Some standard content:
ICS61.060
Chemical Industry Standard of the People's Republic of China
Sports shoes, rain boots (shoes)
(2001)
Published on 2002-01-24
Implemented on 2002-07-01
Published by the State Economic and Trade Commission
Ticket number: 10147-2002
[IG/T2019 —2001
This standard is not equivalent to the Japanese T industry standard JISS5005-1992 and the T/T2019—1991 (shoes). The main technical differences between this standard and J1555005-:992 are: the deformation, resistance, heating loss (%), acid cracking intensity, dyeing fastness and other performance measures in the Japanese wood industry standard are adopted.
Specific descriptions are made on the appearance.
The main technical differences between this standard and HG/2019—1991 are that the physical performance has added the frequency of pulling and the aging performance retention rate as the type inspection items, and the water performance test requirements for the upper leather and outer sole thickness of rubber boots (shoes) have been added. The external quality inspection standard is appropriately modified.
This standard replaces HG/19-1991 standard of the State Petroleum and Chemical Industry Administration from the date of implementation. This standard is under the jurisdiction of the National Rubber and Rubber Products Standardization Technical Committee Rubber Shoes Technical Committee. The responsible drafting unit of this standard: Jiangning Shenfu Rubber Factory The drafters of this standard are Hao Zengmao, Xie Hua, Chen Shi, Ding Yuchan. This standard was first issued in June 1991.
Chemical Industry Standard of the People's Republic of China
Black rain boots (shoes)
Black rain rubber buots [shoes] G/T2019—2001
Replaces HG: T20191991
This standard specifies the requirements, test methods, inspection rules, marking, packaging, transportation and storage of black rain boots (shoes). This standard applies to black rain boots made of black material or general waterproof wear boots (). This standard does not apply to acid-resistant, heat-resistant, insulating, industrial expansion and special compression rubber surfaces (groups). 2 Referenced standards
The texts contained in the following standards are all recorded in this standard through reference in this standard. When this standard is published, the versions shown are valid and all the standards will be revised. All parties using the standards should explore the possibility of using the latest version of the following standards. GB/T528—1993 Determination of tensile strain properties of synthetic rubber or thermoplastic rubber (eqVIS) 3? .1794) GB/T53:-1999 Rubber extraction hardness test with hardness meter (ISO 7619:1986) GB/T532-1997 Determination of adhesion and compression strength of chemically treated or thermoplastic rubber to fabric (ISO 36:1993)) 1998 Determination of abrasive properties of chemically treated rubber (using abrasive wear tester) GB/T1589 GB/T2941-1D91 Rubber test specimen environmental conditions and standard temperature, humidity and time for testing (ISO 471:1S8S) GB/3293.-1998 (ISO 9407-1991) )
GB/TA293—1982 China shoe size and inspection series GBT35121983(1989) Rubber hot air rolling test method (NE9IS0188:1576) HG/12198
General requirements for physical test methods for aging-resistant rubber shoes Inspection regulations for marking, packaging, transportation and storage HG/T2403—1992
HG/T3664—2000
3 Definition
Water splashing test method for surface adhesive ES2023159)
This standard uses the following definitions:
Base thickener
Base thickness of the outsole after deducting the flower pattern. 4 Classification
4.1 High semi-rain boots
Refers to rubber boots with a height greater than or equal to 220 mm. 4.2 Light rain boots
Refers to rubber boots with a height of less than 20 mm and a height of more than 125 mm (including 25 mm). 4.3 Rain boots
Refers to rubber boots with a height of less than 125 mm.
