title>GB 2099.3-1997 Plugs and sockets for household and similar purposes Part 2: Particular requirements for converters - GB 2099.3-1997 - Chinese standardNet - bzxz.net
Home > GB > GB 2099.3-1997 Plugs and sockets for household and similar purposes Part 2: Particular requirements for converters
GB 2099.3-1997 Plugs and sockets for household and similar purposes Part 2: Particular requirements for converters

Basic Information

Standard ID: GB 2099.3-1997

Standard Name: Plugs and sockets for household and similar purposes Part 2: Particular requirements for converters

Chinese Name: 家用和类似用途插头插座 第二部分:转换器的特殊要求

Standard category:National Standard (GB)

state:in force

Date of Release1997-01-02

Date of Implementation:1999-05-01

standard classification number

Standard ICS number:Electrical Engineering>>Electrical Devices>>29.120.30 Plugs, sockets and connectors

Standard Classification Number:Electrical Engineering>>Electrical Equipment and Apparatus>>K65 Other Electrical Apparatus

associated standards

alternative situation:Replaced by GB 2099.3-2008

Procurement status:IDT IEC 884-2-5:1995

Publication information

publishing house:China Standards Press

ISBN:155066.1-14905

Publication date:2004-07-22

other information

Release date:1997-12-30

Review date:2004-10-14

Drafting unit:Guangzhou Electrical Science Research Institute, Ministry of Machinery

Focal point unit:National Technical Committee for Standardization of Electrical Accessories

Publishing department:State Bureau of Technical Supervision

competent authority:China Electrical Equipment Industry Association

Introduction to standards:

This standard is only applicable to converters with alternating current, with or without protective doors, with or without fuses. The fuses mentioned in this standard are not fuses used as overload protection for appliances or parts of appliances. GB 2099.3-1997 Plugs and sockets for household and similar purposes Part 2: Special requirements for converters GB2099.3-1997 Standard download decompression password: www.bzxz.net

Some standard content:

GB 2099.3---1997
This standard adopts IEC884-2-5:1995 (first edition) & Plugs and sockets for household and similar purposes Part 2: Special requirements for converters
Converters are related products of plugs and sockets for household and similar purposes, including: converters with fuses, multi-bit converters, type converters, intermediate converters, etc. They have many categories, a wide range of uses, and certain particularities. Therefore, we adopt: C884-2-3:1995 & Plugs and sockets for household and similar purposes Part 2: Special requirements for converters" to formulate this standard. This standard should be used in conjunction with (B2099.1-1996 "Household and similar plugs and sockets Part 1: General requirements". This standard applies to various converters for household and similar purposes. This standard supplements the content of (IEC:884-1) that was deleted in GB2099.1 but applies to special requirements of converters. After the promulgation and implementation of this standard, the assessment of converters for household and similar purposes should be based on this standard. This standard is proposed by the Ministry of Machinery Industry of the People's Republic of China. This standard is under the jurisdiction of the National Technical Committee for Standardization of Electrical Accessories. The drafting units of this standard are: Guangzhou Electrical Science Research Institute of the Ministry of Machinery, Hangzhou Hongyan Electric Company, Beijing Stone Matsushita Electric Co., Ltd., Shenzhen Clever Electronics Co., Ltd., and Beijing Breakthrough New Technology Development Center. The main drafters of this standard are: Luo Huaiping, Yang Guoxian, Che Ning, Zhang Jie, and Lin Haiqing. This standard is entrusted to the Jinguo Electrical Accessories Standardization Technical Committee for interpretation. GB 2099. 3—1997
IEC Preface
1) IEC (International Electrotechnical Commission) is a worldwide standardization organization composed of national electrotechnical committees (IEC National Committees). The mission of IEC is to promote international cooperation on various standardization issues in the field of electrotechnical engineering. To this end, in addition to organizing other activities, it also publishes various international standards. The IEC international standards are entrusted to technical committees for formulation. Any IEC National Committee interested in the issue under discussion can participate in this formulation work. International organizations, governmental organizations and non-governmental organizations that have established relations with IEC can also participate in this formulation work. 1IEC cooperates closely with the International Organization for Standardization (ISO) under the conditions stipulated in the agreement it has reached with it. 2) Formal resolutions or agreements of IFC on technical issues are formulated by technical committees represented by national committees that are particularly interested in the issue, and express the international consensus on the issue as accurately as possible. 3) These resolutions or agreements are published in the form of standards, technical reports or guidelines, and are recommended for international use and accepted by national committees in this sense.
4) In order to promote international uniformity, IEC National Committees undertake to adopt EC International Standards as faithfully as possible in their national or regional standards. Any inconsistencies between IEC standards and corresponding national or regional standards should be clearly pointed out in the national or regional standards as far as possible.
5) IEC provides recognized non-marking procedures, but is not responsible for the verification of equipment that is not in compliance with its standards. International Standard IEC884-2-5 was prepared by SC23H: Plugs, Sockets and Switches, Technical Committee SC23: Electrical Accessories, IEC TC23. This publication is based on the following documents:
Draft International Standard Documents
23B/425/DIS
Voting Report
23B/454/RVE
Detailed information on the voting for this standard can be found in the voting report in the above table. This Part 2 standard should be used in conjunction with IEC Publication 884-1:1994 (Second Edition) Plugs and socket-outlets for household and similar purposes Part 1: General requirements. This standard lists the changes necessary to convert IEC Publication 8841 into an ILC standard; Particular requirements for adaptors.
Where Part 1 applies, it is only where it contains requirements related to adaptors. This standard uses the following typographical format:
-Requirements in the text: in roman font, test instructions: in italics;
Notes: in smaller roman font. 1 Scope
National Standard of the People's Republic of China
Plugs and sncket-outlets Forhousehold and simtar purposes-Part 2: Particular requirements for adaptors
Chapter 1 of GB 2099-1—1996 applies with the following changes. Add the following after line II:
tB 2099. 3-1997
id IEC 884-2-5:1995
This standard applies only to converters with or without protection doors, with or without fuses, for AC power. The fuses mentioned in this standard are not fuses used for overload protection of the converter or parts of the appliance. Add:
Note: Converters without protection doors are not used in the following countries: Italy (IT), Switzerland (VO). 2 Reference standards Chapter 2 of GB 2099.1-1996 shall apply after the following changes. The following content shall be added after Chapter 2: IFC 83 Plugs and sockets for household and similar general purposes IEC 269 Low-voltage fuses TEC 669-2-1:1994 Switches for household and similar fixed electrical installations Part 2: Particular requirements Section 1, Electrical switches 3 Definitions Chapter 3 of GB 2099.1-1996 shall apply after the following changes Note 3 is changed to: 3 “Electrical accessories” is a general term, including plugs, sockets and converters, while *mobile electrical accessories\ include plugs, mobile sockets and converters. The following content is added Note 5: 5 The term “converter” is a general term, including all types of converters, except for the special types mentioned in the specific reference. 3.25 is changed to:
