GB 5198.2-1996 Antibiotic glass bottle caps Part 2: Aluminum-plastic combination caps
Some standard content:
GB 5198.2-1996
This standard is the first revised version of GB5198-85 "Aluminum caps for antibiotic bottles". This standard is equivalent to 1S08362-6:1992 "Injection containers and accessories - Part 6: Aluminum-plastic composite injection bottle caps" and 1S)83627:1995 "Injection containers and accessories - Part 7: Flangeless aluminum composite injection bottle caps" and 1S)10985:1992 "Aluminum-plastic composite bottle caps for infusion bottles and injection bottles - Requirements and test methods". GB 498 Standard for Antibiotic Glass Bottle Caps includes the following two parts: GB5198.1 Antibiotic Glass Bottle Caps Part 1: Aluminum Caps: (F13·5198.2 Antibiotic Glass Bottle Caps Part 2: Aluminum-Plastic Combination Caps: GB5198-85 is replaced by GB5198.1-1996. The content of this standard is the new content of this revision. The appendixes of this standard are the appendices of the standard.
Appendix B and Appendix C of this standard are indicative appendices. This standard is proposed by the State Food and Drug Administration
This standard is under the jurisdiction of the Shandong Pharmaceutical Packaging Materials and Container Product Quality Inspection Center of the State Food and Drug Administration. The main drafting units of this standard: Shandong Pharmaceutical Packaging Materials and Container Product Quality Inspection Center of the State Food and Drug Administration, Gonghai Jiuan Packaging Industrial Co., Ltd.,
Participating drafting units of this standard: Shijiazhuang Nonferrous Metal Processing Plant, Shandong Weihai Changming Beverage Packaging Company The main drafters of this standard are Sheng Ping, Zhang Liqing, Cai Ye, Zhao Ying, Guan Chuangfeng CB 5198.21996
ISO Foreword
1ISO (International Organization for Standardization) is a world federation of national standards bodies (ISO member bodies). The work of formulating international standards is usually carried out by technical committees of ISO. If each member body is interested in a project established by a technical committee, it is welcome to participate in the work of the committee. International organizations (official or unofficial) that maintain contact with ISO () may also participate in the relevant work. In terms of electrical technical standardization, ISO (tt||) maintains a close cooperative relationship with the International Electrotechnical Commission (IEC). In this regard, the draft international standards adopted by the technical committees of ISO (tt||) are submitted to the member bodies for voting. They must be approved by at least 75% of the member bodies participating in the voting before they can be officially published as international standards. International standards ISO 53626 and ISO 5362-7 were formulated by ISO/TC76, the International Organization for Standardization Technical Committee for Medical Transfusion, Infusion and Injection Equipment.
ISO8362 general standard for injection containers and accessories, including the following parts: Part 1: Glass tube injection bottles;
Part 2: Injection bottles;
Part 3: Aluminum caps for injection bottles;
Part 4: Molded glass injection bottles
Part 5: Freeze-dried stoppers for injection bottles; : Part 6: Aluminum-plastic combination injection bottle caps; Part 7: Flangeless aluminum-plastic combination injection bottle caps 182
17bz.cnCrisp lotus root
17jzw.comCrisp bear rate
He demon meal lotus root
Qing he iron cuit pear
1 Ying60 meal
1 Scope
National Standard of the People's Republic of China
Antibiotic glass bottle caps
Part 2: Aluminum-plastic combination caps
Caps for injection glass vials of antihioticsFart 2: Caps made of al uminium-plaslics combinationsGB 5198.2--1996
qv 1so 8362-6: 1992
eqx 1S0 8362-7:1995
This standard specifies the types, dimensions and tolerances, marking, requirements, test methods, marking, packaging of aluminum-plastic combination caps for antibiotic bottles as described in GB2610-90) and (B2641-90) 2 Reference standards