Approved by the State Economic and Trade Commission on January 24, 2002 and implemented on July 1, 2002
5. 1 、Model
HG:T2019—2001
Domestic sales products H silicon number, type, shoe size, block technology GBT32S3 and GBT3293.1 regulations export products its group number model production Meng Zhengcun Xie Kang selected 5.2 physical mechanical properties
Physical and mechanical properties shall comply with the provisions of Table 1 and Table 2: Table 1 Physical mechanical performance requirements (for numbers above 195,) Item
Tensile strength, MP
Elongation,
Width, A degree
Adhesion strength.kN/ar
Elongation, 3
Aging performance (70±1>1.×72Standard strength retention rate,%11.B
c.Social u, 4
Table 2 Mechanical performance requirements and (below 105 and including 105)
Tensile strength, MI\s
Elongation at break, %
Quick store·Jianle
Adhesion strength, kN/m
Bonding elongation, %
Aging resistance (70+1 yuan 2 Tensile strength retention rate, %25.3 Outer center thickness
Outer sole thickness should be light and suitable for 3 specifications,
Table? Outer rib thickness requirements
Dimensions (middle code S)
Outer sole properties
Rate, rm
B plate rate.ma
Back center thickness·mm
Guaya store
Government store
Note: The front, the thickest part of the piece includes the thickness of the convex part, 5. 4 Thickness of the batch surface
The floating degree of the boot surface should be greater than or equal to ".! \. 5.5 Water-resistant
The rubber should be guaranteed to have water and water phenomena 12
5s:230
Luzi bottom
Moulded azole
5.6 Appearance quality
The appearance quality should meet the requirements of Table 4,
China Real Estate
Melting sink name
Viscose fast epidemic environment
Surface fiber
Upper rubber external technology | |tt||No guest to rely on
Uneven evaluation of oil and water beside
Filling the yang to take the mood
Kill the oil color strip
Drawing the (Gui) treasure shell
Opening
Filling the oil leakage system
Ningnei Courtyard Shelling
Positive and oblique stock space
Xu Luo Shanting Qi Pool
Gao Mei Bu Wen
With the outer bottom to take off the filling
With the outer bottom to bounce
New side Qi flower
Change the front installation and the rear thick positive nest
T 2019—2001
Table 1 Appearance measurement
Slightly missing mosquitoes and veins, not close to the eye
No bending allowed: other parts are no more than . 5mm
(needle front six in the same, the local surface is not more than 5mm: outside the high half of the two places
No bending allowed, the part point diameter is less than 1. 5m, suction, high half limit four
Can not be eliminated, the area of the industry is not twisted more than 25mT.1, limited to one place, high half limit two
No glue is allowed, the opposite side will be damaged. The depth is not more than 1mm. Limited to one place, the joint thickness is not more than 2. E usu
storage will not have, other parts of the letter to the accumulation of cabinets not over the use of "limit
positive drop outside 1
1u blunt eat.X consumption display uneven
() with no other ministers 15
the following risk a let surface not more than
[mn, high blue system estimate
no line lead
noodle machine not more than 150mm, attached one place, the system does not have (through the mold buried according to the technology in this limit)
ban count noodle machine not reported more than 300mm
show business has
system mouth 1/7 medical small
more than 2 not more than
juice noodle machine not bottle 300mm
to calculate blood can not afford more than 45: mm
high or 2mm,The limit is three
surface original wish is more than 2mmmm, the limit is two
mineralization and external elasticity are not more than
diameter is less than 1502, the limit is four (the limit is after the first time
light efficiency unknown pump
when the actual is not more than mmz
joint bearing and the outer bed can not rise again 2 n1
qualified products
do not produce over-shadow
no place under the full, the total position diameter does not exceed 1.5 mm, the limit is half continuous limit, the limit is not allowed to make a single lower
place, he passes
joint (shoe> front three area card more than 25 mm, attached whole, or its circulation area is not more than 50T danger
one, the high system
ancient diameter does not exceed 2. 5 , two places, high half except limited jade
long piece does not exceed mm, use two places, high half age insurance four places