Rated voltage
refers to the voltage specified by the manufacturer for the electrical accessory. If there is a corresponding standard, it refers to the voltage specified in the index. 3.26 is changed to:
Rated current
refers to the current specified by the manufacturer for the electrical accessory. If there is a corresponding standard, it refers to the current specified in the standard. Add the following definition:
3.101 Adaptor
Approved by the State Administration of Technical Supervision on December 30, 1997, and implemented on May 1, 1999
GB 2099.3—1997
A mobile electrical accessory consisting of a plug part and one or more socket parts as an integral unit. 3.102 Fused adaptor refers to an adaptor with replaceable fuses installed in one or more current-carrying poles. 3.103 A polarizcluscd adapter with fuses is a converter that is designed to maintain the correct relationship between the neutral and phase conductors when plugged into a socket installed in a polarized wiring device.
3.104 A multiway adapter is a converter that allows more than one plug to be plugged into the socket at the same time. 3.105 A conversion adapter is a converter that allows one or more types of plugs to be connected to a socket that is not designed to accept these plugs. 3.106 An intermediate adapter is a converter that allows one or more types of plugs to be connected to a socket through a control device such as a dimmer switch, timer switch, photoelectric switch, etc. The intermediate adapter can be an integral intermediate adapter or a converter connected by a flexible cord, the latter of which can be rewirable or non-rewirable.
Note: The control device itself meets the corresponding standards. For example, the electronic switch should comply with IEC669-2-1. 3.17 Rewirable intermediate adapter A converter with a replaceable cord or soft wire structure. 3.108 Non-rewireable intermediate adapter A converter that is assembled into an integral structure by connecting the converter and the soft wire or soft relay by the manufacturer. 3.109 External cable externalceahle The flexible cable of the external part of the intermediate converter. It may be a power cable or a flexible cable connecting the separated parts of the equipment. 4 General requirements
Chapter 4 of GB 2099.1-1996 applies. 5 General instructions on testing
Chapter 5 of GB 2099. 1-1996 applies. 6 Rated values
Chapter 6 of GB 2099. 1-1996 applies with the following changes. Add the following content:
6.101 The rated current of the converter shall not be lower than the rated value of the corresponding socket to which it is connected. 6.102 The rated current of the converter shall be the lower of the following two:
The sum of the rated currents of all plugs plugged into the converter. 6.103 The minimum rated value of the converter with fuse shall be equal to the rated value marked on the fuse. 6.104 The rated current of each socket part of the conversion group shall be equal to or greater than the maximum rated current of any plug into which the converter is inserted. 6.105 The rated current of the intermediate converter with an integral control device shall be equal to the rated current of the control device, or equal to the rated current of the socket where the controller is installed. It shall be the lower of the two. Whether it complies with the requirements of 6.101--6.104 shall be checked by observation. 7 Classification
Subsection 7 of GB 2099.1-1996 shall apply. 8 Marking
GB 2099.3—1997
(FB 2099.1—1996) Chapter 8 shall apply with the following changes. 8.1 The first knockout number (——) shall be replaced with: Rated current (A) and/or power (W)
Add the following at the end:
Use the word MAX (or maximum) to fully identify the rated current and/or power. Note 3. Examples of these markings are as follows: 1
MAX 2000W-MAX 10A, or
2000W-10A MAX, or
MAX10A,
10AMAX
(where \MAX\ can be represented by the Chinese character "最大\) Note 1: The power should be calculated using the nominal voltage of the power supply. After the last plug is connected, the maximum allowable power mark should be clear and easy to identify, and the mark on the multi-position converter cannot be marked on the plug-in surface of the socket.
The converter with fuse should have a mark indicating that the converter is equipped with a fuse. This mark can be shown by a symbol. The inter-leaf converter with fuse that can be rewirable should have a mark indicating the rated current of its fuse. This mark can be marked on the intermediate converter or on the attached label. The converter with fuse that cannot be rewirable should be marked with the rated current of the fuse specified by the manufacturer, which is suitable for the attached soft cord and related appliances.
8.2 Added:
Fuse
9 Size inspection
GB 2099. Chapter 9 of GB 11996 shall apply with the following changes. 9.1 The second paragraph shall be changed to:
The plug part of the converter shall comply with the requirements of GB 1002. 9.2 The second (—) shall be changed to:
The plug shall not be able to be mated with a socket with a different number of poles. Plugs specially manufactured to be mated with plugs with fewer poles shall be excluded, but shall not cause any danger (for example, the connection between the live pole and the grounding contact or the grounding circuit shall not be disconnected). 9.3 Added:
It is allowed that the size and type of the socket in the converter may be different from the system type specified in the national standard, but the different size and type must be technologically advanced and not affect the function and safety of the electrical accessories that meet the requirements of the national standard, especially the requirements of interchangeability and non-interchangeability. In addition, these electrical accessories of different sizes must also meet the other applicable requirements of this standard. Note: The plug part of the converter shall be able to meet the requirements of the plug mating recommended by the corresponding foreign and regional standards: 10 Protection against electric shock
GB 2099. 1--1996 Chapter 10 is applicable after the following changes. The second paragraph of 10.1 is as follows:
System instructions
I) In (GB 2099. 1-1996, 9.3 is deleted. In this standard, the content of 9.3 is supplemented as follows: GB 2099. 3-1997
When the plug of the converter is partially or completely engaged with the socket of the same system, the live parts of the plug part of the converter should be difficult to touch.
The sixth paragraph is changed to:
For the converter, the test finger is applied to each possible position when the converter is partially or completely engaged with the socket of the same system. Add the following content:
10.101 Unless the converter with fuse is completely removed from the socket or is designed to prevent accidental contact between people and live parts when replacing the fuse, it should not be possible to remove or replace the fuse in the converter. Whether it is qualified, observe and check through the traces.
10.3 The first paragraph is changed to:
When any other current-carrying pin is in the "touchable state", it should not be possible to make the pin of the relevant plug and the live socket of the converter or the pin of the converter and the live socket of the socket of the same system. 10.4 The inner part of the paragraph is changed to:
The external parts of the converter should be made of insulating materials, except for assembly screws, current-carrying and grounding pins, grounding strips and gold rings around the pins.
10.5 The first paragraph is changed to:
The socket part of the converter with a protective door should also be designed so that when it is not connected with the plug, the probe shown in Figure 4 cannot touch the live parts as much as possible.
11 Grounding measures
Chapter 11 of GB 2099. 1-1996 applies. 12 Terminals
Chapter 12 of GB2099.1-1996 shall apply with the following changes. The second paragraph of 12.1.1 shall be changed to:
Removable wireable intermediate converters shall have screw clamping terminals. 13 Structure of fixed sockets
Chapter 13 of GB 2099.1-1996 shall not apply. 14 Structure of plugs and mobile sockets
Chapter 14 of GB2099.1-1996 shall apply with the following changes. The title is changed to:
Structure of mobile electrical accessories
14.1 is changed to:
Non-detachable intermediate converters should be able to ensure that the flexible cable or cord cannot be removed from the converter without making the converter permanently unusable, and the electrical accessories cannot be opened by hand or general-purpose tools, such as screwdrivers. Whether they are qualified can be checked by observation.
Note: If the original parts or materials cannot be reassembled into a converter, the converter material is deemed to be permanently unusable. 14.2 Section. The content of the first five lines of 14.3 is changed to:
The converter pins should be:
GB 2099. 3 ---1997
locked and cannot rotate; its rotation does not affect its safety and function; cannot be removed without disassembling the converter:
After the converter is wired and assembled according to normal use, it should be firmly fixed in the body of the converter. When the converter pins are assembled and fixed according to the manufacturer's instructions, it should not be possible to reposition the grounding or neutral pins or contacts to any incorrect position:
14.4 The first paragraph is changed to:
The grounding socket and neutral socket of the converter should be locked during use and cannot rotate, and can only be removed with the help of tools after disassembling the converter.
14.11 The first line is changed to:
For rewirable intermediate converters:
14.13 is changed to:
If the cover of the converter is equipped with bushings for the pin insertion holes, it should not be possible to remove them from the outside; after the cover is removed, it should not be possible for them to accidentally fall off from the side A. Compliance is checked by inspection.
14.15 The content of the second paragraph is changed to:
After the converter is wired and assembled according to normal use requirements, there should be no other protrusions except the pins.
The content of the first paragraph is changed to:
The converter should be designed so that it will not be unable to fully engage with its corresponding plug due to any protrusions on the mating surface. 14.23 The first note is changed to
To: Electrical appliances integrated with the probe include converters, shavers with rechargeable batteries, lamps and plug-in transformers, etc. Add after the content of the first paragraph of 14.23.2:
For the converter, each socket part of the converter should first be plugged with the corresponding plug. The plug is equipped with a 1m long round flexible cable that meets the 2271EC53 standard and has a nominal cross-sectional area of ​​0.75mm. NOTE 1: The number of conductors shall be the same as the pole of the corresponding plug. Add the following at the end:
For converters, care shall be taken during the test to ensure that the free-hanging soft-plug is connected to the soft-plug. :
