JB/T 9836-2000 This standard is a revision of JB/T 9836-1999 "Technical Conditions for Clutch Driven Disc Assemblies for Tractors". The provisions for material selection of parts were deleted during the revision; technical requirements for torsional characteristics and durability were added. This standard specifies the technical requirements, test methods, inspection rules, marking, packaging, transportation and storage of clutch driven disc assemblies for agricultural tractors. This standard applies to dry and normally engaged friction clutch driven disc assemblies for agricultural tractors and agricultural transport vehicles. This standard was first issued in 1975 as NJ 73-75, revised for the first time in 1988 as ZB T63 005-88, and adjusted to JB/T 9836-1999 in April 1999. JB/T 9836-2000 Technical Conditions for Clutch Driven Disc Assemblies for Tractors JB/T9836-2000 Standard download decompression password: www.bzxz.net

ICS65.060.010
Machinery Industry Standard of the People's Republic of China
JB/T9836—2000
Technical Conditions
Specifications for tractor clutchdisk assemblies
Published on August 31, 2000
State Bureau of Machinery Industry
Implementation on January 1, 2001
Revision of "Technical Conditions for JB/T9836-2000".
This standard is a revision of JB/T98361999 (formerly ZBT6300588) "Total Cost Standard for Tractor Clutch Driven Discs". Compared with JB/T98361999, the main technical content changes are as follows: the material selection regulations for driven disc assembly parts have been deleted; the technical requirements for the torsional characteristics and torsional durability of the driven disc torsion damper have been added; the technical requirements for the performance and durability of the driven disc assembly with wave spring sheets have been added. This standard replaces JB/T9836-1999 from the date of implementation. This standard is proposed and managed by the National Technical Committee for Tractor Standardization. The drafting unit of this standard: Luoyang Tractor Research Institute. The main drafters of this standard: Luan Xinli, Liu Yaping, Yu Shuo. 1 Scope
Machinery Industry Standard of the People's Republic of ChinaWww.bzxZ.net
Tractor Clutch Driven Disc Assembly
Technical Conditions
Specifications for tractor clutch disk assemblies
JB/T9836—2000
Replaces JB/T98361999
This standard specifies the technical requirements, test methods, inspection rules, marking, packaging and storage of agricultural tractor clutch driven disc assemblies.
This standard applies to dry and constantly engaged friction clutch driven disc assemblies of agricultural tractors and agricultural transport vehicles. 2 Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T708—1988
GB/T 11441987
GB/T2828—1987
GB/T3478.1—1995
GB/T3478.2—1995
GB/T 57641998
JB/T6703.1—2000
3 General requirements
Dimensions, shapes, weights and permissible deviations of cold-rolled steel sheets and strips Dimensions, tolerances and inspection of rectangular splines
Batch-by-batch inspection Count sampling procedures and sampling tables (applicable to inspection of continuous batches) Module reference profile tolerance of cylindrical spur involute splines 30° pressure angle dimension table of cylindrical spur involute splines Automotive clutch facing
Test method for tractor clutch bench
3.1 The driven disc assembly shall comply with the requirements of this standard and shall be manufactured in accordance with the product drawings and technical documents approved through the prescribed procedures. 3.2 Main parts of the driven disc assembly
3.2.1 The materials and heat treatment of the main parts of the driven disc assembly shall comply with the requirements of product performance and service life. 3.2.2 All ferrous metal parts of the driven disc assembly should be treated with rust prevention: galvanizing, phosphating or oxidation, etc., but the spline hole should not be galvanized. 3.2.3
Spline hole of driven disc hub: The rectangular spline fit and spline groove shape and position tolerance should be in accordance with GB/T1144. The recommended fit is dH
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.