Some standard content:
Mechanical Industry Standard of the People's Republic of China
JB/T85861997
Glazing Machine
Published on 1997-06-20
The Ministry of Machinery Industry of the People's Republic of China
Implemented on 1998-01-01
JA/T 8581997
This standard is proposed by the National Technical Committee for Printing Machinery Standardization. The drafting unit of this standard is Shanghai Yahua Printing Machinery Co., Ltd., and the main drafter of the technical standard is Zhu Lihua.
Mechanical Industry Standard of the People's Republic of China
Glazing Machine
JB/T85861997
This standard specifies the type and cost parameters, labor requirements, test methods, temporary rules, installation, production, and other requirements of single-sided printed fabric glazing machines (hereinafter referred to as glazing machines). Wood: H-type UV, external load 10 laser machine, used for the two-photon unit, the following is called online photon unit. 2 Reference standards
The text contained in a standard also constitutes the provisions of this standard through the reference in this note. When the standard was published, the total version shown is consistent. All products shown will be affected. The use of this standard should explore the possibility of using the latest version of the following standards: GBSI SC
GBr184-1996
GB467R5
GB5226—85
GREARS-B
G3 891.3-H8
G3/T133C691
G5/T 12381-02
16 3660 - 82
3 Classification and basic parameters
3.1 Classification
Packaging storage and transportation graphic mark
Shape style and position and public case delivery tolerance
European leading packaging
Machine tool electrical equipment source H technical water conditions
Transportation index loading and delivery mark
Paper and new board mirror surface non-deformation determination methodWww.bzxZ.net
Single determination
Machine book product packaging general technical regulations
That is, the machine lacks production and type reduction method
3.1.1 According to the combination of design:
a) Special glazing machine:
b) Family glazing machine group.
3.1.3 According to the chemistry:
) Automatic glazing machine;
b; Semi-automatic glazing machine.
3.2 Number of vehicles 5 Table 1
White Dynamic F Optical Institute
Approved by the Ministry of Machinery Industry on 1997.06-20
Recorded large tensile wing
>1626--14*
>526--1020
-Ic2c --1440
E20-59
Contact us
1998-01-01 implementation
3.3 Production No. Name according to 733090, 4 Technical requirements
JB/85861997
4.1 1. The machine shall comply with the provisions of this standard and be manufactured according to the approved drawings and technical documents. 4.2 The design of the glazing machine shall be the most important, and the auxiliary coating (agent drive) and other auxiliary equipment shall be provided. The parallelism and polishing performance shall be guaranteed. The parallelism between the two radial axes shall be as shown in Table 2.
Assembly glazing machine
Semi-automatic glazing machine
The parallelism between the axes shall be limited to the change of G6/T84-136 double B2 cage 6. /-1556 The setting period of the table
should be late, the dynamic system is normal, there is no abnormality, 4.4 The operation is reliable, the mechanism action is correct: no card limit buckle occurs, 4. The mother system is smooth, the bearing working condition will not be higher than: 35, the upper optical cloth layer should be smooth, there should be no quilting, tearing, no obvious streaks, no sticking ring phenomenon on the upper layer, 4.6
Even if the cloth layer is reversed, the position of the skin is not correct, 3
The largest piece
Automatically hit the heart
A group
2:20~120
4.8 The dynamic glazing machine is late in the market, and the semi-dynamic glazing machine works without noise 8B4.9 Safety meeting
4.9 .1 Safety protection equipment can be fully adopted, and there is a degree of gas installation 4.5.2 Electrical socket || tt || 4.2.1 The short circuit between the dynamic circuit and the protection circuit (including the base) is not too small: 1. 4.9.2.2 The external protection wire and the electrical equipment are connected. The value between the two conductors and the shell is not more than 0.1. 4.9.2.3 Electrical equipment must: 1m attached pressure test. The test voltage is 15V. There should be no breakdown or circuit. 4.9 Quality measurement || tt || 4.10.1, the exposed processing length shall not have any damage. ± It shall not be embedded in it. 4.2 The processing surface of the external device shall not have any defects such as concave, roughness, etc., and the paint layer shall be flat and smooth, and the color and gloss shall be uniform, and the components shall be prominent and glued. All goods must be rented to the standard, and there must be no flow, blistering, gloss loss, etc. 4.4 The specifications of the equipment should be listed in order 4.11 Product components
) The main machine (including ground, coating, blasting, paper collection and other parts): 2
b) Necessary equipment and maintenance:
c) Necessary tools for operation and maintenance,
5. Test method
5. Idle operation test
JH/T85861997
The coating machine must be tested for no less than 120 minutes of idle operation every year. The speed should not exceed 15min. 5.1 Idle operation inspection
Monthly visual inspection of these idle operation conditions, which should meet the judgments of 1.3 and 4.4. 5.1.2 Safety inspection
Daily visual inspection to see if the safety protection and gas devices meet the requirements of 2.9.1. 5.1.3 First test the safety performance of the gas generator