2L The following countries require higher torque values: Sweden - Converters equipped with the C2a socket part of the special IEC83 standard. A torque of 1.5Nm is required.
3 The basic specifications of the corresponding plugs and soft-plugs are under consideration. Add the following:
14.23.101 Converters shall be able to withstand the mechanical stresses that may be applied by the device inserted into them. Compliance is checked by the following test using the device shown in Figure 6. First, the specimen is mounted on a vertical surface so that the plane of the contacts with the core sleeve passes through the plane. The test surface shall be in a vertical position and parallel to the vertical mounting surface. Then insert the device and apply a weight of N vertically downwards to it for 1 min. Then remove the device and rotate the converter on the mounting surface by 90°. Test four times. The device shall not be pulled out during each test when the mating surface is rotated by 90°. This test shall be repeated for each socket part of the converter. After the test, the converter shall not be damaged within the meaning of this standard and shall comply with the requirements of Chapter 22 in particular. 14.24 is changed to:
Adoption Note:
1 Note 2 Not adopted in my country.
GB 2099. 3-- 1997
The shape and material of the converter shall be such that the converter can be pulled out from the corresponding socket by hand. In addition, the gripping surface shall be designed so that the converter can be pulled out without pulling the flexible cable or wire. Compliance is checked by one of the tests under consideration. Add the following content:
14.25 The content of GB2099.11996 is not applicable. Add the following content:
14.101 If any of the socket-outlets of a converter has an earthing socket or contact, the plug-outlet shall also have an earthing pin or contact.
Note: Converters that connect a socket-outlet with an earthing contact to a plug for electrical equipment without an earthing contact are not permitted. Compliance is checked by inspection and the test of 11.5. 14.102 Converters for use with polarized socket-outlets shall be designed so that the internal connections ensure that the pins of the socket, the socket and the terminals (if any) of the socket maintain the same polarity for the input and output parts of the converter. Compliance is checked by inspection and, if necessary, by an electrical continuity test. 14.103 It is recommended that the design and selection of multi-position converters should preferably be such that when plugged into a fixed socket-outlet installed in a concealed installation box, two or more multi-position converters should not be able to plug into each other. Compliance is checked by observation. Note: The above recommendation only applies to converters produced by the same manufacturer - unless detailed instructions are provided by the label of the specific system, it is not possible for multiple multi-position converters to be plugged into each other.
14.14 If the insulation requirements of the external flexible cable do not meet the requirements of the relevant national standards or the electrical strength between the cable and the metal wrapped outside the isolation layer specified in 17.2 does not meet the test requirements, the flexible cable shall be regarded as a bare conductor. 14.105 A suitable fuse group conforming to the relevant requirements of IEC Publication 269 shall be installed in the body of the converter with fuses (see 14.22).
The fuse shall be installed between the contacts of the converter plug pin and the corresponding phase socket socket. In polarity system A, the fuse shall be installed between the phase plug pin and the corresponding phase socket socket (or contact). The fuse shall not be installed in the grounding circuit. The converter shall be designed so that when assembled, the fuse will not be in a bad contact state. Compliance shall be checked by observation. 15 Interlocking sockets
Chapter 15 of GB 2099.11996 shall apply with the following changes. The title is changed to:
Interlocking socket part of converter
The content of the first paragraph is changed to:
The socket part of the switch interlocking converter should be designed so that the plug cannot be inserted into or removed from the socket when the plug is still energized, and the socket will not be energized until the plug is almost fully inserted. 16 Ageing resistance, protection against harmful water ingress and moisture resistance
Chapter 16 of GB 2099.1-1996 is applicable. 17 Insulation resistance and electric strength
Chapter 17 of GB 2099.1-1996 is applicable with the following changes. Adoption instructions:
1_ 14.103 Non-mandatory requirements in this standard are not required. 17.1.1 is changed to:
GB 2099.3—1997
For converters, the insulation resistance is measured in sequence between the following locations: a) between all poles connected together and the outer surface of external accessible parts made of insulating material, including external mounting screws; b) between each pole and all other poles connected together; () between any metal part of the cord fixing, including the clamping screw and the earthing pin or earthing terminal (if any); d) for cord-fixing converters, between any part of the cord fixing Between the metal part and the metal of the same thickness as the longest end of the cable (or cord) inserted in the normal position (see Table 17): Note
1 The test shall be carried out on easily accessible parts such as pins. 2 When the outer surface of the insulating material part is covered with metal or the metal is placed in contact with the inner surface of the insulating material part, the metal is placed in the hole in the same way as the standard test finger shown in Figure 2. 17.1.2 This clause of GB 2099.1-1996 does not apply. 18 Working of earthing contacts
