Some standard content:
ICS 71.100.01;87.060.10
Chemical Industry Standard of the People's Republic of China
HG/T3677—2000
Sulfur Blue 4G (Sulfur Blue CV)
Sulphur Blue 4G (Sulphur Blue CV)2000-06-05Promulgated
Implementation on 2001-03-01
Promulgated by the State Administration of Petroleum and Chemical Industry
W Registration No.: 7497—2000
HG/T3677-—2000
This standard refers to the national standard GB/T2376—1980 "Determination of color and intensity of sulphur dyes". The test method for color and intensity is determined by selecting test conditions. At the same time, the inspection items and technical indicators are determined based on the product quality data provided by relevant manufacturers and on the basis of extensive consultation with manufacturers and users. The inspection of each item of this standard adopts the methods specified in the national standard. This standard is proposed by the Policy and Regulations Department of the State Administration of Petroleum and Chemical Industry. This standard is under the jurisdiction of the National Technical Committee on Standardization of Dyes. The drafting units of this standard are: Shenyang Chemical Research Institute, Baoding Shunfa Advanced Chemical Co., Ltd. The main drafters of this standard are: Ji Lanqin, Wang Junru, Zang Jianshe. This standard is interpreted by the Secretariat of the National Technical Committee on Standardization of Dyes. I
W.bzsoso.cOm1 Scope
Chemical Industry Standards of the People's Republic of China
Sulphur Blue 4G (Sulphur Blue CV)
Sulphur Blue 4G (Sulphur Blue CV) HG/T3677—2000
This standard specifies the requirements, sampling, test methods, inspection rules and marking, labeling, packaging, transportation and storage of Sulphur Blue 4G (Sulphur Blue CV, CI Sulphur Blue 15).
This standard applies to sulphur blue 4G, which is prepared by condensing p-aminophenol and mixed clevite and then sulphurizing and oxidizing with sodium polysulphide, and is mainly used for dyeing cotton textiles.
2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised, and parties using this standard should explore the possibility of using the latest version of the following standards. GB/T2374—1994 General conditions for dyeing determination GB/T2376—1980 Method for determination of color light and intensity of sulphur dyes 2381—1994 Method for determination of insoluble matter content in dyes GB/T2383—1980 Method for determination of sieve fineness of dyes GB/T2386—1980 Method for determination of moisture content in dyes and dye intermediates 3920—1997 Textiles Color fastness test Color fastness to rubbing (eqvISO105-x12:1993) 3921.4—1997 Textiles
3922—1995 Textiles
Color fastness test Color fastness to washing (eqvISO105-c04:1989) Color fastness test Color fastness to perspiration (eqvISO105-E04:1994) 4841.1—19841/1 Dyeing standard depth card GB/T
5713—1997
GB/T6152—1997
8427—1998
3 Requirements
Textiles
Textiles
Textiles
3.1 Appearance: blue-grey uniform powder.
3.2 Sulphur blue 4G shall meet the requirements of Table 1.
1. Strength, points
2. Color light
3. Content of impurities insoluble in sodium sulfide, %
Color fastness test Color fastness to water (eqvISO105-E01:1994)Color fastness test Color fastness to heat pressing (eqvISO105-X11:1994)Color fastness test Color fastness to light Xenon arc (eqvISO105-B02:1994)) Table 1
1 Quality requirements for sulphur blue 4G
is the standard 100
of the product is similar to the standard product ~ microbZxz.net
4 fineness (residue content through the 250μm sieve), %5 moisture content, %
Approved by the State Administration of Petroleum and Chemical Industry on June 5, 20005.0
Implementation on March 1, 2001
W.bzsoso: comHG/T3677-2000
3.3 The color fastness of sulphur blue 4G on cotton fabrics shall not be less than that specified in Table 2. Table 2 Color fastness of sulphur blue 4G on cotton fabrics Dyeing
Depth (xenon arc)
1/15~6
1)6% (oWf) is equivalent to 1/1 standard depth of dyeing. 4 Sampling
Sweat resistance
Friction resistance
Heat and pressure resistance
200℃
Discoloration 4h
Sampling is done in batches, and the manufacturer takes the products that are mixed evenly at one time as batches. The number of sampling barrels in each batch shall not be less than 10%, and the number of small batch products shall not be less than 3 barrels. The packaging of the products taken must be intact. When sampling, do not allow foreign impurities to fall into the products. Use a probe to take samples including the upper, middle and lower parts, and the sampling volume shall not be less than 200g. Mix the samples carefully and divide them into two clean, dry brown glass bottles with ground stoppers, and seal them with paraffin. Paste labels on the bottles. Note that the production bottles are kept for reference.
5 Test method
5.1 Determination of appearance
Visual determination is adopted.
