28
Ministry of Chemical Industry of the People's Republic of China
Implementation on 1997-01-01
HG/T2814-1996
This standard is formulated based on the actual situation in my country, which provides unified technical requirements for general-purpose polyester urethane adhesives in my country's chemical industry.
This standard only stipulates general-purpose polyester urethane type I adhesives. Currently, general-purpose polyester urethane type I adhesives include 101 adhesives and other adhesives
Appendix A of this standard is a prompt appendix.
This standard is proposed by the Technical Supervision Department of the Ministry of Chemical Industry of the People's Republic of China and is under the jurisdiction of Shanghai Rubber Products Research Institute. This standard was drafted by Shanghai Xinguang Chemical Factory. The main drafters of this standard are: Lu Dongzhen, Nang Wanxing, Xiao Baoqin, Wu Guanyun, Xie Yishua. This standard is entrusted to the National Adhesive Standardization Technical Committee for interpretation. Scope
Chemical Industry Standard of the People's Republic of China
General-purpose polyester polyurethane adhesive
HG / T 2814 — 1996
This standard specifies the technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of general-purpose polyurethane I avoidance adhesives.
This standard is applicable to room temperature curing reverse-type ester polyurethane I type adhesives prepared from components A and B. 2 Referenced standardswww.bzxz.net
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are all valid. All standards are subject to revision. Parties using this standard should explore the possibility of using the latest versions of the following standards: GB/T 601-88 Preparation of standard solutions for titration analysis (volumetric analysis) of chemical reagents GB/T603--88 Preparation of preparations and products used in test methods for chemical reagents (nc9ISO6353/1:1982) GB/T 1723--93 Method for determination of viscosity of coatings
GB/T2793-1995 Method for determination of non-volatile matter content of adhesives GB/T2794-1995 Method for determination of viscosity of adhesives GB/T2944--82 Provisions for packaging, marking, transportation and storage of adhesive products GB/T6680--86 General rules for sampling of liquid chemical products GB/T7124-86 Method for determination of tensile shear strength of adhesives (metal to metal) 3 Requirements
The product shall comply with the technical requirements in Table 1
Table 1 Technical Requirements
Non-volatile matter content. %
Method A, Pa·_
Method B.
Isocyanate content. %
Shear strength, MPa
Component A
Colorless or light yellow semi-transparent viscous liquid
0. 15~0, 35
Approved by the Ministry of Chemical Industry of the People's Republic of China on 1996-06-289. 0
Component B
Colorless or light yellow transparent viscous liquid
58 ~62
11~ 13
Implemented on 1997-01-01
Test method
HG / T 2814 - 1996
Standard solutions, preparations and products required in the test. Unless otherwise specified, the preparation shall be in accordance with the provisions of GB/T601 and GB/T603. 4.1. Determination of appearance. 4.2. Determination of non-volatile content. According to the provisions of GB/T2793, the test temperature of amino adhesive is 105°C. 4.3. Determination of viscosity. 4.3.1. Method A. According to the provisions of Method A-rotational viscometer method in GB/T 2794. The rotor is No. 1 rotor, and the speed is 12r/min. 4.3.2. Method B. According to Method Z in GB/T 1723. 4.4. Determination of isomucic acid content. 4.4.1. Reagents and solutions. According to the provisions of Tu-4 viscometer method 1.
4. 4. 1. 1 Toluene-dibutylamine
1mol/L
4. 4. 1.2 Hydrochloric acid 0.5 mol)/L
4. 4. 1. 3 Isopropyl alcohol
4.4.1.4 Bromocresol green indicator
4. 4.2 Determination steps
4.4.2.1 Weigh 1.5~2 g of the sample (accurate to 0.0002 g) and pour them into a 250 mL iodine volumetric flask. Transfer 20 mL of toluene-dibutylamine solution into the iodine volumetric flask, shake well and place at room temperature for 20 min. Seal the flask with a small amount of isopropyl alcohol, dilute with 50 L isopropyl alcohol, add 3~4 drops of bromocresol green indicator, and titrate with 0.5 mol/L hydrochloric acid standard solution until it turns yellow. Perform a blank test in the same way. 4, 4, 2, 2. Perform a second determination. If the difference between the percentages of the second determination exceeds 0.5%, the determination must be repeated. 4. 4.3 Calculation and expression of results.