Chapter 13 of GB 2099.1-1996 applies. 19 Temperature rise
Chapter 19 of GB 2099.1-1996 applies with the following changes. The seventh and tenth paragraphs are amended to read:
The converter shall be tested in a fixed position; the socket-outlet shall comply with the requirements of the standard and shall have as uniform characteristics as possible, but the earthing pin (if any) shall be of minimum size.
Insert the converter into the socket and pass the alternating current specified in Table 1(l[ for 1h. Add the following to the end of the thirteenth paragraph:
The test current passed through the conversion
-It must comply with the rated current of the corresponding socket part and pass through each single socket part in turn, and one must comply with the rated current of the converter and be divided in direct proportion to the rated value of the socket part, and pass through all socket parts at the same time.
20 Breaking capacity
Chapter 20 of GB2099.11996 is applicable after the following changes. The content of the second paragraph is changed to:
To determine whether it is qualified, use the test equipment shown in Figure 12 to test and inspect the socket part and the plug part with solid pins of the converter. The content of the fourth paragraph is:
The socket part of the converter shall be tested with a test plug. The test plug shall be The plugs shall be made of yellow steel and shall have the maximum specified dimensions with a tolerance of -0.06 mm and the distance between the plugs and the brackets shall be the nominal distance with a tolerance of 0.05 mm. It is sufficient as long as their dimensions are within the tolerance range given in the relevant standards. Add after the fifth paragraph:
The plug part of the converter shall be tested with a fixed socket that meets the requirements of the standard and has the characteristics of the line as much as possible. The content of the seventh paragraph is changed to:
Insert (in) and unplug (out) the plug part of the converter into the socket 50 times (100 strokes). The rate of pull-out is: 30 strokes per minute for converters with a rated current not exceeding 16A and a rated voltage of 250V, and 15 strokes per minute for other converters. Add before the second last paragraph;
GB 2099. 3-1997
Each socket part and plug part of the converter should be tested independently. 21 Normal operation
GB 2099.1-1996, Chapter 21, shall apply with the following changes. The content of the second paragraph shall be changed to
Whether the adapter is qualified, the socket part of the adapter with a resilient earthing socket contact or the plug part with a non-solid pin shall be tested with the test equipment shown in Figure 12.
Add a note after the tenth paragraph:
Note: The adapter is tested with a fixed socket that meets the requirements of this standard. The selected socket should be as uniform as possible: The content of the sixth paragraph shall be changed to:
Each socket part and plug part of the adapter shall be tested separately. The socket part of the adapter shall be inserted and unplugged 5000 times (10000 strokes), and the plug part of the adapter shall be inserted and unplugged 1000 times (2000 strokes). The insertion and removal rate is: for adapters with a rated current not exceeding 16A and a rated voltage not exceeding 250V, 39 lines per minute; - For other electrical accessories,15 strokes per minute 22 Force required to pull out the plug
GP2099.11996 Chapter 22 is applicable after the following changes. The content of the first paragraph is added as
The structure of the converter should make it easy to insert and remove the plug, and should prevent the plug from coming out of the socket part of the converter during normal use
22.1 The inner limit of the first paragraph is changed to
Fix the converter on the mounting plate A of the test equipment shown in Figure 13, so that the axis of the socket socket is vertical, and the plug of the wrong plug is facing downwards,
Table 101
Converter
Desired value of electrical accessories
250/4 40V
Test power
Chapter 19
Chapter 21
Plant area
Connected with flexible cable or cord
Non-detachable pilot converter
Test power
Chapter 19
Chapter 21
Note: For accessories with different rated current from those listed in the table, the test current should be between the higher or lower standard rated values. I insertion method to determine, 23 flexible cables and their connections
tB 2099.3 1997
(GB2099.1-1996 Chapter 23 is applicable after the following changes. The content of the first paragraph of 23.1 is changed to:
Intermediate converters should be equipped with wire fixing components to ensure that the wires are not subjected to forces including twisting at the connection points or at the ends, and the sheath of the wires is protected from wear. The first paragraph of 23.3 and Table 20 are changed to:
Non-detachable intermediate converters should be equipped with a flexible cable or cord that meets the requirements of IEC: Publication 227 or 245: The relationship between the cross-sectional area of ​​the wire and the rated value of the intermediate converter is given in the relevant column of Table 1: Table 101 The test current for temperature rise and normal operation test is also specified: The external cable or cord for control shall comply with the requirements of 14.1C4. The first paragraph of 23.4 is changed to:
Non-detachable intermediate converters with cables or cords shall be designed so that the cables or cords will not bend excessively at the point where they enter the converter. 24 Mechanical Strength
GB 2099. 1-1996 Section 21 Chapter 1: The following changes apply. The contents of the first and second paragraphs are as follows:
