SJ/T 10220-1991 Key points for quality control of picture tube manufacturing (for black and white picture tubes) SJ/T10220-1991 standard download decompression password: www.bzxz.net
Some standard content:
Industry Standard of Electronic Industry of the People's Republic of China SJ/T ↑0220—91 Main Points for Quality Control of Picture Tube Manufacturing (Applicable to Black-and-White Picture Tubes) Issued on May 28, 1991 Implementation on December 7, 1991 by the Ministry of Machinery and Electronics Industry of the People's Republic of China Industry Standard of Electronic Industry of the People's Republic of China Main Points for Quality Control of Picture Tube Manufacturing (Applicable to Black-and-White Picture Tubes) 1 Main Content and Scope of Application SJ/T10220—91 This standard defines the main points and basic control methods for the manufacturing process of white picture tubes and is a supplement to the product technical specifications. This standard is not applicable to the production process of black-and-white picture components and is the basis for enterprises to formulate quality control documents for picture tubes. 2 Reference standards SJ/T10221 GB5960 GB5212 3 Basic control requirements General quality control guide for manufacturing of electric core components Black and white display blank detailed specification Black and white display test method 3.1 The main outsourced raw and auxiliary materials and parts supplier inspection and monitoring requirements shall be filled in according to the record A1. 3.2 The main outsourced raw and auxiliary materials and parts shall be graded by importance, and the factory inspection and acceptance of the main flow chart items shall be carried out according to the record A2. 3.3 The processes shall be classified by importance, and the quality control of the products shall be strictly monitored, and the specific requirements shall be filled in according to the record A3. For all the important processes of the chain process components, the process control points shall be established as needed, and the cost promotion and development of the four conditions shall be controlled. The system can be set up according to Appendix A4, and the characteristics of the woodworking products shall be systematically analyzed, and the causes of the quality problems shall be analyzed, and corresponding inspection control specifications shall be formulated according to the safety rate, and the responsible person shall be implemented. Appendix 44 can list 12 items, 3.4 should be carried out through sedimentation, coating, exhaust, time and other delivery parts to stop production, the equipment management department of the enterprise will ask the relevant department, according to the appendix, fill in the inspection requirements and issue them according to the unit, and record the equipment inspection quantity. If there are quantitative contents, the specific requirements should be recorded, and the equipment department should be assigned to the specific process supervision of the effectiveness of the inspection work. The equipment completion rate and powder point of the relevant coagulation process must be reviewed to reach 10%. 3.5 The relevant chain test bench for production line and product testing (including scanning instrument change \ according to Appendix A6) should be set up, and the system should be upgraded according to Appendix A7. 3.6 The minimum environment of the relevant processing area should be checked according to Appendix A. 3.7 The various types of analysis equipment should be planned and selected according to Appendix A. When the fire efficiency is present, the company should talk about the external folding. The analysis process should be analyzed twice. 3.e The product should be in accordance with the emergency port, content, method, and management according to the Ministry of Machinery and Electronics Industry of the People's Republic of China 1-1-28 Technical Standard 19511201 Real Bottle S11022091 Three! The relevant mistakes should be made. The personnel training of the personnel should be listed in Appendix A. 3 Shengda Appendix A11 Quality control record and product quality audit record card, open the limited collection and improvement work. 2 SJ/T1022091 Black and white display manufacturing quality control content and implementation (supplementary cattle> A1 Main outsourcing, outsourcing raw and auxiliary materials and parts supplier list and monitoring requirements This document requires outsourcing, special outsourcing materials and departmental nominal driving Heater (natural hair Acid-free tough glass array Fluorescent clinical White analysis membrane Air-drying agent E-book Water-soluble external Ningshi type hole Certification or certification unit Supervision site SJ/T 10220 YEEF AS 699 HE Test type and efficiency lertao Heavy property Cathode silk moving time system Bright cavity to inquire! Protection limit Upload peripherals External conduction voltage rent Medical suction self-time wind Including red series Meishi average 1 sequence name SF/T 10220-91 Study Engineering More Home Source No F Industry Market Division External Electrical Products Electric Box Creative Such as Time Work Warehouse Name Powder To Gaozheng SJ/T10220-91 Recovery Quantity Standard Joint Industry Issuer Recovery Card Group Recovery Copper According to External Conductor Lips and Boundaries Inspection of Skin Scanning Full Supply Meaningless Function Test Court Heat Resistance A5 Inspection requirements for production equipment for production equipment Equipment name Inspection items Calibration requirements for chain test Chain test Equipment name Accuracy S/10220—91 Item index Calibration period Inspection instrument Instrument method Accuracy standard | |tt||Check and purchase The standard is approved by the person who has obtained the mark Please indicate the period of quick exploration and record length with no number to indicate that the month is "\net system use as *, no fixed use as-with system use sound points should be introduced in the ticket companion to explain the reason for the damage report, no guarantee of the use of the equipment in the test space in the equipment in the towel Ma clearly explained the situation of the promotion. The processing area environment is required The name of the warehouse is calculated The real section is exploded B failure points are used by the designer Analysis equipment Quality requirements Authorized process Change process||tt ||Diameter and perimeter planning Calibration process Teaching standard Test sensitivity Ancestor, display meter, Dust increase calibration shop Test equipment , hygrometer, Modern environment control, Test equipment Quick procedure 1 girl/class 1 class Standard Attached test personnel Record the most important table : Special record scale Special society According to the standard personnel SJ/T 10220-- 97 S-9-Tov s-1-10v 61*中 01\ 中 Drive light some SJ/T 10220—97 以丫道前 1-3g m*21-d OH9-N9-g {-8-rs-J s 9-TOY ★*鼻屏 EI'中 16869 2 中 - 10 - A10 Requirements for training and adjustment of special work personnel (personnel name you testing and inspection related, direct change process machine SJ/T 1022091 training summary 1 process sequence operation procedures 2 process adjustment and development procedures 3 safety and slow operation procedures work management knowledge and quality state requirements management statistics 5 Basic technical foundation of products 6 Electrical knowledge Machinery knowledge 8 Basic characteristics, functions and features of mechanical equipment 9 Knowledge acquired through on-the-job training 1 General process operation specifications 2 Product inspection technology Complete operation procedures 4 Process management and quality control commonly used mathematical formulasbzxZ.net 5 Basic technical foundation of products 6 Comprehensive knowledge 7 Knowledge acquired through on-the-job training 【Process operation cabinet 31\Process regulation 3 Safety operation specifications :0.5--1 month 0.5~-0.6 month 4 Process knowledge and quality control with mathematical design methods 5 Basic technical foundation of products Other job training knowledge Training photos Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.