This standard specifies the product classification, technical requirements, test methods, inspection rules, marking and packaging of hedge trimmers. This standard applies to hedge trimmers used for pruning various shrubs, hedge trees and garden flowers. QB/T 2289.5-2001 Gardening Tools Hedge Trimmers QB/T2289.5-2001 Standard download decompression password: www.bzxz.net

Gardening tools
Hedge trimmer
QB/T 2289.5—2001
This standard is based on the requirements of the State Bureau of Technical Supervision to clean up and rectify national standards, and is converted from the original national standard GB68691986 "Hedge trimmer" to an industry standard (this standard was issued by the National Light Industry Bureau [19991112 Document No. 12) and the conversion standard number is QB/T3855—1999, with the same content).
This standard is proposed by the General Business Department of the China Light Industry Federation: This standard is under the jurisdiction of the National Tool Hardware Standardization Center. This standard is drafted by the Shanghai Tool Industry Research Institute, and Jiangsu Zhangjiagang Fulai Garden Tools Co., Ltd., Shandong Garden Tools General Association, Jiangsu Jinlu Group Co., Ltd., and Dongjiexi Knife and Scissors Factory participated in the drafting. The main drafters of this standard are Lin Meide, Ji Jianrong, Meng Xiangtuan, Jun Xuehai, and Ri Xikui. From the date of implementation of this standard, the industry standard QB/T3855-1999 "Hedge Trimmers" issued by the former State Light Industry Bureau shall be abolished.
Light Industry Industry Standard of the People's Republic of China
Gardening ToolswwW.bzxz.Net
Hedge Trimmers
QB/T 2289.5--2001
Replaces QB/T3855-1999
This standard specifies the product classification, technical requirements, test methods, inspection rules, marking and packaging of hedge trimmers. This standard applies to hedge trimmers for pruning various shrubs, hedge trees, and gardening flowers. Referenced Standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is revised, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest version of the following standards.
GB/T230-1991Metallic Rockwell Hardness Test MethodGB6867—1986Inspection Rules, Marking and Packaging of Gardening Tools3Product Classification
3.1Type
The types of shears are shown in Figures 1 to 3, and are divided into true line blade (indicated by A), curved blade (indicated by B) and serrated blade (indicated by C) according to the shape of the shear blade. 3.2Basic Dimensions
The basic dimensions of shears are in accordance with the provisions of Table 1. Table 1
3.3Marking Examples
The marking of the product consists of the product name, specification, type code and standard number. 300mm serrated blade full-length shears marking example:
QB/T 2289.5-2001
Full-length pipe shears 300mm
Approved by China Light Industry Federation on 2001-07-16
TYKAONIKAca
Made of steel plate
2001-11-01 implementation
QB/T 2289. 5—2001
Figure 1 True-line blade hedge shears
Figure? Parallel-line full-length shears
Figure 3 Serrated blade full-length window shears
4 Technical requirements
4.1 Hardness
Q/T2289.5--2001
The blade hardness of the hedge shears is 43HRC~48HRC. 4.2 Performance
4.2.1 The shear head should be flexible to open and close, the shear handle must be firmly assembled, the buckle is tight, and there is no grinding or pinching of the hand. 4.2.2 The shear blade should be sharp, the blade line should be neat, there is no chipping or curling, and the shear blade should be tightly closed. 4.3 Surface quality
4.3.1 The surface of the whole shear should be smooth, without burrs, cracks, flash, oxide scale and other defects. 4.3.2 The surface roughness of each part of the whole shear should comply with the provisions of Table 2. Table 2
Surface roughness
4.3.3 When the handle of the trimming shear is decorated with plastic or organic paint, its surface should be uniform and bright, without adhesion, dripping and obvious flow marks.
4.3.4 The surface of the trimming shear should be polished, blackened or other surface treatments. The surface of the trimming shear after surface treatment should have a uniform protective layer, and there should be no bottom exposure. 5 Test methods
5.1 Hardness test
The hardness test is carried out on the cutting edge according to the provisions of GBT230. 5.2 Dimension and surface quality inspection
5.2.1 The size of the whole shears is inspected with a special cardboard or a universal measuring tool. 5.2.2 The surface roughness before trimming is inspected by comparison with a standard sample. 5.2.3 The appearance quality of the whole shears is inspected by visual inspection. 6 Inspection rules, marking and packaging
The inspection rules, marking and packaging of the whole shears are in accordance with the provisions of GB/T 6867. 9
KAONKAca
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.