The following standards contain provisions that constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. Parties using this standard should explore the possibility of using the latest versions of the following standards. G13 228-187
Metal tensile test method
GB/T 1801—92
General tolerances for linear dimensions without specified tolerances
GB2640-90 Moulded antibiotic glass bottles
GB 26419U
Controlled anti-dust glass bottles
GB2828r
GI32829+87
Batch-by-batch inspection set counting sampling procedures and sampling tables (applicable to inspection of continuous batches) YY 0169 2--94
Butyl rubber anti-oxin bottle stopper
3 Type classification
Bottle caps are divided into the following types:
Type ZB: composed of aluminum parts with center holes and plastic parts with flanges; Type 21): composed of aluminum parts with tear-off tabs and plastic parts with flanges; Type B: composed of aluminum parts with center holes and plastic parts without flanges; Type D: composed of aluminum parts with tear-off tabs and plastic parts without flanges. 4 Dimensions and tolerances
Various types of bottle caps (flat, ring or other shapes) should comply with the dimensions specified in Figure 1 and Table 1. 1: The configuration of the bottle caps in the figure is for reference only. Approved by the State Administration of Technical Supervision on December 2, 1996, and implemented on July 1, 1997
ZB, ZT
GB 5198. 2
Material Parts
Companion: 3-Grade Line
Bottle Cap Structure
Bottle Cap Size
1) az should be agreed upon by both the supplier and the buyer, and should not exceed the nominal value ± 0.25mm. Only the limit value is given in the table, and the tolerance is not specified. 2) Approximate hole diameter after removing the plastic parts.
3) It is determined by negotiation between the supply and demand parties. It should not exceed the nominal position of 122mm. The table only gives the limit value and does not specify the tolerance. 2) The h layer is determined by negotiation between the supply and demand parties. It should not exceed the nominal position of 6.3mm. The table only gives the limit value and does not specify the tolerance. trhiri
5) 20a ground cover is applicable to type A molded bottles in 1 (+H2640) and type A plugs in YY169.2. 20b bottle caps with h of 7.3mm are applicable to type B molded bottles in GB2640 and type RI plugs in YY 0169.2; 20h cover with h of 6. Hmm is applicable to type GB 2641 molded bottles and YY 0169.2 Type A plug: If used for the matching type of other bottles and plugs. The nominal size is determined by negotiation between the supply and demand parties between 6.17.8mm, 4.2 Tolerance
Capping technology Note: The tolerance should comply with the m-level requirements in (GB/T1804. 1h.
Both thin travel science 5 fin lake
17bzW.cn crisp wall lotus
17jizw.com crisp bear throw
other helmet lotus jaw
1 Ji Ying 60
5 marking
GB 5198. 2
The marking consists of "bottle cap", this standard, type and nominal size. Example: Hot run this standard, nominal size 20a:71) type aluminum-plastic combination bottle cap is marked as moving cap GB 5198.2-ZD-20a
6 Requirements
6.1 Mechanical properties
The mechanical properties of aluminum materials shall meet the requirements specified in the three categories A, B and C in Table 2. Note 2: Appendix C lists the chemical composition of commonly used lead alloys Table 2 Mechanical properties of aluminum materials
Aluminum alloys
Annealed or coated AIFCSI
AIFeSi
1) Other aluminum alloys may also be selected if they meet the mechanical properties specified in this table. 6.2 Appearance quality
Tensile strength
[01-~:50
130-~170
14G-180
The bottle cap should be clean. There should be no residual lubricant, burrs, damage and injection flash: the plastic part should be completely connected with the lead part. 6.3 Convex edge
The convex edge of the aluminum part of the bottle cap should not be greater than 3mm.
