title>JB/T 8018.1-1999 Machine tool fixture parts and components V-blocks - JB/T 8018.1-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 8018.1-1999 Machine tool fixture parts and components V-blocks
JB/T 8018.1-1999 Machine tool fixture parts and components V-blocks

Basic Information

Standard ID: JB/T 8018.1-1999

Standard Name: Machine tool fixture parts and components V-blocks

Chinese Name: 机床夹具零件及部件 V 形块

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-08-06

Date of Implementation:2000-01-01

standard classification number

Standard ICS number:General, Terminology, Standardization, Documentation>>Vocabulary>>01.040.29 Electrical Engineering (Vocabulary)

Standard Classification Number:Machinery>>Process Equipment>>J44 General Fixture

associated standards

alternative situation:JB/T 8018.1-1995 (original standard number GB/T 2208-1991)

Publication information

publishing house:Mechanical Industry Press

Publication date:2004-05-30

other information

Focal point unit:Mechanical Science Research Institute

Publishing department:Mechanical Science Research Institute

Introduction to standards:

JB/T 8018.1-1999 This standard is a revision of JB/T 8018.1-95 "V-blocks for machine tool fixture parts and components". During the revision, only editorial changes were made according to relevant regulations, and the technical content remained unchanged. This standard specifies V-blocks with specifications of 9~85mm. This standard was first issued in 1981 as GB 2208-80, first revised to GB/T 2208-91 on April 30, 1991, and adjusted to JB/T 8018.1-95 in April 1996. JB/T 8018.1-1999 V-blocks for machine tool fixture parts and components JB/T8018.1-1999 Standard download decompression password: www.bzxz.net

Some standard content:

IC5 28.060.41
Mechanical Industry Standard of the People's Republic of China
Parts and components of jigs and fixtures
The parts and units of jigs and fixtures1999-08-06 Issued
State Machinery Industry Bureau
Implementation on 2000-01-01
Mechanical Industry Standard of the People's Republic of China
Parts and components of jigs and fixtures
V-blocks
The partx and units of jigs and fix1uresv-blork
This special standard specifies the shapes with specifications of 9-85mm. 2 Reference standards
JR/T8018.1-1999
IB/T80La.11955
The clauses contained in the following standards are used in this standard and constitute non-standard clauses. When a non-standard is published, the version is for implementation. All standards will be revised. Parties using non-standards should consider the possibility of using the latest version of the following standards. GH/699—1988 High-quality carbon absolute structural steel dialing conditions JH door 8044—1999 Machine tool fire and its parts and components - Technical requirements 3 Sizes
The sizes are shown in the following figure and table,
National Machinery Industry Bureau 1999-08-06 Approved 2000-01-01 Court
2 15 - 20 bzxZ.net
>260 - 25
>25 .- 35
>35-41
>45 - 60
811999
Note: Calculation formula for small T: H0
.5A:
4 Technical conditions
4.1 Material: 20 steel as per GA/T699, 13
4.2 Heat treatment: penetration depth 0.8-1.2mm, 58-MHRC4.3 Other technical conditions as per JA/T80M4 5 Marking
s.1 Marking Example:
W=74mm V-shaped block:
V-shaped fastener 24JB8018.1—1999
Limited energy curing
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.