title>JB/T 10141.1-1999 Wheel lathe accuracy inspection - JB/T 10141.1-1999 - Chinese standardNet - bzxz.net
Home > JB > JB/T 10141.1-1999 Wheel lathe accuracy inspection
JB/T 10141.1-1999 Wheel lathe accuracy inspection

Basic Information

Standard ID: JB/T 10141.1-1999

Standard Name: Wheel lathe accuracy inspection

Chinese Name: 车轮车床 精度检验

Standard category:Machinery Industry Standard (JB)

state:in force

Date of Release1999-10-08

Date of Implementation:2000-03-01

standard classification number

Standard ICS number:Mechanical Manufacturing>>Machine Tools>>25.080.10 Lathe

Standard Classification Number:Machinery>>Metal Cutting Machine Tools>>J53 Lathe

associated standards

Publication information

other information

Focal point unit:National Technical Committee for Metal Cutting Machine Tools Standardization

Publishing department:National Technical Committee for Metal Cutting Machine Tools Standardization

Introduction to standards:

JB/T 10141.1-1999 This standard is part of the JB/T 10141 "Wheel Lathe" series of standards. This series of standards includes the following two parts: JB/T 10141.1-1999 Wheel Lathe Precision Inspection JB/T 10141.2-1999 Wheel Lathe Technical Conditions This standard specifies the requirements and inspection methods for the geometric accuracy and working accuracy of wheel lathes. This standard is applicable to ordinary horizontal wheel lathes and gantry wheel lathes. CNC horizontal wheel lathes and gantry wheel lathes can be used as a reference. This standard was first issued on October 8, 1999. JB/T 10141.1-1999 Wheel Lathe Precision Inspection JB/T10141.1-1999 Standard Download Decompression Password: www.bzxz.net

Some standard content:

ICS 25. 080. 10
Machinery Industry Standard of the People's Republic of China
JB/T10141.1—1999
Wheel Lathe
Issued on 1999-10-08
Precision Inspection
Implementation on 2000-03-01
State Bureau of Machinery Industry
JB/T10141.1-1999
"Wheel Lathe Precision Inspection" There is currently no international standard or foreign advanced standard. This standard is formulated with reference to the precision inspection sheet of portal wheel lathes of advanced foreign wheel lathe manufacturers. This standard is a part of JB/T10141 "Wheel Lathe". This series of standards includes the following two parts: Part 1 (i.e. JB/T10141.1): Wheel Lathe Precision Inspection; Part 2 (i.e. JB/T10141.2): Wheel Lathe Technical Conditions. This standard is proposed and managed by the National Technical Committee for Metal Cutting Machine Tool Standardization. The responsible drafting unit of this standard: Qinghai Heavy Machine Tool Factory. The participating drafting unit of this standard: Qiqihar First Machine Tool Factory. The main drafters of this standard: Wang Shijun, Wang Qing, Jiang Zhaofang, Chen Wei, Dong Jingqi. 1 Scope
Machinery Industry Standards of the People's Republic of China
Wheel Lathe
Precision Inspection
This standard specifies the requirements and inspection methods for the geometric accuracy and working accuracy of wheel lathes. JB/T10141.1-1999
This standard applies to ordinary horizontal wheel lathes and portal wheel lathes. CNC horizontal wheel lathes and gantry wheel lathes can be used as references.
2 Referenced standards
The provisions contained in the following standards constitute the provisions of this standard through reference in this standard. When this standard is published, the versions shown are valid. All standards will be revised. The parties using this standard should explore the possibility of using the latest versions of the following standards. GB/T17421.1-1998 General Rules for Machine Tool Inspection Part 1: Geometric Accuracy of Machine Tools under No-load or Finishing Conditions 3 General Requirements
3.1 Refer to 3.1 in GB/T17421.1-1998 to adjust the installation level. Place a level gauge at both ends of the machine tool bed, and the readings of the level gauge in the longitudinal and transverse directions shall not exceed 0.06/1000.
3.2 Pre-adjustment inspection is only carried out during assembly, and no re-inspection is performed after the load test. 3.3 During inspection, the actual inspection order can generally be arranged according to the requirements of assembly and disassembly inspection tools, inspection convenience, and thermal inspection items. 3.4 When the precision test is carried out, the test piece shall be tested after finishing. 3.5 When the measured length is different from the length specified in this standard, the tolerance shall be converted according to the measurable length in accordance with the provisions of 2.3.1.1 of GB/T17421.1-1998. When the conversion result is less than 0.005mm, it shall still be calculated as 0.005mm. 3.6 The plane determined by the tool tip and the spindle axis is called the main plane; the plane passing through the spindle axis and perpendicular to the main plane is called the secondary plane. Approved by the State Bureau of Machinery Industry on October 8, 1999 and implemented on March 1, 2000
JB/T 10141.1 - 1999
Ittrt's
0001/S0'0bzxz.net
(Botai Weng
JB/T 10141.1 -- 1999
z1'9's
Device as a rack
800°9
JB/T 10141.1 -- 1999
081转
Device as a rack
zo'o'q
so'o'q
JB/T 10141.1 -
'081 Rotating King
Stepping Device
90'0°9
JB/T10141.1-1999
One Stroke'P
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.