6.4 Opening force
6.4.1 When testing according to the method specified in the previous section A, the tearing force required to remove plastic parts and disconnect ZD or (D) type aluminum parts shall generally meet the requirements of Table 3
Table 3 Removal force and tearing force
Nominal size
Plastic part removal force
Tearing force
6.4.2 The minimum tearing force required to remove plastic parts and tear off ZD or (OD) type aluminum parts shall meet the agreed value between the supplier and the buyer. 6.5 Steam and fire resistance
The bottle cap is 7.5.After the process specified in 7.5.1 and 7.5.2, the plastic parts shall not be deformed or discolored, and the surface of the aluminum parts shall not have any obvious changes. The parts shall also be able to withstand the steam sterilization temperature of 130 for a short time (maximum 5 minutes) without deformation or discoloration. Note 3: Ordinary aluminum alloys tend to produce marks when sterilized in a steam sterilizer. 6.6 Matching
After the process specified in 7.5.1 and 7.5.2, the bottle cap shall be matched with the appropriate medium. 6.7 Strength
After the process specified in 7.5.1 and 7.5.2, the bottle cap shall not be broken or abnormally deformed. 6.8 Opening quality
When the bottle cap is subjected to the opening force test, after removing the material (opening the bottle cap), the opening of the aluminum part shall not be damaged. 6.9 Coating firmness
GB 5198.2--1996
For aluminum parts with coating on the outer surface, there should be no signs of coating wear after the test in 7.6. 6.10 Process requirements
The assembly of aluminum parts and plastic parts should be carried out in a clean state and ensure that the assembled bottle caps are not contaminated. 7 Test methods
7.1 Mechanical properties
The mechanical properties (tensile strength and elongation) of aluminum parts should be carried out in accordance with the provisions of GB228. Certificate 4: Bottle cap manufacturing! The mechanical properties test and chemical composition analysis report of the aluminum material supplier can be received. 7.2 Appearance quality
Visual inspection.
7.3 Size
Inner diameter is inspected with limit gauge. Other dimensions are checked with general measuring tools such as vernier calipers, height gauges and micrometers. 7.4 The convex edge defects of the four sides
aluminum parts are calculated as a percentage according to formula (1) hue
where: hmax
the maximum height of the outer side of the bottle cap aluminum part;
the minimum height of the outer side of the bottle cap aluminum part.
Note: The surface drawing is enlarged to illustrate the maximum and minimum height of the outer side. Illustration of the convex edge of the bottle cap
7.5 Sterilization resistance, compatibility, strength
7. 5. 1 Steam sterilization process
Saturated steam treatment:
Heating time 30min;
Maintaining time 12℃±2℃30min (including 130℃±2℃5min); cooling time 30min to 60℃
7.5.2 Capping process: Cover the antibiotic glass bottles that meet (B2G40 or GB2641 with stoppers that meet YY0169.2, and add caps: Cap with a capping device
7.6 Coating firmness
Aluminum parts with coating on the outer surface: After 7.5.1 and removing the plastic parts, Immerse it in 80% (V/V) ethanol aqueous solution for 30 minutes, wipe the surface with absorbent cotton,
8 Marking, packaging
8.1 Marking
The packaging should have the following clear markings:
a) manufacturer's name;
b) product mark;
production batch number or date;
5
17bzw.cnCrisp Lotus Root
17jzw.comCrisp Bear Rate
He Yao Can Bian Lotus Root Color
Qing Tie Cui Pear
1 Ji Ying 60
GB 5198.2-1996
8.2 The packaging should ensure that there is no adverse effect on the performance of the bottle cap during transportation and storage and prevent any pollution. The inner packaging should be made of plastic bags. The outer packaging shall be in cartons or paper barrels that can withstand standard transport conditions. 187
A1 Equipment
GB5198.2---1996
Appendix A
(Standard Appendix)
Opening force test method
With Figures A1~A3 Special accessories as shown in the / compression testing machine, drive speed = 100rutn/tin, large range hand 1 (00N plastic part removal force
A2.1Z type and ZL) type bottle caps are shown in Figure A1.OB type and (L) type bottle caps are shown in Figure A2. Clamp the bottle caps on the special clamping screen and apply force to remove the plastic parts
Force application direction
Press rod size
Nominal size
Both traces Zhang Ke 5
ZB type and ZD type plastic part removal force testing device 17bzw.cn Crisp Bi Lotus
17izw.com Crisp Bear Rate
He Iron Cai Whip Lotus Color
With the type of iron friction
1 Ji Ying 60
Nominal size
GB 5198.2
Force direction
Degree
Figure A2 (Test device for removing force of type B and type OD plastic parts A2.2 Record the maximum force required to remove the plastic parts. A3 Tear-off force
As shown in Figure A3, the hook is hung on the exposed tear-off piece and the tension and compression testing machine is used to apply force in the direction shown in Figure A3 until the bottle cap is completely torn off. 189
Nominal size
GB 5198.2—1996
Force direction
Spindle size
Figure A3 Tear-off force test device
Appendix B
(Suggested appendix)
Inspection rules
B1 Product inspection is divided into factory inspection and type inspection B2 Factory inspection
B2.1 Factory inspection shall be carried out in accordance with the provisions of GB2828. Inspection items, unqualified classification, qualified quality level (AQI.) and inspection level (II.) are shown in Table Bl
Inspection items
Appearance quality
Open Door quality
Opening force
Plastic parts removal force
Tear-off force
Group batches with the same daily production.