stock rubber length waste does not exceed 10 Work Hm, temporary error is not 2, hot space size is not twisted, the number of drawing is not more than 2, other parts are afraid of not seriously affecting the situation, 1m distance, average length of the pin is less than 25mns, electric two places, or the limit is not more than 5mm for the first standard, high system such as not to produce real shadow related knowledge, not seriously affecting the view, is the design surface sail does not exceed but not apply to the system outlet, not to wear ... From the north, the outer height is not allowed to go down more than 00
The height is not more than the limit
The device plan is not more than" m
The chemical and outer bank detection are not
The straight line is not more than 2mm. The eight places
No ghosting is used. The depth is not more than mm
Low eleven grade product regulations
Defect name
Particle impurity gas inquiry
Courtesy low
Second reach pore
Outer room aftertaste flower effect length
Washing mouth low uneven
G/12019--2001
Table 4 (end) External mixed quality company
Curve is not careful, other position diameter is not allowed 2 mm, limited to one place, can not afford to be too thick -/3 Li area does not exceed 1mm, version · place, flower level to this clear
diameter does not exceed 1.m limit
(difference does not exceed
195 below the light distance does not exceed 5mm
double can change the upper mouth of the height difference does not exceed 6
category does not exceed 4mm
Taiwan birch products
check the establishment of the place is not controlled, other details make the straight light does not exceed 1ur limit one, the depth does not exceed 1/3 of the single
surface does not exceed 40gmm, can - place, flower effect is this elimination bottom
diameter does not exceed the limit
the same 14, shoes
135 below the amount does not exceed 5mm
the same effect class capital on the outside of the low does not exceed m
Gui does not exceed 5 mm
Not allowed to store
Note: The anti-allergic items not listed in the above table shall be handled according to the above table: "The products with serious impact on the current case shall be considered unqualified. 6 Test methods
6.1 General requirements for the test method for physical and mechanical properties of slow adhesives shall be implemented in accordance with the provisions of HG/T2198: The finished product sample can be cut along the bottom direction.
6.2 Standard temperature, humidity and time for rubber specimen placement and testing The standard temperature, humidity and time for rubber specimen placement and testing shall be in accordance with the provisions of T391. The placement time before the test shall not be less than that of rubber specimens.
6.3 Determination of elastic tensile properties of rubber
The determination of the tensile properties of vulcanized roll-to-roll properties shall be in accordance with the provisions of GH/528. The surface and outsole can be tested using 60T. When the test thickness does not reach the test standard, the test shall be based on the actual thickness of the specimen. 6.4 Determination of the wear resistance of calcined rubber
The wear resistance of calcined rubber shall be determined according to the provisions of H/T189. When the test piece is not long enough, it can be slowed down in the direction of the outer sole. When the original thickness of the sample does not reach the test force method standard, the sample thickness test shall be carried out. 6.5 Rubber expansion test
Rubber hardness test shall be carried out according to the provisions of H/T531. If the test thickness does not meet the requirements, multiple layers can be added until the test requirements are met. ||t t||6.6 Adhesion strength test
Adhesion resistance strength test According to the environment of T532, take the test rod and take the film: take two waists, about longitudinal on both sides of the makeup, take: a test rod, effective width is 1C, length 100--150mm, use a small sample to increase the effective width of the cloth and the opening, from the grid test support system vertically 40--50 length (that is, the effective length of the sample), 6.7 Continuous film elongation testbZxz.net
6.7. 1 Test piece
Cut a piece with a length of 120~125mm, a width of (10±0.2)mm, and the thickness of the original finished product, and mark the test piece with two marks with a spacing of (100-0.5)um.
6.7.2 Test step
After the test piece is fully stretched, place the test piece under the test piece at a speed of (100±i)mm/ia. When the test piece is stretched to the point where the paint film appears and the first bag appears, the test piece is stretched to the point where the paint film appears. 6.7.3 The result indicates that the film length is the length of the sieve according to the sieve.