5.1.3. After the insulation resistance meets the requirements of 4.9.2.1, 5.1.3.3. After the insulation resistance meets the requirements of 4.9.2.1, 5.1.3.3. After the insulation resistance meets the requirements of 4.2.2, 5.1.3.3. After the insulation resistance meets the requirements of 4.9.2.3, 5.1.3.3. After the insulation resistance meets the requirements of 4.9.2.3, 5.1.3.3. After the insulation resistance meets the requirements of 4.9.2.3, 5.1.3.3. After the insulation resistance meets the requirements of 4.9.2.3, 5.1.3.3. After the insulation resistance meets the requirements of 4.9.2.3, 5.1.3.3. 5.3 It is necessary to eliminate the parallelism of the test machine in the air test. The scale and scale are used to measure the parallelism of the polishing machine, cold work stamping, etc. The values should be derived from 4.2. 5.4 The test
The polishing machine is used to record the high-speed rotation of the air machine. The sound level is verified by the ordinary sound level measurement machine. The sound transmission height is 1: The machine is used at four external measurement points, and its arithmetic average and value should be calculated according to the production specifications. 5.5 printing product diagnosis and appraisal
5.5.1. Inspection of the city's glazing machine, the monthly and night operation speed
and the maximum running time of the machine are specified. The new paper reduction of Sichuan C--250/m rubber single cloth is adopted, and the automatic glazing machine and the online glazing machine unit are under R3 high quality glazing treatment, and the glazing machine is driven at 1% high glazing speed, and the glazing is carried out in reverse. 5.5.2 During the quality inspection, the product flow shall be randomly selected from the top 100 sheets, and the sample sheets shall be checked for quality. The order of the printed product shall be in accordance with the specifications of 4.G. 5.5.3 The uniformity of the micro-layer of the product shall be tested by using a pressure-controlled mathematical instrument to measure the light intensity values of 10 positions at 2mm on the top 10 sheets and the top 10 positions respectively. Then the top 10 sheets shall be randomly selected and put into the 100 non-light groups for light testing. Then the light intensity values of the same positions on the left and right sheets shall be measured separately. The light intensity values A shall be given below. The values shall meet the requirements. The table is Yuebao,
24.A..Yuan
Wu Zhong, .-.Year Accounting,=.
Test the most mail serial number.1.3.-5
-Number of samples=10.
5.6 Quality inspection
Daily visual inspection of the product has been recorded and produced, and the production should comply with the provisions of 4.1. 3
5.7 Enterprise inspection
JD/T8586-1997
Daily visual inspection of the product supply standard, the results should comply with the provisions of 4.11. Inspection rules
6.1 Factory control inspection
1.1 Each product must be inspected by the quality inspection department of the manufacturer before it can be shipped. 6.1.2 Before each product is shipped out, the quality inspection department shall conduct a quality inspection according to 5.1.1, 5.1.2, 5.1.3.1, 3.1.3.2, 5.2.5.3.5.6.5.7 of this standard. If any item fails to meet the standard, the product shall be deemed as a defective product. 6.1.3 Each batch of glazing machines shall be strictly inspected in 1, 5.5. If the item is unqualified, it can be reversed. If it is still unqualified, test each unit one by one.
6.2 Type test
62.1 Type test is carried out in the following situations: a) New products or old products are switched to production trial and adjustment: b) After formal production is stopped, if there are major changes in structure, material, and process that may affect product performance: e) When the product is discontinued and production is resumed.
6.2.2 Type test shall be carried out in accordance with vehicle standards. The test report shall be provided, and the marking, packaging, transportation, storage and machine documents shall be provided. 7. Marking
7.1.1 The quality label of each product shall be marked on the marked part according to the requirements of (B/1:13306). The label shall include: manufacturing name:
b) product model, name:
e) product date (or batch number) or production batch number.
7.1.2 Product packaging, storage and transportation labeling shall comply with the relevant provisions of 11. All packages with the center of gravity obviously deviating from the center should be marked with "from here" and "weight". 7.1.3 The delivery and receiving marks of the transport packaging should comply with the provisions of G56352. 7.2 Packaging
7.2. Before packaging the product, the outer surface of each tool and tool should be treated with anti-rust packaging of GB4879-R3. The packaging should be graded as grade 1
7.2.2 The product should also be packed in a box 7.3 When transporting products, please pay attention to the markings on the outside of the packaging box and handle them carefully. 7.4 When storing products at night, they should be stored in a place away from wind to avoid being damaged. When storing them outdoors, the packaging should also be properly stored. If the storage period exceeds two years, the packaging should be opened and rectified before shipment. If the packaging does not comply with the relevant regulations, it should be repacked. 7.5 When packing the product, please include the maintenance certificate, certificate of conformity, packing list, etc. When packing the product, the box should be replaced with a color box.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.