This standard specifies the type, parameters, technical requirements, inspection rules and marking, packaging, transportation and storage of round and square hole sieve plates with a plate thickness equal to or greater than 3mm. This standard applies to sieve plates for screening with a plate thickness equal to or greater than 3mm and a basic size of sieve holes of 3.15mm to 125mm. GB/T 10613-2003 Industrial sieve plates Round and square hole sieve plates with a plate thickness of ≥3 mm GB/T10613-2003 Standard download decompression password: www.bzxz.net
This standard specifies the type, parameters, technical requirements, inspection rules and marking, packaging, transportation and storage of round and square hole sieve plates with a plate thickness equal to or greater than 3mm. This standard applies to sieve plates for screening with a plate thickness equal to or greater than 3mm and a basic size of sieve holes of 3.15mm to 125mm.

GB/T 10613-2003
This standard is modified to adopt ISO7805-1:1984 "Industrial sieve plates Part 1: Plate thickness ≥ 3mm" (English version). The main changes are as follows:
-ISO7805-1 gives the limit deviation of sieve holes and hole spacing in the form of formulas, and gives examples in the form of appendixes, while this standard directly gives the values ​​in the form of Tables 1 and 2, and gives the formulas for the limit deviation of sieve plate hole spacing and sieve hole size in the form of Appendix A. This standard replaces GB/T10613-1989 "Circular and square hole sieve plates with plate thickness ≥ 3mm". Compared with GB/T10613-1989, the main changes of this standard are as follows: Added provisions on materials;
- Modified some contents of marking and packaging, and added simple packaging methods. Appendix A of this standard is a normative appendix.
This standard was proposed by the China Machinery Industry Federation. This standard is under the jurisdiction of the National Technical Committee for Standardization of Screen Screening and Particle Sorting Methods (CSBTS/TC168). This standard was drafted by the Mechanical Science Research Institute, and Hunan Yueyang Wujiang Machine Screen Co., Ltd. participated in the drafting. The drafters of this standard are Wu Guochuan, Wan Jun, Sun An, and Yu Fang. This standard is interpreted by the Secretariat of the National Technical Committee for Standardization of Screen Screening and Particle Sorting Methods. The previous versions of the standards replaced by this standard are: -GB/T10613—1989.
1 Scope
Industrial sieve plates
Circular and square hole sieve plates with a plate thickness of ≥3mm
GB/T 10613—2003
This standard specifies the type, parameters, technical requirements, inspection rules and marking, packaging, transportation and storage of circular and square hole sieve plates with a plate thickness equal to and greater than 3mm.
This standard applies to sieve plates with a thickness equal to or greater than 3 mm and a basic size of sieve holes of 3.15 mm to 125 mm. 2 Normative references
The clauses in the following documents become clauses of this standard through reference in this standard. For dated references, all subsequent amendments (excluding errata) or revisions are not applicable to this standard. However, parties to an agreement based on this standard are encouraged to study whether the latest versions of these documents can be used. For undated references, the latest versions apply to this standard. Preferred numbers and preferred number systems
GB/T 321
GB/T 912
GB/T 1804
General tolerances for hot-rolled sheets and strips of carbon structural steel and low-alloy structural steelTolerances for linear and angular dimensions without tolerance indications (eqvISO2768-1:1989)Stainless steel cold-rolled sheets
GB/T 3280
GB/T 4879
GB/T7350
GB/T 10061
Rust-proof packaging
Waterproof packaging
Method for marking sieve holes (eqvISO7806:1983)Terminology for industrial sieves and screening (eqvISO9045:1990)GB/T 15602
3 Terms and definitions
The terms and definitions established in GB/T15602 and the following terms and definitions apply to this standard. 3.1
Margin
The distance between the edge of the sieve plate and the outer edge of the outermost row of holes. 3.2
Open area
The ratio of the total area of ​​the holes to the total area of ​​the open part of the plate. Expressed as a percentage. 4 Materials
This standard applies to sieve plates made of low carbon steel in GB/T912 and stainless steel in GB/T3280. Except for the size of the sieve holes, sieve plates made of other steel or non-metallic materials should be agreed upon by the supplier and the buyer. 5 Types and parameters
5.1 Arrangement of holes
The arrangement of holes shall comply with the provisions of GB/T10061. a) Round hole: T-type arrangement (see Figure 1);
b) Square hole: U-type arrangement (see Figure 2);
c) Square hole: Z-type arrangement (see Figure 3).
