This standard specifies the marking method and mesh size series for industrial metal wire mesh, perforated plate and electroformed sheet. This standard applies to metal mesh such as industrial metal wire mesh, welded mesh, perforated plate and electroformed sheet; it also applies to non-metal mesh made by various processing methods. GB/T 10611-2003 Industrial mesh marking method and mesh size series GB/T10611-2003 standard download decompression password: www.bzxz.net
This standard specifies the marking method and mesh size series for industrial metal wire mesh, perforated plate and electroformed sheet. This standard applies to metal mesh such as industrial metal wire mesh, welded mesh, perforated plate and electroformed sheet; it also applies to non-metal mesh made by various processing methods.
Some standard content:
GB/T10611—2003 This standard is modified to adopt ISO2194:1991 "Methods for marking industrial mesh wire woven mesh, perforated sheet and electroformed sheet and basic size series of mesh holes" (English version). The main changes are as follows: Appendix A is added to make the standard easier to implement. This standard replaces GB/T10611-1989 "Mesh hole size series for industrial mesh". Compared with GB/T10611-1989, the main changes of this standard are as follows: the content of Table 2 is adjusted, and the content of Table 3 is supplemented; the marking method is added. Appendix A of this standard is an informative appendix. This standard is proposed by the China Machinery Industry Federation. This standard is under the jurisdiction of the National Technical Committee for Standardization of Screen Screening and Particle Sorting Methods (CSBTS/TC168). The drafting units of this standard are: Mechanical Science Research Institute, State-owned No. 540 Factory. The main drafters of this standard are: Yu Fang, Dong Wei, and Wu Guochuan. This standard is interpreted by the Secretariat of the National Technical Committee for Standardization of Screen Screening and Particle Sorting Methods. The previous versions of the standards replaced by this standard are: GB/T10611-1989. 1 Scope Industrial mesh Marking method and mesh size series GB/T 10611--2003 This standard specifies the marking method and mesh size series of industrial metal wire woven mesh, perforated plate and electroformed sheet. This standard applies to metal mesh such as industrial metal wire woven mesh, welded mesh, perforated plate and electroformed sheet; it also applies to non-metallic mesh made by various processing methods. 2 Normative references The clauses in the following documents become the clauses of this standard through reference in this standard. For all dated referenced documents, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties to agreements based on this standard are encouraged to study whether the latest versions of these documents can be used. For any undated referenced document, the latest version shall apply to this standard. GB/T321 Priority numbers and priority number systems GB/T6005 Basic dimensions of mesh holes of test sieves, wire mesh, perforated plates and electroformed sheets (eqvISO565:1990) GB/T10061 Method for marking mesh holes of sieve plates (egvISO7806:1983) GB/T15602 Industrial sieves and screening terms (eqvISO9045:1990) 3 Terms and definitions The terms and definitions in this standard adopt those in GB/T15602. 4 Marking method 4.1 Overview In the mesh size series, when it is equal to or greater than 1mm, the unit is expressed in millimeters (mm); when it is less than 1mm, the unit is expressed in micrometers (μm). 4.2 Wire mesh Wire mesh should be marked with the basic mesh size, weaving type, nominal size d and wire material. 4.3 Perforated plate Perforated plate should be marked with the basic mesh size z (distance between the midpoints of opposite sides or mesh diameter), mesh shape (square hole, round hole or other regular geometric shape), plate thickness and perforated plate material. It is recommended to use the perforated plate marking method specified in GB/T10061. 4.4 Electroformed sheet Electroformed sheet should be marked with the basic mesh size, mesh shape (square hole or round hole) and the name "electroformed". Its holes are made by electromachining. 5 Mesh size series 5.1 The mesh size is divided into the first series, the second series and the third series, which are R10, R20 and R40 respectively. The first series (R10) is preferred. For the size series with mesh size less than 50um, they are R'10, R20 and R'40. 5.2 See Table 1 and Table 2 for the size series of mesh. 5.3 Method of expressing size units For mesh size equal to or greater than 1mm, the unit is expressed in millimeter (mm) (see Table 1); for mesh size less than 1mm, the unit is expressed in micrometer (μm) (see Table 2 and Table 3). 1 GB/T 10611-2003 (first series) (second series) Mesh size series (third series) (first series) (second series) Unit: mm (third series) (first series) (first series) (second series) Table 1 (continued) (third series) (first series) (second series) Mesh size serieswwW.bzxz.Net (third series) (first series) (second series) GB/T 10611—2003 Unit is millimeter (third series) Unit is micrometer (second series) (third series) GB/T 10611-2003 (First series) (Second series) (Third series) Mesh size series (First series) (Second series) Unit: micrometer (Third series) Appendix A (Informative Appendix) Examples of mesh shape and size symbols GB/T10611-2003 A.1 A mesh made of holes formed by metal wires or non-metallic wires, the mesh shape and size of the metal wire woven mesh are shown in Figure A.1. Figure A.1 Mesh shape and size A.2 A mesh made of holes formed by metal plates or non-metallic materials by stamping or other processing methods, the mesh shape and size of the metal punching plate are shown in Figure A.2. Figure A.2 Mesh shape and size Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.