This standard specifies the product classification, requirements, test methods, inspection rules, marking, packaging, transportation and storage of multi-purpose axes. This standard applies to multi-purpose axes. QB/T 2565.6-2002 Steel Axe Multi-purpose Axe QB/T2565.6-2002 Standard download decompression password: www.bzxz.net

ICS 25.140.30
Classification number: J47
Registration number: 10872-2002
Light Industry Standard of the People's Republic of China
QB/T2565.6--2002
Generation QB/T3857.8: 1999
Multi-purpose axe
AxesMnltiuse axes
2002-09-21 Issued
The State Economic and Trade Commission of the People's Republic of China Implemented on December 1, 2002
QB/T2565.6-2002
This standard is a revision of the original national standard B8389.9-1987 (the standard was converted into the national standard number Q3857.81999 in 1999, and remains unchanged). The contents are as follows. · Added the example of the mark of the production ratio (see 3,3). - Some necessary adjustments have been made: This standard contains the following information:
This standard is issued by the National Center for the Promotion of International Trade in Hardware and Tools. This standard is the following information: The Municipal Industry Research Institute is responsible for drafting this standard. From the date of implementation, this standard shall be in addition to the light industry standard QB3857.8-1999 or QB/T2565.6-2002 issued by the National Light Industry Commission at the same time. Scope This standard specifies the product classification, requirements, test methods, inspection rules, marking, packaging, transportation and storage of multi-purpose steel stools. This standard applies to the following multi-purpose products. 2 Normative references The following documents shall become the terms of this standard through the application of the technical standard. The referenced documents shall be marked with the date of reference, and all subsequent modifications (including amendments) shall be included in the referenced documents. None of the above versions are applicable to the second-generation standard, however, the new versions of these documents may be used if the agreement is reached based on this standard. For any referenced parts that are not in the same version, the original version shall apply to this standard. GD.T8289--2003 General technical conditions for steel production QB565.1-2002 Specifications for carbon steel products GB/T1298 Technical conditions for carbon steel products GB/T1941 Test method for wood hardness 3 Product classification The stripping type of the same type is shown in Figure 1, and the shapes of the joint heads are Type A and Type B. VZEZ
Figure 1 is used as an example
3.2 Basic dimensionsWww.bzxZ.net
It is used as the basic dimension element [specification 1
3.3 Marking example
Basic designation
Table 1 Basic dimensions of multi-purpose products
Basic designation
Product marking consists of product name, specification, model code and standard number. Specification: The multi-purpose product with a maximum size of 260A should be marked as: $26AQB/T2565.6-2002
4 Requirements
4.1 Hardness of the steel bar should be 46~52HRC, and the hardness of the groove and pull-out part should be 42~50HRC. 4.2 Assembly
The steel bar of the multi-purpose product should be tightly matched with the body, and there should be no obvious separation. 4.3 Performance
During the operation, no cracks or defects will occur. 4.4 Other requirements
The requirements shall be in accordance with the provisions of 0B8389-2003 Section 3. 5 Test methods
5.1 Performance test
5.1.1 After the T10 steel 10 specified in GB/T1298 is used, the head should not show cracks, damage, etc.: The test piece used for the test shall be 20mm in diameter and 250~300HB in hardness. 6.1.2 According to the provisions of Table 2, 3 balls are driven into the wood with a strength of not less than 64MP, and the falling part is fixed with a nail. The balls are continuously pulled out from the wood. After the test, the falling part is not damaged. 5.1.3 The materials used for the test shall be inspected in accordance with the provisions of GB/11941. Table 2 Specifications for the sniffer test
TKAONY KAa-
Nail penetration depth
QB/T 2565.6·2002
5.2 Other test methods
Other test methods for multi-purpose products shall be in accordance with the provisions of Section 4 to 6 of GB/TB389-203. In addition to the provisions of Section 5 of GB/TB389-203, the inspection rules for multi-purpose products shall also meet the requirements of Table 3. Table 3 Non-conforming categories, inspection items, quality levels and inspection levels Non-conforming categories
Marking, packaging, transportation. Storage
Test items
Assessment quality requirements (AQL)
Standardized markings, packaging, transportation, storage shall comply with Section 6 of GB8389-2003. 3
Inspection (
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.