The converter has sufficient mechanical strength to withstand the mechanical stress generated during use. Compliance is checked by appropriate tests as specified below: For converters:
· Covers or bodies with non-elastic or non-thermoplastic outer shells... -24.2, 24.9\ and 24.10 · Covers or bodies with elastic or thermoplastic outer shells 24.2.21.4, 24.5.24.9 and 24.10 For plugs with insulating sleeves in the converter plug ··27 · For socket parts of converters with protective doors 2 4.·.24.2 Add after the fifth paragraph:
through the converter:
-50 times, if the weight of the sample does not exceed 50g: 25 times, if the weight of the sample exceeds 50g. The content of the last new number (——) is: When a torque of 1.0Nm is applied first in one direction and then in the opposite direction, the pin shall not rotate. Converters whose rotation of the pin will not endanger their safety and performance are not subject to this test: Finally add:
Note: Damage to the components of the intermediate converter is ignored only if the requirements of Chapter 1 are met and the operation of the equipment will not cause danger. 24.7 (The provisions of H2099.11996 apply. The content of the first paragraph of 24.8 is changed to;
The protective door of the entire part of the converter with a protective door should be designed to withstand the mechanical stress that may occur during normal use, for example, when the plug pin is forced into the protective door of the socket hole: 24.10 The content of the first paragraph is changed to;
As shown in Figure 25, place the converter on a rigid steel plate with holes for the pins of the plug part of the converter.) 2.! Only the socket part of the converter with flexible cable is used for the following assessment:
17 In GB 2099, 11996, delete "21.7. In this standard, the plug system in my country is required; t3 is treated as a companion. 25 Heat resistance
(B 20199. 1 Chapter 25 applies.
26 Screws, current-carrying parts and their connections
GB 2099. 1 Chapter 2G applies
GB 2099.3-. 1997
27 Electrical distances, electrical clearances and distances through sealants GB 2099. 1—1996 Chapter 27 of the Regulations shall apply with the following changes: The fifth dash in item 2 of Table 23 is changed to: External mounting screws. Except for screws on the mating surface of the converter and isolated from the grounded circuit. The content of item 3 is changed to: When fully plugged in, the plugs of the converter and the metal parts connected to the plugs and the small fusible and ungrounded metal parts of the socket, and these accessible parts are in the "most unfavorable structure"...-mm The content of item 4 is changed to: Between the accessible ungrounded metal parts in the socket and the fully plugged converter with the plugs and the metal parts connected to the pins made in the most unfavorable structure. The content of item 5 is changed to: Between the live parts of the socket part of the converter (without plug) and its accessible ungrounded metal parts:... Item 7 The fifth dash
of item 3 is changed to:
External screws. Except for the screws on the face of the converter and the screws that are isolated from the ground circuit - 3m27.1 The fifth paragraph is changed to:
The converter shall be checked when plugged into the socket and when plugged into and out of the corresponding socket. 28:1 Resistance of shrinkage materials to abnormal heat, flame and tracking GB 2099.1-1996, Chapter 28, applies. 29 Rust resistance
GB 2099.1-1996, Chapter 29, applies. 30 Additional test for plugs with insulators
GB 2099.1-1996, Chapter 30, applies.
Application Instructions:
[7] Since this product is a partial offset system, the contents of 28.1 and 28.1.2 of the joint insulation test are consistent with Chapter 28 of (13 2C99, :-19G).The contents of the first and second paragraphs are as follows:
The converter has sufficient mechanical strength to withstand the mechanical stress generated during the use of the components. Whether it is qualified is checked by appropriate tests as specified below: For converters:
· With non-elastic or non-thermoplastic outer cover or body... -24.2, 24.9\ and 24.10 · With elastic or thermoplastic outer cover or body** 24.2.21.4, 24.5.24.9 and 24.10 For the plug with insulating sleeve in the converter plug... 27 For the socket part of the converter with a protective door 24.2.24.2 Add after the fifth paragraph: | |tt||Through the converter:
-50 times, if the weight of the sample does not exceed 50g: 25 times, if the weight of the sample exceeds 50g. The content of the last new number (——) is: When a torque of 1.0Nm is applied first in one direction and then in the opposite direction, the pin shall not rotate. Converters whose rotation of the pin will not endanger their safety and performance are not subject to this test: Finally added:
Note: Damage to the components of the intermediate converter can be ignored only if the requirements of Chapter 1 are met and the operation of the equipment will not cause danger. 24.7 (The clauses of H2099.11996 apply. 24.8 The content of the first paragraph is changed to:
The protective door of the entire part of the converter with a protective door should be designed to withstand the mechanical stress that may occur during normal use, for example, when the plug pin is forced into the protective door of the socket hole: 24.10 The content of the first paragraph is changed to:
As shown in Figure 25, place the converter on a rigid steel plate with holes corresponding to the pins of the plug part of the converter. ) 2.! Only the socket part of the converter with a flexible cable is used as follows:
17 In GB 2099, 11996, "21.7" is deleted. In this standard, it is mentioned that the plug in my country needs a pin system; t3 is treated as a companion. 25 Heat resistance
(B 20199. 1 Chapter 25 applies.
26 Screws, current-carrying parts and their connections
