JB/T 9005.9-1999 JB/T 9005.9-1999 Casting pulley for crane F type JB/T9005.9-1999 Standard download decompression password: www.bzxz.net
Some standard content:
JB/T 9005.9--- 1999 This standard adopts DIN15417:1982 "D-type wire rope pulley", DIN1850:1976 Part 1 "Bushing for wire rope pulley", IDIN15069:1977 "Isolator for wire rope pulley". This standard is a revision of ZB3J80006.9--87 "F-type cast pulley for crane". Only editorial changes were made to the original standard during the revision, and the main technical content did not change. This standard is part of the JB/T9005 series of standards "Cast pulleys for cranes", which includes the following 10 parts: JB/T 9005.1--1999 JB/T 9005.2--1999 JB/T 9005.3-1999 JB/T 9005.4--1999 JB/T 9005.5--1999 JB/T 9005.6-1999 JB/T 9005.7---1999 JB/T 9005.8:-1999 JB/T 9005.9- 1999 JB/T 9005.10—1999 Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane Cast pulley for crane This standard replaces ZBJ80006.9-87 from the date of implementation. Selection series and matching type of rope groove section , hub and bearing size Technical conditions This standard is proposed and assigned by the National Technical Committee for Standardization of Hoisting Machinery. The responsible drafting unit of this standard is Dalian Daqi Group Co., Ltd. The main drafters of this standard are Zhou Yu'an and Cui Zhenyuan. 447 1 Scope Machinery Industry Standard of the People's Republic of China Casting sheaves for cranes Type F- Casting sheaves for cranesJB/T9005.9--1999 Replaces ZBJ80006.987 This standard applies to cast wire rope sheaves with sliding bearings (hereinafter referred to as sheaves) within the scope of the movable sheave block of the crane. Sheaves specified in this standard can also be used in other sheaves in wire rope transmission, such as fixed sheaves or other load-bearing parts except the movable sheave block. 2 Types and dimensions 2.1 The types and dimensions of type F sheaves are detailed in Figure 1 and Table 1. Marking example: Wire rope diameter d = 25mm. Pulley diameter L) = 630mm and diameter D, = 90mm F-type pulley, marked as: Pulley F25X630-90 JB/T 9005.9-—1999B:/2 Approved by the State Machinery Industry Bureau on 1999-06-28 448 Figure 1 F-type 2000-01-01 implementation JB/T9005.9 To facilitate the installation of the pulley, the axial clearance rate of each side should be specified in the connection structure to be at least 1mm.2 According to design requirements, B size is allowed to change. 2.2 The dimensions of the bushing (T) for F-type pulleys are detailed in Figure 2 and Table 2. Marking example: Bushing (T) for F-type pulley with diameter D, = 90mm, marked as: JB/T 9005.9--1999 Bushing T90 Note: Lubrication grooves shall be opened as required. Figure 2 Bushing (T) JB/T9005.9--1999 Unit weight 2.3For the dimensions of the spacer ring (H) for F-type pulley, please refer to the provisions in Figure 3 and Table 3. Marking example: Diameter D,-90mm for F-type pulley spacer (H), marked as: S6 Spacer H90JB/T9005.9.-1999 Figure 3 Spacer (H) Unit weight JB/T9005.9—1999 Unit weight Note: S, the larger size in the dimension, is used when multiple pulleys are installed in parallel on the pulley shaft. DbzxZ.net Unit weight wall Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.