B3 Type inspection
Jihen Paike 5 fins
Unqualified classification
17bzW.cn Crisp wall lotus
17jzw.com Crisp bear rate
He Helmet lotus jaw
He Iron Cui Partridge Boom
1 Jiying 60 meals
B3, 1 Type inspection should be carried out in the following cases: a) When new products are put into production or old products are transferred to other factories:
GE 5198.21996
When there is a major change in design, process or material; every six months during normal production;
When the production is suspended for more than six months;
When the national quality supervision agency proposes a requirement for type inspection. e
Type inspection shall be carried out according to the inspection items, non-conforming categories, non-conforming quality levels (RQI) and discrimination levels (DL) specified in GB 2829, see B2.
Inspection items
Machine performance
Appearance quality
Shoulder opening force
Plastic parts removal force
Sheet tearing force
Steam sterilization resistance
Compatibility
Opening quality
Coating semi-solidity
Unqualified classification
Appendix C
(Suggestive appendix)
Examples of chemical composition of aluminum alloys
Table C1 gives examples of the chemical composition range of aluminum alloys, expressed as a percentage of weight. Chemical composition examples
Content%(m/m）
0. 5 ~-0. 9
0. 5~1. 5
0.05~~0.20
0. 10-~ t. 5
Other elements: single
trace||5
GB 5198:2-1996
Table Cl(finished)
Content,%(m/m）
other lotus root
17bzw.cncrisp wall lotus root
17jzw.comcrisp bear throw
1Ji Ying 601 Mechanical properties
The mechanical properties (tensile strength and elongation) of aluminum parts should be in accordance with the provisions of GB228. Certificate 4: Bottle cap manufacturing! The mechanical properties test and chemical composition analysis report of the aluminum material supplier can be received. 7.2 Appearance quality
Visual inspection.
7.3 Dimensions
The inner diameter is inspected by limit gauge. Other dimensions are inspected by general measuring tools such as vernier calipers, height gauges and micrometers. 7.4 The convex edge defects of the four sides
The convex edge defects of the aluminum parts are calculated as a percentage, and the hue is calculated according to formula (1)
Where: hmax
The maximum height of the outer side of the bottle cap aluminum parts;
The minimum height of the outer side of the bottle cap aluminum parts.