In the formula, the distance from the original mark of the test piece to the original mark is about 1/2 of the distance from the original mark of the test piece to the original mark. HG/T 2019 2001
I. When a crack appears on the film, the distance between the test piece cup lines is m: Two test pieces are made for each pair of shoes, and the average value is taken. 6.8 The overall chemical test is carried out according to the provisions of B512. The aging test conditions are 70°C × 72°C. After aging, the sample is placed for 424 hours and then the tensile strength is measured. It is compared with the unaged test piece to calculate the tensile strength retention rate (%) of the tensile aging performance. The tensile strength retention rate (%) of the tensile aging performance is calculated according to (2): p
Where: A
Aging time of the sample, MPa; C Tensile amplitude of the sample before aging, MPa.
The value of aging energy retention rate (Xing) shall be accurate to 6.9 Determination of thickness
6.9.1 Determination of outer sole thickness
Retract the outer sole at the test point, cut off the outer sole edge, and leave the midsole and center core to obtain the boot sole. Determine along the center axis of the rubber sheet of the sole, use a vernier caliper to measure the thickness of the front palm force point, the back palm force point and the thickness of the bottom plate respectively, and take the maximum value of the obtained data, retaining one decimal place. 6.9.2 Determination of thickness
Cut the surface with the test piece, and separate it. When the film is obtained, use a rubber measuring device to measure the surface thickness, and take the minimum value, and retain one decimal place.
6.10 Test
The water resistance test shall be carried out in accordance with the provisions of HG/T3E64. 7 Inspection rules, marking, packaging, transportation and storage. Marking, packaging, transportation and storage shall be in accordance with the relevant provisions of HG/T2403 for the batch (shoes). The inspection of the outer thickness shall be in accordance with 3.2.1.2 of HG/T2403-7992. The aging test and micro-bearing test shall be in accordance with 3.3 of HG/T2403-1992. At the same time, the standard number 16 shall be marked on the packaging of each pair of (shoes).The error degree of temporary damage is not more than 2, the size of the heat space is not twisted, the number of drawings does not exceed 20, other parts are afraid that the relevant conditions will not be seriously affected by 1m distance, the average length of the sales is less than 25mns, the electrical second place, or the limit of the original rent is not more than 5mm for the first standard. The high system such as does not produce real shadow related knowledge, does not seriously affect the view, is the design surface does not exceed but does not apply to the system outlet, does not affect the wearing, smooth surface, but C, this standard has no more shadow, does not produce more shadow, the design surface cannot exceed C0, the distance is too far. North, the outer height is not allowed to drop more than 00
The height is not more than the limit
The device plan is not more than" m
The chemical and outer bank detection are not
The straight line is not more than 2mm. The eight places
Do not produce ghosting conditions
The depth is not more than mm
Low eleven grade product regulations
Defect name
Particle impurity gas inquiry
Courtesy low
Second reach pore
Outer room aftertaste flower effect length
Washing mouth low uneven
G/12019--2001
Table 4 (end) External mixed quality company
Curve is not careful, other position diameter is not allowed 2 mm, limited to one place, can not afford to be too thick -/3 Li area does not exceed 1mm, version, flower level to this clear
diameter does not exceed 1.m limit
(difference but
195 below the light distance does not exceed 5mm
double can change the upper mouth of the height difference does not exceed 6
category does not exceed 4mm
Taiwan birch products
check the establishment of the system, other details make the straight light does not exceed 1ur limit one, the depth does not exceed 1/3 of the single
surface does not exceed 40gmm, can - place, flower effect is this elimination bottom
diameter does not exceed the limit
the same 14, shoes
135 below the amount does not exceed 5mm
the same effect class capital on the outside of the low does not exceed m
Gui does not exceed 5 mm
Not allowed to store
Note: The anti-allergic items not listed in the above table are handled according to the above table: "The important items should be considered as unqualified products. 6 Test methods
6.1 General requirements of the test methods for the physical and mechanical properties of slow glue. The general requirements of the test methods for the physical and mechanical properties of slow glue shall be implemented according to the provisions of HG/T2198: The finished product samples can be cut along the bottom direction.