5.2 Determination of dyeing shade and intensity
Name, product name, batch and sampling date. One bottle is used for inspection. The general conditions for dyeing shall be carried out in accordance with the relevant provisions of GB/T2374 and GB/T2376. 5.2.1 Dyeing depth and fabric treatment
The dyeing depth is stipulated as 3%, and 5g cotton yarn (or cotton cloth) is used for dyeing. Before dyeing, the weighed cotton yarn or cotton cloth is boiled for 10 minutes with 0.02g/L penetrant BX (industrial use) at a bath ratio of 1:20. After treatment, wash with clean water and squeeze out excess water for later use. 5.2.2 Preparation of dye bath
Weigh 1.5g of the test sample and standard sample (accurate to 0.0005g), mix with 15mL of 100g/L sodium sulfide (calculated as 100%) solution [dye: sodium sulfide (calculated as 100%) = 1:1] and 1mL of 50% Turkey red oil to make a slurry, add 50mL of distilled water, and then heat the dye solution to 90-95℃, keep it warm for 15min, and after it is completely dissolved, add 200mL of boiling distilled water, stir well, and transfer it into a 500mL volumetric flask after cooling, and dilute it to the scale with distilled water. The dye solution used for each dyeing must be prepared as it is used. In five 300mL dye vats, prepare the dye bath according to the provisions of Table 3. Table 3 Preparation of dye bath
Dyeing tank number
Standard solution with a concentration of 1.5g/500mL
Sample solution with a concentration of 1.5g/500mL
100g/L anhydrous sodium sulfate solution
50g/L anhydrous sodium carbonate solution
Add distilled water to
Bath ratio: cotton yarn (cotton cloth) is 1:40.
5.2.3 Dyeing operation
Wbzsoso.cOnHG/T3677—2000
After the dyeing solution is prepared, place the dyeing tank in a water bath to prepare for dyeing. The dyeing temperature is 30-40℃. Stir frequently when dyeing. Raise the temperature to 90-95℃ within 30min. Dye at this temperature for 30min. Take it out after dyeing and immediately put it into running water for full rinsing and oxidation. 5.2.4 Post-oxidation treatment
The dyed and washed samples are treated with 3g/L sodium perborate solution at a bath ratio of 1:20 at 50℃ for 15min, then washed with water and dried or air-dried at 60℃.
5.2.5 Evaluation of intensity and color
Perform in accordance with the relevant provisions of GB/T2374. 5.3 Determination of impurities insoluble in sodium sulfide shall be carried out in accordance with the relevant provisions of GB/T2381. 5.4 Determination of fineness
Perform in accordance with the provisions of GB/T2383. The standard sieve aperture used is 250μm. 5.5 Determination of moisture content
According to the "drying method" in GB/T2386-1980, dry at 100-105℃ for 4h. 5.6 Determination of color fastness on cotton fabrics
All color fastness test samples are dyed to 1/1 depth according to GB/T4841.1. The determination of color fastness to rubbing is carried out according to GB/T3920. The determination of color fastness to washing is carried out according to GB/T3921.4. The determination of color fastness to perspiration shall be carried out in accordance with the provisions of GB/T3922. The determination of color fastness to water shall be carried out in accordance with the provisions of GB/T5713. The determination of color fastness to hot pressing shall be carried out in accordance with the provisions of GB/T6152, 200℃ dry pressing (4h). The determination of color fastness to light shall be carried out in accordance with the provisions of GB/T8427. 6 Inspection rules
6.1 Inspection classification
In this standard, 3.1~3.3 are type inspection items, of which 3.1~3.2 are factory inspection items, and 3.3 is inspected once a year during continuous normal production.
6.2 Factory inspection
Sulfur blue 4G shall be inspected by the quality inspection department of the manufacturer in accordance with the requirements of this standard. The manufacturer shall ensure that all sulfur blue 4G products leaving the factory meet the requirements of this standard. 6.3 User Acceptance
The user has the right to inspect the received sulfide blue 4G in accordance with the provisions of this standard to check whether it meets the requirements of this standard.
6.4 Re-inspection
If one of the indicators in the inspection results does not meet the requirements of this standard, samples should be taken from twice the amount of packaging for re-inspection. If even one indicator does not meet the requirements of this standard as a result of the re-inspection, the entire batch of products cannot be accepted. 7 Marking, labeling, packaging, transportation and storage 7.1 Marking, labeling
The packaging barrels of sulfide blue 4G should be painted with firm and clear markings, indicating: manufacturer name, factory address, product name, registered trademark, standard number, batch number, production date, gross weight and net weight. Each package of the product should be attached with a label of a certain format, including: manufacturer name, product name, trademark, certificate that the product quality meets the requirements of the standard and standard number. 7.2 Packaging
Sulfur blue 4G is packaged in iron barrels lined with plastic bags and sealed. The net weight of each barrel is 25kg or 50kg. Each batch of packaged products should be accompanied by a quality certificate in a certain format. The certificate includes: manufacturer name, factory address, product name, batch number, production date, factory date, product net weight, proof that the product quality meets the requirements of this standard and the standard number. Other packaging can be negotiated with the user. 7.3 Transportation
Avoid strong vibrations during transportation, and be careful when handling. Prevent fire, sunlight and rain. Do not damage the packaging. 7.4 Storage
The product should be stored in a cool, dry and ventilated warehouse. 4
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.