This standard specifies the technical requirements and test methods for inflatable toys. This standard applies to all types of inflatable toys made of high-frequency welding of polyvinyl film for non-water use. QB/T 2231-1996 General Technical Requirements for Inflatable Toys QB/T2231-1996 Standard download decompression password: www.bzxz.net

Industry Standard of the People's Republic of China
QR/T2231-1996
General Technical Conditions for Inflatable Toys
1996-07-05 Issued
China Light Industry Federation Issued
1996-12-[1 Implementation
Inflatable toys are made of our mouse's glory film. The winter series is a non-small shop. The quality is bright and colorful, and the product machines are complicated. Some of the internal rings are equipped with sounders. In the vast majority of inflatable toys, there are only a few types and products. In fact, there are only two types and products.
Long contact (1s/1.11993 (standard certification criteria No. 1: Drafting and expression period of standard reduction No. 1: Standard written by the sea = This standard is a system of 1--61 inflatable toys. The standard is in accordance with the standard of the China Light Industry General Association. Member of the standard department: This standard is issued by the National Standardization Center. This standard is compiled by the Shanghai Center for Standardization. The general draft cloud standard category changes cabinet Sa: In fact, the British help school, the five inspection crystal: xNrka
1 Scope
People's Republic of China Industry Standard
Inflatable General Technical Conditions for Toys
This standard specifies the technical requirements and test methods for inflatable toys. B/T2231-1996
This standard is used for various types of inflatable toys for non-water use that are made of high-frequency baked leather of ethylene oxide film. 2 Referenced Standards
The texts contained in the following standards constitute the provisions of this standard through reference in this standard. At the time of publication of the standard, the versions shown are valid. All standards are subject to revision. Before using this standard, all parties should consider using the latest version of the following standards.
GB667586 Toy Safety
3 Technical Requirements
3.1 Correct selection. 9 Particularly consistent with the standard. www.bzxz.net
3.2 The product can be in good condition. There is no leakage. 3.3 The product can be heat-sealed alone, with smooth surface and smooth edges. No shear-induced zigzag is allowed. 3.4 The gas spray of the inflatable device should have a one-way valve. The gas should be connected to the gas insulation, and the gas and gas sealing performance layers should be good. 4.3 There is no full air phenomenon after the test:
3.5 The connection of the gas plug shall not be broken when subjected to the working force. a. When the maximum contact size of the connection is less than 6mm, the force is 5V; b. When the maximum contact size of the connection is 5mm, the force is 50V. 36 Products with structural requirements should be stable, so the height of the product should not exceed m. There is no need to worry about the product experience. After testing, the product should not be noticeably dull: 3. For products with sound, the sound required by the product should be emitted; 3.8 The color matching should be harmonious, that is, the color matching should not be significantly different in a single product. 3.9 The content of harmful elements in the coating materials of the product should comply with the provisions of 13.2 of G36575~86; 3.10 The surface coating should be solid. After testing according to 4.6, there should be no obvious color change on the cloth; 3.11 After testing according to 47, there should be no obvious migration and sticking of the surface coating; 3.12 The printed pattern of the product should be clear, and there should be no obvious leakage of urine. The color matching of the main parts should be correct. China Light Industry Association 196-07-05 approved 1996-12-01 test bottle
Q5/ 2331-1996
3.13 For products that can be used in water, a permanent mark of "not to be used in water" shall be printed in an obvious position.
3.14 The packaging shall comply with the provisions of Chapter 5 of GR6675-86. 3.15 The surface of the product shall be clean and hygienic, and free from contamination. +Test method
4.1 The product shall be inflated to a proper amount of pressure, and then tested again at a temperature of 23=2°C. After the test is carried out at a high temperature of 42°C, the product shall be inflated to a proper amount of pressure, and then placed for more than 12 hours to check for moisture. 4.3 The product shall be inflated to a proper amount of pressure, and the pressure shall be inflated to the opposite direction, and then returned to the original pressure. This is one cycle. The test cycle shall be repeated 10 times at a frequency of 25, and then the product shall be checked to see if it meets the requirements of 3.4.
4.4 If the product is not in good condition, measure the force gauge at the connection between the valve and the gasket in the direction of the specified pull uniformly and maintain for 11 seconds to check whether the product meets the requirements of 2.5. 4.5 The product shall meet the requirements of Chapter 14 of 2005-86 for the material of the layer. 4.6 Place 500s carbon code on the wet weight of the self-made mat, and spread it on the surface of the product with a thickness of 3em/cm. The thickness shall meet the requirements of 3.10.
4. Take the sample belt as the center, take a 50mm long and 25mm wide film, fold it in half, pat the surface together, and use a piece of glass (2mm thick) to compact it. Put it on the top with a total load of 25 (including the cushion itself), and place it in a 602 refrigerator. After cooling, gently separate the layers and check if there is any color migration or pressure on the surface.
48 Stand the product on a horizontal table, observe the back of the product to see if it meets the requirements of 3.6. 4.9 Check the whole product: use your hand to move the air in the machine and listen to the sound. If the product meets the requirements of 3.
4.10 The size of the product should be checked to see if it meets the requirements of 3.6 to 3.14. 4.11 The appearance inspection should be carried out under normal light. The illumination should not be less than 5401x. The product is 2 lm away from the source and the viewing distance is 0.5m1. The product meets the requirements of 3.1, 3.3, 3.8, 3.12, 3.13 and 3.15. The heat seal is controversial. After the 4.2 test, it is inflated three times without air accumulation. KN
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.