This standard specifies the requirements for the manufacture and acceptance of high-precision worm gear hobbing machines. This standard applies to high-precision worm gear hobbing machines with a maximum workpiece diameter of 500 to 2000 mm. JB/T 8361.2-1996 Technical requirements for high-precision worm gear hobbing machines JB/T8361.2-1996 Standard download decompression password: www.bzxz.net

Mechanical Industry Standard of the People's Republic of China
JB/T 8361.2--96
Technical Conditions for High Precision Worm Gear Hobbing Machine
Published on April 22, 1996
Ministry of Machinery Industry of the People's Republic of China
Implementation on July 1, 1996
Mechanical Industry Standard of the People's Republic of China
High Precision Worm Gear Hobbing Machine
Technical Conditions
1 Subject Content and Scope of Application
The standard specifies the requirements for the manufacture and light collection of high precision worm gear dissolving machines. This standard applies to high precision worm gear machines with a maximum workpiece diameter of 5~2000am. 2 Reference Standards
G55226
GR90S1
GBJ0089
3-139bzxz.net
JB/[ 8361.1
113/2 276
ZH JSCC3
ZnI5GGC4
ZB J5Q CC2.
Z8n J50 608.3
Z J50 C16
3 General requirements
General technical conditions
Machinery and electrical equipment
Machine tool lubrication system
Metal cutting machine pressure drifting non-standard conditions
Spindle worm, worm gear precision
Tide opening and breaking of the line of the country wheel
Technical conditions for the safety protection of metal cutting machine tools and machine tool accessories High precision gear hobbing machine special
Full screen cutting Determination of machine tool accuracy
Determination of noise level
Metal red-washing
Jin Teng machine tools
General technical requirements for machining parts
Jin filter cutting machine tools
Assembly general technical requirements
General technical requirements for acid pressing system
Jin need cutting machine tools
Precision classification of metal pre-press machine tools
JB/T 8361.2--96
3.1 This standard specifies and supplements the CBU061ZB150CC%.1.2BnJ5C008.3 and other standard sections. The machine tool must be inspected and tested in time for the remaining acceptance items of the above standard sections. 3.2 During the acceptance of the technical standard, the machine tool shall be inspected according to the requirements of the machine tool of grade 1 precision specified in the tool/7.87: 4 Accessories and tools
41 shall be the accessories and accessories engraved in the table 1 of the machine tool. 1.2 Expand the use of special accessories for machine tools. According to user requirements, they shall be provided according to the approval of the Ministry of Machinery Industry on April 22, 1996
1996-071-01
This is the spindle
Exchangeable step wheel
Can be used
5 Safety and Health
JR/T $361.2-96
Clamping and clamping, modification and monitoring of the machine tool, ensuring basic safety, adjustment and maintenance of the machine tool, installation of the machine tool, including the installation of the sleeves and pads on the auxiliary parts, leveling and modification of the nuts, etc. 5.1 The exposed teeth, pulleys and other parts on the machine tool that may cause personal injury and extreme damage must be equipped with safety protection devices. 5.2 When the machine tool is working, the parts where the cutting wave is flying must be equipped with reliable anti-shovel devices. 5.3 The horizontal guide rail of the machine tool should be equipped with protective devices. 5.4 The indexing worm and the tool holder worm should be equipped with viewing windows and position indicators. 5.51. After the worktable is stopped in an emergency, it shall not automatically resume function after the radial dynamic rapid movement and the rotation of the axis. 5.6 The worktable is equipped with a maximum travel limit device for the quick movement seat. The machine tool shall not make any unusual screams or impact sounds when the machine tool is running at low, medium and high speeds.8u0--1250
>1253--20ng
Section 1 Machine Tool Idle Running Test
JB/T8361.2—96
7.【The machine tool idle running test is to run the main motion mechanism at a speed from low to high speed for many times. The running time of each speed level shall not be less than 1h, and the speed increase rate shall not be less than 2 times. The main shaft shall be transported to a stable temperature, and the bearing temperature shall be measured at the position near the main shaft bearing. The value shall not exceed the provisions of Table 7.
Bearing type
Sliding shaft
Rolling technology is the most important
. 2. The hydraulic system should be operated in reverse under the designed working pressure, and the humidity should reach the fixed value. The temperature rise should not exceed 20%. 3. Inspection of radial motion and radial feed motion
Inspect the actual deviation of the shaft rotation and radial feed. They should not exceed ± % and 10% of the indicated value on the label respectively. 7.4 Action test
Start and stop the shaft in forward and reverse directions continuously for 10 times at medium speed to test the slowness and possible action of the movement. 7.5 Idle running power test (spot check)
After the main pump of the lathe runs idle at the stage speed until the power is stable, check the idle power of the main transmission system (referring to the no-load power of the motor), which shall not exceed the design requirements.
7.6 Light machine reverse idle running test
Simulate the working state under the function of the machine. The idle running test shall be carried out successively. The running time shall be at least ten days. No technical failure shall occur during the operation of the whole machine.
8 Machine tool precision inspection
8.1 The machine tool shall be carried out in accordance with FB/T8361.1
8.2 The precision inspection of the machine tool shall be carried out once and passed. The maximum allowable tooth surface roughness R of the test piece after precision flow is 1.2iur)9 Machine tool working test
According to the agreement between the manufacturer and the user, the same cutting specifications and methods for processing different types of test pieces shall be adopted. Additional Notes:
This standard was proposed by the National Metal Cutting Machine Tool Standardization Committee, compiled by Chongqing Yuanzhun Gear Machine Tool Research Institute and drafted by Wuzi.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.