Note: The surface drawing is enlarged to illustrate the maximum and minimum height of the outer side. Description of the convex edge of the wrong part of the bottle cap
7.5 Sterilization resistance, compatibility, strength
7. 5. 1 Steam sterilization process
Saturated steam treatment:
Heating time 30min;
Maintaining temperature 12]℃±2℃30min (including 130℃±2℃5min)); Cooling time 30min to 60℃
7.5.2 Capping process: Cover the antibiotic glass bottle that meets (B2G40 or GB2641 with the bottle stopper that meets YY0169.2, and add the bottle cap: Cap with the capping device
7.6 Coating firmness
Aluminum parts with coating on the outer surface: After going through 7.5.1 and removing the plastic parts, Immerse it in 80% (V/V) ethanol aqueous solution for 30 minutes, wipe the surface with absorbent cotton,
8 Marking, packaging
8.1 Marking
The packaging should have the following clear markings:
a) manufacturer's name;
b) product mark;
production batch number or date;
5
17bzw.cnCrisp Lotus Root
17jzw.comCrisp Bear Rate
He Yao Can Bian Lotus Root Color
Qing Tie Cui Pear
1 Ji Ying 60
GB 5198.2-1996
8.2 The packaging should ensure that there is no adverse effect on the performance of the bottle cap during transportation and storage and prevent any pollution. The inner packaging should be made of plastic bags. The outer packaging shall be in cartons or paper barrels that can withstand standard transport conditions. 187
A1 Equipment
GB5198.2---1996
Appendix A
(Standard Appendix)
Opening force test method
With Figures A1~A3 Special accessories as shown in the / compression testing machine, drive speed = 100rutn/tin, large range hand 1 (00N plastic part removal force
A2.1Z type and ZL) type bottle caps are shown in Figure A1.OB type and (L) type bottle caps are shown in Figure A2. Clamp the bottle caps on the special clamping screen and apply force to remove the plastic parts
Force application direction
Press rod size
Nominal size
Both traces Zhang Ke 5
ZB type and ZD type plastic part removal force testing device 17bzw.cn Crisp Bi Lotus
17izw.com Crisp Bear Rate
He Iron Cai Whip Lotus Color
With the type of iron friction
1 Ji Ying 60
Nominal size
GB 5198.2
Force direction
Degree
Figure A2 (Test device for removing force of type B and type OD plastic parts A2.2 Record the maximum force required to remove the plastic parts. A3 Tear-off force
As shown in Figure A3, the hook is hung on the exposed tear-off piece and the tension and compression testing machine is used to apply force in the direction shown in Figure A3 until the bottle cap is completely torn off. 189
Nominal size
GB 5198.2—1996
Force direction
Spindle size
Figure A3 Tear-off force test device
Appendix B
(Suggested appendix)
Inspection rules
B1 Product inspection is divided into factory inspection and type inspection B2 Factory inspection
B2.1 Factory inspection shall be carried out in accordance with the provisions of GB2828. Inspection items, unqualified classification, qualified quality level (AQI.) and inspection level (II.) are shown in Table Bl
Inspection items
Appearance quality
Open Door quality
Opening force
Plastic parts removal force
Tear-off force
Group batches with the same daily production.
B3 Type inspection
Jihen Paike 5 fins
Unqualified classification
17bzW.cn Crisp wall lotus
17jzw.com Crisp bear rate
He Helmet lotus jaw
He Iron Cui Partridge Boom
1 Jiying 60 meals
B3, 1 Type inspection should be carried out in the following cases: a) When new products are put into production or old products are transferred to other factories:
GE 5198.21996
When there is a major change in design, process or material; every six months during normal production;
When the production is suspended for more than six months;
When the national quality supervision agency proposes a requirement for type inspection. e
Type inspection shall be carried out according to the inspection items, non-conforming categories, non-conforming quality levels (RQI) and discrimination levels (DL) specified in GB 2829, see B2.
Inspection items
Machine performance
Appearance quality
Shoulder opening force
Plastic parts removal force
Sheet tearing force
Steam sterilization resistance
Compatibility
Opening quality
Coating semi-solidity
Unqualified classification
Appendix C
(Suggestive appendix)
Examples of chemical composition of aluminum alloys
Table C1 gives examples of the chemical composition range of aluminum alloys, expressed as a percentage of weight. Chemical composition examples
Content%(m/m）
0. 5 ~-0. 9
0. 5~1. 5
0.05~~0.20
0. 10-~ t. 5
Other elements: single
trace||5
GB 5198:2-1996
Table Cl(finished)
Content,%(m/m）
other lotus root
17bzw.cncrisp wall lotus root
17jzw.comcrisp bear throw
1Ji Ying 601 Mechanical properties
The mechanical properties (tensile strength and elongation) of aluminum parts should be in accordance with the provisions of GB228. Certificate 4: Bottle cap manufacturing! The mechanical properties test and chemical composition analysis report of the aluminum material supplier can be received. 7.2 Appearance quality
Visual inspection.