The mass percentage X (%) of isocyanate is calculated according to formula (1): Xe
c(V, - Y,)× 0.042
Wherein: c—mol concentration of hydrochloric acid, mol/L; V
—volume of hydrochloric acid consumed in air titration, mL; volume of hydrochloric acid consumed in sample titration, ⅡL
× 100
The mass of isocyanate expressed in grams equivalent to 1.00mL of hot acid standard titration solution [c(HC1)=1.000mol]/L]:
Sample mass, g.
Take the average of the two measured values as the result. 4.5 Determination of shear strength
Perform according to GB/T 7124
4.5.1 Preparation of test specimens
Perform according to the product manual. If there are no specific regulations, it is recommended to proceed according to the following method. 4.5.1.1 Test piece
LY12-CZ aluminum alloy test piece,
HG/T 2814—1996
The surface of the test piece is cleaned with detergent, degreased with solvents such as acetone, ethyl acetate, gasoline, etc., polished and wiped with O# sandpaper, and then treated with chemical methods. The treatment formula is as follows: mass ratio
Sodium dichromate (sodium dichromate)
Concentrated sulfuric acid
4. 5. 1. 2 Glue coating
First, mix components A and B, add 5 parts of component A and 1 part of component B by mass, apply glue on the test piece, let it cool for 20 to 30 minutes, apply twice in total, and then overlap the test pieces. Each batch of glue should be coated with 5 pairs of test pieces. 4. 5. 1.3 Curing
Place the test piece on the fixture, apply a pressure of 50kPa, and heat it in a constant temperature drying oven to 100±2℃ and keep it for 4h. Then naturally cool.
5 Inspection rules
5.1: Product sampling
Perform according to GB/T6680
5. 2 Inspection classification
5.2. 1 Factory inspection
5.2.1. 1 Factory inspection items are all items listed in Table 1, and the viscosity can be determined by either method A or method B. 52.1.2 If one of the product test results is unqualified, double samples of the batch should be drawn to retest the unqualified items. If there is still one unqualified result, the batch of products is unqualified. 5. 2.2 Type inspection
The items of type inspection are the same as those of factory inspection. Among them, the viscosity determination uses method A. 6 Marking, packaging, transportation and storage
61 Packaging, marking, transportation
According to the provisions of GB2944
This product should be stored in a cool and dry environment. The storage period of group A is one year, and the storage period of group B is half a year. Appendix A (suggested appendix)
Precautions
A. 1'Components A and B can be used after mixing. The more component B, the higher the temperature and the faster the curing. Therefore, the amount of glue should be strictly controlled. It should not be too much to avoid waste caused by failure. A, 2 The small amount of isocyanate contained in component B is a toxic substance. Its vapor escape will irritate the eyes and respiratory tract, and seriously cause tears and coughing. Therefore, it is necessary to strengthen good ventilation and exhaust in the workplace, pay attention to labor protection, A. 3 This product contains a large amount of organic solvents. Avoid contact with extreme temperatures and open flames when using it. Pay attention to ventilation.
Chemical Industry Standard of the People's Republic of China
General-purpose polyester urethane adhesive
HG / T 2814 ~ 1996
Editor Chemical Industry Standard Editing and Publishing Group
(Standardization Research Institute of the Ministry of Chemical Industry)
Postal Code: 100011
Printing Chemical Industry Standardization Research Institute
Copyright reserved. No reproduction allowed
Format 880×12301/16 Number of printed sheets 8000 First edition in October 1996
First printing in October 1996
Number of prints 1-300
Cost 4.70 Yuan
y0o1 918c
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.