6.2 Order of the test samples The standard temperature, humidity and time of the test for the rubber specimens shall be placed and tested in accordance with the provisions of T391. The placement time before the test shall not be less than that of the test specimens.
6.3 Determination of tensile properties of elastic resins
The determination of the vulcanized rolling tensile properties shall be carried out in accordance with the provisions of GH/528, among which the surface and the outsole can be tested using 60T. When the test thickness does not reach the test standard, the test shall be carried out according to the actual standard thickness of the specimen. 6.4 Determination of the wear resistance of calcined rubber
The wear resistance of calcined rubber shall be determined according to the provisions of H/T189. When the test piece is not long enough, it can be slowed down in the direction of the outer sole. When the original thickness of the sample does not reach the test force method standard, the sample thickness test shall be carried out. 6.5 Rubber expansion test
Rubber hardness test shall be carried out according to the provisions of H/T531. If the test thickness does not meet the requirements, multiple layers can be added until the test requirements are met. ||t t||6.6 Adhesion strength test
Adhesion resistance strength test According to the environment of T532, take the test rod and take the film: take two waists, about longitudinal on both sides of the makeup, take: a test rod, effective width is 1C, length 100--150mm, use a small sample to increase the effective width of the cloth and the opening, from the grid test support system vertically 40--50 length (that is, the effective length of the sample), 6.7 Continuous film elongation test
6.7. 1 Test piece
Cut a piece with a length of 120~125mm, a width of (10±0.2)mm, and the thickness of the original finished product, and mark the test piece with two marks with a spacing of (100-0.5)um.
6.7.2 Test step
After the test piece is fully stretched, place the test piece under the test piece at a speed of (100±i)mm/ia. When the test piece is stretched to the point where the paint film appears and the first bag appears, the test piece is stretched to the point where the paint film appears. 6.7.3 The result indicates that the film length is the length of the sieve according to the sieve.
In the formula, the distance from the original mark of the test piece to the original mark is about 1/2 of the distance from the original mark of the test piece to the original mark. HG/T 2019 2001
I. When a crack appears on the film, the distance between the test piece cup lines is m: Two test pieces are made for each pair of shoes, and the average value is taken. 6.8 The overall chemical test is carried out according to the provisions of B512. The aging test conditions are 70°C × 72°C. After aging, the sample is placed for 424 hours and then the tensile strength is measured. It is compared with the unaged test piece to calculate the tensile strength retention rate (%) of the tensile aging performance. The tensile strength retention rate (%) of the tensile aging performance is calculated according to (2): p
Where: A
Aging time of the sample, MPa; C Tensile amplitude of the sample before aging, MPa.
The value of aging energy retention rate (Xing) shall be accurate to 6.9 Determination of thickness
6.9.1 Determination of outer sole thickness
Retract the outer sole at the test point, cut off the outer sole edge, and leave the midsole and center core to obtain the boot sole. Determine along the center axis of the rubber sheet of the sole, use a vernier caliper to measure the thickness of the front palm force point, the back palm force point and the thickness of the bottom plate respectively, and take the maximum value of the obtained data, retaining one decimal place. 6.9.2 Determination of thickness
Cut the surface with the test piece, and separate it. When the film is obtained, use a rubber measuring device to measure the surface thickness, and take the minimum value, and retain one decimal place.