7.3 Dimensions
The inner diameter is inspected by limit gauge. Other dimensions are inspected by general measuring tools such as vernier calipers, height gauges and micrometers. 7.4 The convex edge defects of the four sides
The convex edge defects of the aluminum parts are calculated as a percentage, and the hue is calculated according to formula (1)
Where: hmax
The maximum height of the outer side of the bottle cap aluminum parts;
The minimum height of the outer side of the bottle cap aluminum parts.
Note: The surface drawing is enlarged to illustrate the maximum and minimum height of the outer side. Description of the convex edge of the wrong part of the bottle cap
7.5 Sterilization resistance, compatibility, strength
7. 5. 1 Steam sterilization process
Saturated steam treatment:
Heating time 30min;
Maintaining temperature 12]℃±2℃30min (including 130℃±2℃5min)); Cooling time 30min to 60℃
7.5.2 Capping process: Cover the antibiotic glass bottle that meets (B2G40 or GB2641 with the bottle stopper that meets YY0169.2, and add the bottle cap: Cap with the capping device
7.6 Coating firmness
Aluminum parts with coating on the outer surface: After going through 7.5.1 and removing the plastic parts, Immerse it in 80% (V/V) ethanol aqueous solution for 30 minutes, wipe the surface with absorbent cotton,
8 Marking, packaging
8.1 Marking wwW.bzxz.Net
The packaging should have the following clear markings:
a) manufacturer's name;
b) product mark;
production batch number or date;
5
17bzw.cnCrisp Lotus Root
17jzw.comCrisp Bear Rate
He Yao Can Bian Lotus Root Color
Qing Tie Cui Pear
1 Ji Ying 60
GB 5198.2-1996
8.2 The packaging should ensure that there is no adverse effect on the performance of the bottle cap during transportation and storage and prevent any pollution. The inner packaging should be made of plastic bags. The outer packaging shall be in cartons or paper barrels that can withstand standard transport conditions. 187
A1 Equipment
GB5198.2---1996
Appendix A
(Standard Appendix)
Opening force test method
With Figures A1~A3 Special accessories as shown in the / compression testing machine, drive speed = 100rutn/tin, large range hand 1 (00N plastic part removal force
A2.1Z type and ZL) type bottle caps are shown in Figure A1.OB type and (L) type bottle caps are shown in Figure A2. Clamp the bottle caps on the special clamping screen and apply force to remove the plastic parts
Force application direction
Press rod size
Nominal size
Both traces Zhang Ke 5
ZB type and ZD type plastic part removal force testing device 17bzw.cn Crisp Bi Lotus
17izw.com Crisp Bear Rate
He Iron Cai Whip Lotus Color
With the type of iron friction
1 Ji Ying 60
Nominal size
GB 5198.2
Force direction
Degree
Figure A2 (Test device for removing force of type B and type OD plastic parts A2.2 Record the maximum force required to remove the plastic parts. A3 Tear-off force
As shown in Figure A3, the hook is hung on the exposed tear-off piece and the tension and compression testing machine is used to apply force in the direction shown in Figure A3 until the bottle cap is completely torn off. 189
Nominal size
GB 5198.2—1996
Force direction
Spindle size
Figure A3 Tear-off force test device
Appendix B
(Suggested appendix)
Inspection rules
B1 Product inspection is divided into factory inspection and type inspection B2 Factory inspection
B2.1 Factory inspection shall be carried out in accordance with the provisions of GB2828. Inspection items, unqualified classification, qualified quality level (AQI.) and inspection level (II.) are shown in Table Bl
Inspection items
Appearance quality
Open Door quality
Opening force
Plastic parts removal force
Tear-off force
Group batches with the same daily production.
