This standard specifies the types and interchangeability dimensions of lamp holders and starter holders for tubular fluorescent lamps (including H-shaped, ring-shaped and double-D types) with an operating voltage not exceeding 1000V. This standard applies to lamp holders and starter holders designed and manufactured in accordance with GB1312. GB 13260-1991 Types and dimensions of tubular fluorescent lamp holders and starter holders GB13260-1991 Standard download and decompression password: www.bzxz.net
Some standard content:
National Standard of the People's Republic of China Types and dimensions of lampholders for tubular fluorescent lamps and starterholdersGB13260—91 Replaces GB1312~77 This standard is equivalent Adopt the corresponding loose-leaf content in the international standard IEC61-2H (1987) "Lamp holders, lamp holders and gauges for testing their interchangeability and safety, Part 2 Lamp holders". 1 Subject content and scope of application This standard specifies the type and interaction of lamp holders and starter holders for tubular fluorescent lamps (including H-shaped, ring-shaped and double-D types) with an operating voltage not exceeding 1000V. Exchangeable size. This standard applies to lamp holders and starter holders designed and manufactured in accordance with GB1312. 2 Reference standards GB1312 Technical conditions for tubular fluorescent lamp lampholders and starter seats GB13261 Inspection gauge for tubular fluorescent lamp lampholders and starter seats 3 Lampholders and starter seats Inspection The lamp holders and starter holders in this standard are inspected separately using the gauges specified in GB13261. Types and dimensions 4 The types and dimensions of fluorescent lamp holders and starter holders are specified in Table 1. Table 1 Serial number 1 2 3 4 5 6 1 8 Terms 4.1 4.2 4.3 4.4 4.5 4.6|| tt||4.7 4.8 Inner G5 and G13 straight tube fluorescent lamp holders G5 and G13 rigid lampholders installed in pairs Capacity 2G13-56 and 2G13-92 U-shaped fluorescent lamp holder G10g ring fluorescent lamp holder Fa6 single-pin fluorescent lamp holder fluorescent lamp starter holder G23 single-ended Internal start fluorescent lamp holder (applicable to H lamp) GR8 fluorescent lamp holder (applicable to double D lamp) State Bureau of Technical Supervision 1991-10-29 approved drawing 1a, 1b 2 3 4 5 6 7 8 Table 2|| tt||3 6 8 1992-08-01 Implementation 4.1G5 and G13 straight tube fluorescent lamp holders This picture is only Indicates main dimensions. Female lamp holder GB13260—91 Flexible lamp holder c- Plug-in type Electric 6 D- b side-mounted (the lamp needs to be rotated 90°) rigid lamp holder Figure 1 Table 2 Dimension code 4| |tt||B C D E F G H 1||tt ||Min 15 5 7.35 2.8 3.2 3(M3) G5|| tt||maximum 2.5 15 5 3.5 minimum 38.5 5||tt| |7.35 2.8 3.2 3(M3) Note: The maximum and minimum size values ??not specified in the table must be designed to meet GB1312 Article 5.9 requirements for protection against electric shock. G13 20, 25, 30 13 mm Maximum 2.5 3.5 4.2 installed in pairs G5 and G13 Rigid Lamp Holder Points Tube Power w 4 6 8 12||tt| |13 15 Lamp holder G5 G13 GB13260—91 Figure 2 Table 3| |tt||The distance between the lamp holder surfaces A minimum value 136.0 212.2 288.4 485.1 517.0|| tt||437.6 Maximum 137.3 213.5 289.7 486.4 518.3 439.2||tt ||This picture only shows the necessary dimensions for 4.32G13-56 and 2G13-92U shaped fluorescent lamp holders. Hour Lamp head in love Lamp power W 20 30 40||tt| |65, 80 85 125 Picture 3 Lamp holder G13 E mm|| tt||Distance between lamp holder surfaces A Minimum value 590.0 894.0 1199.6 1500.2 1764.0||tt ||2375.1 Maximum 591.6 896.4 1201.2 1501.8 1765.6 2376.7||tt| |GB13260—91 The lamp holder is a combination of two separate G13 plug-in lamp holders. The dimensions of the individual G13 plug-in lamp holders are shown in Figure 1 and Table 2. The central axes of the two pairs of contacts should be in the same plane. . 