GB/T 10613—2003
Figure Round hole: T-type arrangement
5.2 Basic parameters and dimensions
Figure 3 Square hole: Z-type arrangement
Figure 2 Square hole U-type arrangement
5.2.1 The basic dimensions of the sieve holes are divided into the first series, the second series and the third series, and the first series is preferred. 5.2.2 The basic parameters and dimensions of the round hole sieve plate shall be in accordance with the provisions of Table 1. The basic parameters and dimensions not given can be calculated and corrected according to the formula in Appendix A.
5.2.3 The basic parameters and dimensions of the square hole sieve plate shall be in accordance with the provisions of Table 2. The basic parameters and dimensions not given can be calculated and corrected according to the formula in Appendix A.
5.2.4 The limit deviation of the length and width of the screen plate shall comply with the provisions of tolerance grade h14 in GB/T1804. If the user has special requirements, it shall be agreed upon by the supplier and the buyer.
First series
Basic dimensions
Second series
Table 1 Basic parameters and dimensions of round hole screen plates
Third series
Average value
Limit deviation
Basic dimensions
Limit deviation
GB/T 10613—2003
Unit: mm
Opening ratio
GB/T 106132003
Basic dimensions w
First series
Second series
Third series
Table 1 (continued)
Average value
Limit deviation
Basic dimensions
Limit deviation
Unit: mm
Opening ratio
First series
Basic dimensions
Second series
Third series
Table 1 (continued)
Average value
Limit deviation
Basic dimensions
Limit deviation
±1,00
GB/T 10613-—2003
Unit: mm
Opening ratio
GB/T 10613—2003
Basic size uWww.bzxZ.net
First series
Second series
Third series
Table 1 (continued)
Average value
Limit deviation
±1,40
Basic size
Limit deviation
Unit is mm
Opening ratio
First series
Basic size
Second series
Note 1: Opening ratio is a reference value
Third series
Table 1 (continued)
Average value
Limit deviation
Basic size
Note 2: The basic size of the hole spacing is allowed to be rounded according to the production and use requirements in accordance with GB/T321. Note 3: The basic size of the sieve hole in brackets can be selected in coal analysis. Hole
Limit deviation
Table 2 Basic parameters and dimensions of square hole sieve plate
Basic dimensions
First series
Second series
Third series
Average value
Limit deviation
Basic dimensions
GB/T 10613---2003
Unit: mm
Opening rate
Limit deviation
Unit: mm
Opening rate
GB/T 10613--2003
Basic dimensions
Serial number!
First series
Second series
Third series
Table 2 (continued)
Average value
Limit deviation
Basic size
Limit deviation
Unit: mm
Opening ratio
First series
Basic size
Second series
Third series
Table 2 (continued)
Average value
Limit deviation
Basic size
Limit deviation
GB/T 10613--2003
Unit: mm
Opening ratio
±0:50
GB/T 10613—2003
Basic dimensions w
First series
Second series
Third series
Table 2 (continued)
Average value
Limit deviation
±1,00
Basic dimensions
Limit deviation
±1,20
Unit is mm
Porosity
First series
Basic size
Second series
Note 1: Porosity is a reference value.
Third series
Table 2 (continued)
Average value
Limit deviation
Basic size
Note 2: The basic size of the hole spacing is allowed to be rounded according to the production and use requirements in accordance with GB/T321. Note 3: The basic size of the sieve hole in brackets is allowed to be selected in coal quality analysis. Hole
Limit deviation
GB/T 10613---2003
Unit is mm
Porosity
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.