B3 Type inspection
Jihen Paike 5 fins
Unqualified classification
17bzW.cn Crisp wall lotus
17jzw.com Crisp bear rate
He Helmet lotus jaw
He Iron Cui Partridge Boom
1 Jiying 60 meals
B3, 1 Type inspection should be carried out in the following cases: a) When new products are put into production or old products are transferred to other factories:
GE 5198.21996
When there is a major change in design, process or material; every six months during normal production;
When the production is suspended for more than six months;
When the national quality supervision agency proposes a requirement for type inspection. e
Type inspection shall be carried out according to the inspection items, non-conforming categories, non-conforming quality levels (RQI) and discrimination levels (DL) specified in GB 2829, see B2.
Inspection items
Machine performance
Appearance quality
Shoulder opening force
Plastic parts removal force
Sheet tearing force
Steam sterilization resistance
Compatibility
Opening quality
Coating semi-solidity
Unqualified classification
Appendix C
(Suggestive appendix)
Examples of chemical composition of aluminum alloys
Table C1 gives examples of the chemical composition range of aluminum alloys, expressed as a percentage of weight. Chemical composition examples
Content%(m/m）
0. 5 ~-0. 9
0. 5~1. 5
0.05~~0.20
0. 10-~ t. 5
Other elements: single
trace||5
GB 5198:2-1996
Table Cl(finished)
Content,%(m/m）
other lotus root
17bzw.cncrisp wall lotus root
17jzw.comcrisp bear throw
1Ji Ying 602---1996
Appendix A
(Standard Appendix)
Opening force test method
With Figures A1~A3 Special accessories as shown in the / compression testing machine, drive speed = 100rutn/tin, large range hand 1 (00N plastic part removal force
A2.1Z type and ZL) type bottle caps are shown in Figure A1.OB type and (L) type bottle caps are shown in Figure A2. Clamp the bottle caps on the special clamping screen and apply force to remove the plastic parts
Force application direction
Press rod size
Nominal size
Both traces Zhang Ke 5
ZB type and ZD type plastic part removal force testing device 17bzw.cn Crisp Bi Lotus
17izw.com Crisp Bear Rate
He Iron Cai Whip Lotus Color
With the type of iron friction
1 Ji Ying 60
Nominal size
GB 5198.2
Force direction
Degree
Figure A2 (Test device for removing force of type B and type OD plastic parts A2.2 Record the maximum force required to remove the plastic parts. A3 Tear-off force
As shown in Figure A3, the hook is hung on the exposed tear-off piece and the tension and compression testing machine is used to apply force in the direction shown in Figure A3 until the bottle cap is completely torn off. 189
Nominal size
GB 5198.2—1996
Force direction
Spindle size
Figure A3 Tear-off force test device
Appendix B
(Suggested appendix)
Inspection rules
B1 Product inspection is divided into factory inspection and type inspection B2 Factory inspection
B2.1 Factory inspection shall be carried out in accordance with the provisions of GB2828. Inspection items, unqualified classification, qualified quality level (AQI.) and inspection level (II.) are shown in Table Bl
Inspection items
Appearance quality
Open Door quality
Opening force
Plastic parts removal force
Tear-off force
Group batches with the same daily production.
B3 Type inspection
Jihen Paike 5 fins
Unqualified classification
17bzW.cn Crisp wall lotus
17jzw.com Crisp bear rate
He Helmet lotus jaw
He Iron Cui Partridge Boom
1 Jiying 60 meals
B3, 1 Type inspection should be carried out in the following cases: a) When new products are put into production or old products are transferred to other factories:
GE 5198.21996
When there is a major change in design, process or material; every six months during normal production;
When the production is suspended for more than six months;
When the national quality supervision agency proposes a requirement for type inspection. e
Type inspection shall be carried out according to the inspection items, non-conforming categories, non-conforming quality levels (RQI) and discrimination levels (DL) specified in GB 2829, see B2.