GB 2099. 1 Chapter 2G Chapter Applicable
GB 2099.3-.1997
27 Electrical distance, electrical clearance and distance through sealant GB 2099.1—1996 Chapter 27 of the Regulations shall apply with the following changes: The fifth dash in item 2 of Table 23 is changed to: External mounting screws. Except for screws on the mating surface of the converter and isolated from the grounded circuit. The content of item 3 is changed to: When fully plugged in, the plugs of the converter and the metal parts connected to the plugs and the small fusible and ungrounded metal parts of the socket, and these accessible parts are in the "most unfavorable structure"...-mm The content of item 4 is changed to: Between the accessible ungrounded metal parts in the socket and the fully plugged converter with the plugs and the metal parts connected to the pins made in the most unfavorable structure. The content of item 5 is changed to: Between the live parts of the socket part of the converter (without plug) and its accessible ungrounded metal parts:... Item 7 The fifth dash Www.bzxZ.net
of item 3 is changed to:
External screws. Except for the screws on the face of the converter and the screws that are isolated from the ground circuit - 3m27.1 The fifth paragraph is changed to:
The converter shall be checked when plugged into the socket and when plugged into and out of the corresponding socket. 28:1 Resistance of shrinkage materials to abnormal heat, flame and tracking GB 2099.1-1996, Chapter 28, applies. 29 Rust resistance
GB 2099.1-1996, Chapter 29, applies. 30 Additional test for plugs with insulators
GB 2099.1-1996, Chapter 30, applies.
Application Instructions:
[7] Since this product is a partial offset system, the contents of 28.1 and 28.1.2 of the joint insulation test are consistent with Chapter 28 of (13 2C99, :-19G).The contents of the first and second paragraphs are as follows:
The converter has sufficient mechanical strength to withstand the mechanical stress generated during the use of the components. Whether it is qualified is checked by appropriate tests as specified below: For converters:
· With non-elastic or non-thermoplastic outer cover or body... -24.2, 24.9\ and 24.10 · With elastic or thermoplastic outer cover or body** 24.2.21.4, 24.5.24.9 and 24.10 For the plug with insulating sleeve in the converter plug... 27 For the socket part of the converter with a protective door 24.2.24.2 Add after the fifth paragraph: | |tt||Through the converter:
-50 times, if the weight of the sample does not exceed 50g: 25 times, if the weight of the sample exceeds 50g. The content of the last new number (——) is: When a torque of 1.0Nm is applied first in one direction and then in the opposite direction, the pin shall not rotate. Converters whose rotation of the pin will not endanger their safety and performance are not subject to this test: Finally added:
Note: Damage to the components of the intermediate converter can be ignored only if the requirements of Chapter 1 are met and the operation of the equipment will not cause danger. 24.7 (The clauses of H2099.11996 apply. 24.8 The content of the first paragraph is changed to:
The protective door of the entire part of the converter with a protective door should be designed to withstand the mechanical stress that may occur during normal use, for example, when the plug pin is forced into the protective door of the socket hole: 24.10 The content of the first paragraph is changed to:
As shown in Figure 25, place the converter on a rigid steel plate with holes corresponding to the pins of the plug part of the converter. ) 2.! Only the socket part of the converter with a flexible cable is used as follows:
17 In GB 2099, 11996, "21.7" is deleted. In this standard, it is mentioned that the plug in my country needs a pin system; t3 is treated as a companion. 25 Heat resistance
(B 20199. 1 Chapter 25 applies.
26 Screws, current-carrying parts and their connections
GB 2099. 1 Chapter 2G Chapter Applicable
GB 2099.3-.1997
27 Electrical distance, electrical clearance and distance through sealant GB 2099.1—1996 Chapter 27 of the Regulations shall apply with the following changes: The fifth dash in item 2 of Table 23 is changed to: External mounting screws. Except for screws on the mating surface of the converter and isolated from the grounded circuit. The content of item 3 is changed to: When fully plugged in, the plugs of the converter and the metal parts connected to the plugs and the small fusible and ungrounded metal parts of the socket, and these accessible parts are in the "most unfavorable structure"...-mm The content of item 4 is changed to: Between the accessible ungrounded metal parts in the socket and the fully plugged converter with the plugs and the metal parts connected to the pins made in the most unfavorable structure. The content of item 5 is changed to: Between the live parts of the socket part of the converter (without plug) and its accessible ungrounded metal parts:... Item 7 The fifth dash
of item 3 is changed to:
External screws. Except for the screws on the face of the converter and the screws that are isolated from the ground circuit - 3m27.1 The fifth paragraph is changed to:
The converter shall be checked when plugged into the socket and when plugged into and out of the corresponding socket. 28:1 Resistance of shrinkage materials to abnormal heat, flame and tracking GB 2099.1-1996, Chapter 28, applies. 29 Rust resistance
GB 2099.1-1996, Chapter 29, applies. 30 Additional test for plugs with insulators
GB 2099.1-1996, Chapter 30, applies.
Application Instructions:
[7] Since this product is a partial offset system, the contents of 28.1 and 28.1.2 of the joint insulation test are consistent with Chapter 28 of (13 2C99, :-19G).
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.