JB/T 10237—2001 This standard specifies the vibration (acceleration) technical conditions for finished tapered roller bearings with nominal inner diameters of 15 to 60 mm and 30200, 32200, 30300 and 32300 series in GB/T 297 "Rolling bearings tapered roller bearings dimensions". This standard specifies that vibration (acceleration) group Z is the basic requirement for grade 0 bearings and is applicable to production inspections by bearing manufacturers; groups Z1 and Z2 are applicable to bearings for which users require control of vibration (acceleration) levels. For manufacturer inspection and user acceptance. This standard was first issued in May 2001. JB/T 10237-2001 Rolling bearings tapered roller bearings vibration (acceleration) technical conditions JB/T10237-2001 Standard download decompression password: www.bzxz.net

S21.100.20
Machinery Industry Standard of the People's Republic of China
JB/T 10237-2001
Rolling bearingsSpecifications of vibration(acceleration)fortaperedrollerbearings
Published on 2001-05-23
Published by China Machinery Industry Federation
Implemented on 2001-10-01
JB/T102372001
This standard is the first time to be drafted. This standard is proposed and managed by the National Technical Committee for Standardization of Rolling Bearings. The drafting units of this standard are: Geyang Bearing Research Institute, Luyang Bearing Group Co., Ltd. The main drafters of this standard are: Ren Hongwei, Chen Zhujian, Peng Lan. ■Scope
Standards of the Machinery Industry of the People's Republic of China
Rolling bearingsTapered roller bearings
Vibration (acceleration) technical conditions
Rnlling hearingsSpecifications of.vibratioa(aeceleratlon)for tarered roller bearings
JB/T10237-2001
This standard specifies the vibration (acceleration) technical properties of finished roller bearings with a nominal inner diameter of 15~60mm and an overall dimension conforming to the 30200, 32200, 30300 and 32300 series in GB/T297. The vibration (acceleration) group 2 specified in this standard is the installation requirement for D-grade bearings and is applicable to the production inspection of bearing manufacturers. The second group is applicable to bearings that are customized by users with certain vibration (shearing speed) level requirements for manufacturer inspection and user acceptance. 7 Reference standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. At the time of publication of this standard, all the versions shown are valid for: All standards will be subject to revision. Parties using this standard may consider the possibility of using the latest versions of the following standards. GB/1 247--1994
GBT2828-1981
JB/T 5314--1991
3 Definitions and units
Rolling shaft roundness and outer dimensions
Batch inspection counting sampling procedures and sample tables (applicable to the inspection of consecutive batches) Rolling bearing vibration (acceleration) measurement method This standard adopts the definitions and units given in JB/T5314. 4 Technical requirements
The vibration acceleration level of a single bearing shall not exceed the provisions of the table! China Federation of Machinery Industry Approved on 201-05-23 2001-10-0L actual box
bearing nominal inner diameter 2
1) is expressed in the bearing code,
measurement method
JB/10237-2001 bzxz.net
3020, 32200 series
the basic vibration core acceleration level of the suction solution is not more than 15 Product 5.1 The axial load applied to the tested bearing shall comply with the provisions of Table 2. Table 2
Bearing nominal internal weight
1 Including 15mm%
303, 323
Avoid applied radiation
Other requirements for the bearing vibration (acceleration) measurement method are in accordance with the provisions of IB/T5314, 5.3
6 Inspection rules
6.I When the vibration (acceleration) level of a single bearing exceeds the level specified in Table 1, the bearing is considered unqualified. dR
6.1 When sampling and inspecting a batch of bearings for vibration (acceleration), follow GB/T2829, use the general inspection level II, adopt the stop band noise one-time sampling plan, and the qualified level AQL value is 2.5,
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.