Inspection items
Machine performance
Appearance quality
Shoulder opening force
Plastic parts removal force
Sheet tearing force
Steam sterilization resistance
Compatibility
Opening quality
Coating semi-solidity
Unqualified classification
Appendix C
(Suggestive appendix)
Examples of chemical composition of aluminum alloys
Table C1 gives examples of the chemical composition range of aluminum alloys, expressed as a percentage of weight. Chemical composition examples
Content%(m/m）
0. 5 ~-0. 9
0. 5~1. 5
0.05~~0.20
0. 10-~ t. 5
Other elements: single
trace||5
GB 5198:2-1996
Table Cl(finished)
Content,%(m/m）
other lotus root
17bzw.cncrisp wall lotus root
17jzw.comcrisp bear throw
1Ji Ying 602---1996
Appendix A
(Standard Appendix)
Opening force test method
With Figures A1~A3 Special accessories as shown in the / compression testing machine, drive speed = 100rutn/tin, large range hand 1 (00N plastic part removal force
A2.1Z type and ZL) type bottle caps are shown in Figure A1.OB type and (L) type bottle caps are shown in Figure A2. Clamp the bottle caps on the special clamping screen and apply force to remove the plastic parts
Force application direction
Press rod size
Nominal size
Both traces Zhang Ke 5
ZB type and ZD type plastic part removal force testing device 17bzw.cn Crisp Bi Lotus
17izw.com Crisp Bear Rate
He Iron Cai Whip Lotus Color
With the type of iron friction
1 Ji Ying 60
Nominal size
GB 5198.2
Force direction
Degree
Figure A2 (Test device for removing force of type B and type OD plastic parts A2.2 Record the maximum force required to remove the plastic parts. A3 Tear-off force
As shown in Figure A3, the hook is hung on the exposed tear-off piece and the tension and compression testing machine is used to apply force in the direction shown in Figure A3 until the bottle cap is completely torn off. 189
Nominal size
GB 5198.2—1996
Force direction
Spindle size
Figure A3 Tear-off force test device
Appendix B
(Suggested appendix)
Inspection rules
B1 Product inspection is divided into factory inspection and type inspection B2 Factory inspection
B2.1 Factory inspection shall be carried out in accordance with the provisions of GB2828. Inspection items, unqualified classification, qualified quality level (AQI.) and inspection level (II.) are shown in Table Bl
Inspection items
Appearance quality
Open Door quality
Opening force
Plastic parts removal force
Tear-off force
Group batches with the same daily production.
B3 Type inspection
Jihen Paike 5 fins
Unqualified classification
17bzW.cn Crisp wall lotus
17jzw.com Crisp bear rate
He Helmet lotus jaw
He Iron Cui Partridge Boom
1 Jiying 60 meals
B3, 1 Type inspection should be carried out in the following cases: a) When new products are put into production or old products are transferred to other factories:
GE 5198.21996
When there is a major change in design, process or material; every six months during normal production;
When the production is suspended for more than six months;
When the national quality supervision agency proposes a requirement for type inspection. e
Type inspection shall be carried out according to the inspection items, non-conforming categories, non-conforming quality levels (RQI) and discrimination levels (DL) specified in GB 2829, see B2.
Inspection items
Machine performance
Appearance quality
Shoulder opening force
Plastic parts removal force
Sheet tearing force
Steam sterilization resistance
Compatibility
Opening quality
Coating semi-solidity
Unqualified classification
Appendix C
(Suggestive appendix)
Examples of chemical composition of aluminum alloys
Table C1 gives examples of the chemical composition range of aluminum alloys, expressed as a percentage of weight. Chemical composition examples
Content%(m/m）
0. 5 ~-0. 9
0. 5~1. 5
0.05~~0.20
0. 10-~ t. 5
Other elements: single
trace||5
GB 5198:2-1996
Table Cl(finished)
Content,%(m/m）
other lotus root
17bzw.cncrisp wall lotus root
17jzw.comcrisp bear throw
1Ji Ying 60
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.