JB/T 6040-1992 Inspection method for tightening torque of engineering machinery bolts
Basic Information
Standard ID:
JB/T 6040-1992
Standard Name: Inspection method for tightening torque of engineering machinery bolts
Chinese Name:
工程机械 螺栓拧紧力矩的检验方法
Standard category:Machinery Industry Standard (JB)
state:in force
Date of Release1992-05-28
Date of Implementation:1993-01-01
standard classification number
Standard Classification Number:Engineering Construction>>Construction Machinery and Equipment>>P97 Construction Machinery for Building Engineering
associated standards
Publication information
publishing house:Machinery Industry Press
Publication date:1992-12-01
other information
drafter:Meng Huijun
Drafting unit:Tianjin Forklift Research Institute
Focal point unit:Tianjin Engineering Machinery Research Institute of the Ministry of Mechanical and Electronic Industry
Proposing unit:Tianjin Engineering Machinery Research Institute of the Ministry of Mechanical and Electronic Industry
Publishing department:Ministry of Machinery and Electronics Industry of the People's Republic of China
Introduction to standards:
This standard specifies the inspection method for the tightening torque of bolts in construction machinery. This standard is applicable to the inspection of the tightening torque of bolts in construction machinery. JB/T 6040-1992 Inspection method for the tightening torque of bolts in construction machinery JB/T6040-1992 Standard download decompression password: www.bzxz.net
Some standard content:
P97
JB
Pressing Machinery Ring Industry Standard of the People's Republic of China JB/T60401992
D
1992-05-284
e
/4
1993-01-01 side
G20P xBe/
main
subject content and scope of application
D
this standard Specifies the inspection method for tightening torque of engineering machinery bolts. This standard is suitable for testing the tightening torque of bolts in construction machinery. 2 Inspection rules
Inspection tools
2.1
Torque wrench, adjustable wrench, scribe needle or scribe pen. 2.2 Inspection purpose
Inspect whether the tightening torque of the tightened bolts meets the specified value. 2.3 Inspection method
2.3.1 Method 1
JB/T60401992
For the tightened bolts, use a torque wrench to slowly and evenly move the bolt head (or nut) in the tightening direction. Rotation: If necessary, use an adjustable wrench to clamp the nut (or bolt head) connected to it accordingly to prevent rotation. When the bolt head (or nut) rotates for a moment, record the value, which is the tightening torque of the bolt. || tt | Make a mark with a pen, and then loosen the bolt head (or nut); if necessary, use an adjustable wrench to clamp the nut (or bolt head) connected to it accordingly to prevent rotation; then use a torque wrench to tighten slowly in the direction Rotate the surface evenly until the marks coincide with each other, and record the value, which is the tightening torque of the bolt.
2.4 The unit of measurement value is expressed in N·m.
2.5 The above two inspection methods are equally effective. Additional notes:
This standard is proposed and administered by the Tianjin Engineering Machinery Research Institute of the Ministry of Mechanical and Electronics Industry. This standard was drafted by Meng Huijun, the main drafter of this standard, with the capital of Guanjin Forklift Research Institute.
1992-05-28this
1993-01-01
1
Blue
》
D
Main
0
Political
E
60401992
JB/T
★
a
24
★
880A1230
1992 onwards 3m
100044
unitbZxz.net
1/16
3/8| |tt||1992A3m
1500
10.00 6
2,000
http://JB.ac.cn
609
L /ar
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.