2G13-56 2G13-92 A=56±0.1mm A=92±0.1mm 4.4G.10g ring fluorescent lamp holder||tt| |The center of the four pin holes The diameter of the concentric circles is approximately equal to 10 mm Female Every Lc Figure 4 Table 4 Size code A B c D E F Min. Value 6.17 7.75 3.1 7.77 4.5Fa6 Single Pin Tubular Fluorescent Lamp Holder This picture only shows the main dimensions . Maximum value 16.3 15.7 6.53 8.10 Size code K L M R minimum value 4.50 15.5 3.8 mm maximum value 2.6 11.6 Size code E G H Insulator Smooth surface | |tt | Table 5 | |tt | . 4.6 Starter base for fluorescent lamps Insulator BE Melting point U U Contacts on the side||tt| |Figure 6 T Contact at the end face Maximum value 6.08 mm Dimension code A B D E E H s minimum 12.5| |tt||21.7 5.4 8.7 16.2 Note: 1) Initial position of contact. 2) Contact open or depressed position. 4.7G23 single-ended internal start fluorescent lamp holder This picture only shows the main dimensions. ++ GB13260-91 Table 6 Maximum value 12.9 9.2 16.7||tt ||28.0 1.5 Picture 7 Size code T T T UP||tt ||U 8 Elastic retaining device\ Minimum value 2.5 2.3Www.bzxZ.net 18.0 45° mm Maximum value 1.5 17.0 Size code A B D E FP KP K minimum 32.6 18.2 22.9| |tt||2.9 6.9 16.4 15.85 14.0 GB13260—91 Table 7 Max. Value 23.1 2.6 16.55 16.0 14.15 Note: 1) This value is measured at 0.75mm from the datum plane . 2) This value is measured at 21.0mm from the reference plane. 3) This size is for design reference only and is not subject to inspection. Size code L M P R T Y n r 4) The elastic material shall comply with the requirements of Article 5.3.5 of GB1312 during the entire life of the lamp holder. Minimum 13.45 23.1 21.5 B/2 5.0 6.5 mm||tt| |Maximum 13.60 7.0 10.0 0.5 5) This contact is floating, and the electrical contact direction with the lamp head pin should be vertical on a plane passing through the centerline of the pin holes at both ends. Contact opening angle deviation ±30° 4.8GR8 double D-shaped fluorescent lamp holder Yunmen 1-1 Datum plane Shangshi bottle||tt| |Picture 8 aEnlarge Size code A B c D E||tt ||H K N P minimum 15.1 19.0 -||tt| |7.77 3.7 15.9 3.2 10.0 Note: 1) The size of the reed in the original position. 8.0 2) The offset size of the tongue when the lamp is fully inserted. Additional notes: GB13260-91 Table 8 Maximum value 20.1 28.5 - -| |tt||18.8 16.1 3.4 This standard is proposed by the Ministry of Light Industry of the People's Republic of China. This standard is under the jurisdiction of the National Electric Light Source Standardization Center. This standard is drafted by Beijing Electric Light Source Research Institute. The main drafter of this standard is Wang Yinquan. Size code R T Ta U V x Y| |tt||Minimum 9.1 21.7 - - - 0.9 0.7|| tt||0.9 30° mm Maximum 21.9 20.0 7.8 2.5|| tt||3.1 1.1 30° 4 This standard is proposed by the Ministry of Light Industry of the People's Republic of China. This standard is under the jurisdiction of the National Electric Light Source Standardization Center. This standard is drafted by Beijing Electric Light Source Research Institute. The main drafter of this standard is Wang Yinquan. Size code R T Ta U V x Y| |tt||Minimum 9.1 21.7 - - - 0.9 0.7|| tt||0.9 30° mm Maximum 21.9 20.0 7.8 2.5|| tt||3.1 1.1 30° 4 This standard is proposed by the Ministry of Light Industry of the People's Republic of China. This standard is under the jurisdiction of the National Electric Light Source Standardization Center. This standard is drafted by Beijing Electric Light Source Research Institute. The main drafter of this standard is Wang Yinquan. Size code R T Ta U V x Y| |tt||Minimum 9.1 21.7 - - - 0.9 0.7|| tt||0.9 30° mm Maximum 21.9 20.0 7.8 2.5|| tt||3.1 1.1 30° Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.