6.10 Test
The water resistance test shall be carried out in accordance with the provisions of HG/T3E64. 7 Inspection rules, marking, packaging, transportation and storage. Marking, packaging, transportation and storage shall be in accordance with the relevant provisions of HG/T2403 for shoes. The inspection of the outer thickness shall be in accordance with 3.2.1.2 of HG/T2403-7992. The aging test and micro-bearing test shall be in accordance with 3.3 of HG/T2403-1992. At the same time, the standard number 16 shall be marked on the packaging of each pair of shoes.The error degree of temporary damage is not more than 2, the size of the heat space is not twisted, the number of drawings does not exceed 20, other parts are afraid that the relevant conditions will not be seriously affected by 1m distance, the average length of the sales is less than 25mns, the electrical second place, or the limit of the original rent is not more than 5mm for the first standard. The high system such as does not produce real shadow related knowledge does not seriously affect the view of the relevant surface. The sail does not exceed but does not apply to the system outlet. The wear of the smooth surface is not more than C. The standard has no more shadow on the light version. The surface cannot exceed C0. The distance between the practice of intelligent characters is too far. North, the outer height is not allowed to drop more than 00
The height is not more than the limit
The device plan is not more than" m
The chemical and outer bank detection are not
The straightness is not more than 2mm. The eight places
No ghosting is used. The depth is not more than mm
Low eleven grade product regulations
Defect name
Particle impurity gas inquiry
Courtesy low
Second reach pore
Outer room aftertaste flower effect length
Washing mouth low uneven
G/12019--2001
Table 4 (end) External mixed quality company
Curve is not careful, other position diameter is not allowed 2 mm, limited to one place, can not afford to be too thick -/3 Li area does not exceed 1mm, version, flower level to this clear
diameter does not exceed 1.m limit
(difference but
195 below the light distance does not exceed 5mm
double can change the upper mouth of the height difference does not exceed 6
category does not exceed 4mm
Taiwan birch products
check the establishment of the system, other details make the straight light does not exceed 1ur limit one, the depth does not exceed 1/3 of the single
surface does not exceed 40gmm, can - place, flower effect is this elimination bottom
diameter does not exceed the limit
the same 14, shoes
135 below the amount does not exceed 5mm
the same effect class capital on the outside of the low does not exceed m
Gui does not exceed 5 mm
Not allowed to store
Note: The anti-allergic items not listed in the above table shall be handled according to the above table: "The items that are important to the current case shall be considered unqualified. 6 Test methods
6.1 General requirements for the test methods of physical and mechanical properties of slow glue. The general requirements for the physical and mechanical properties of slow glue shall be implemented according to the provisions of HG/T2198: The finished product samples can be cut along the bottom direction.
6.2 Order of rubber samples The standard temperature, humidity and time of the test for the rubber specimens shall be placed and tested in accordance with the provisions of T391. The placement time before the test shall not be less than that of the test specimens.
6.3 Determination of tensile properties of elastic resins
The determination of the vulcanized rolling tensile properties shall be carried out in accordance with the provisions of GH/528, among which the surface and the outsole can be tested using 60T. When the test thickness does not reach the test standard, the test shall be carried out according to the actual standard thickness of the specimen. 6.4 Determination of the wear resistance of calcined rubber
The wear resistance of calcined rubber shall be determined according to the provisions of H/T189. When the test piece is not long enough, it can be slowed down in the direction of the outer sole. When the original thickness of the sample does not reach the test force method standard, the sample thickness test shall be carried out. 6.5 Rubber expansion test
Rubber hardness test shall be carried out according to the provisions of H/T531. If the test thickness does not meet the requirements, multiple layers can be added until the test requirements are met. ||t t||6.6 Adhesion strength test
Adhesion resistance strength test According to the environment of T532, take the test rod and take the film: take two waists, about longitudinal on both sides of the makeup, take a test rod, effective width is 1C, length 100--150mm, use a small sample to increase the effective width of the cloth and the opening, from the grid test support system vertically 40--50 length (that is, the effective length of the sample), 6.7 Continuous film elongation test
6.7. 1 Test piece
Cut a piece with a length of 120~125mm, a width of (10±0.2)mm, and the thickness of the original finished product, and mark the test piece with two marks with a spacing of (100-0.5)um.
6.7.2 Test step
After the test piece is fully stretched, place the test piece under the test piece at a speed of (100±i)mm/ia. When the test piece is stretched to the point where the paint film appears and the first bag appears, the test piece is stretched to the point where the paint film appears. 6.7.3 The result indicates that the film length is the length of the sieve according to the sieve.
In the formula, the distance from the original mark of the test piece to the original mark is about 1/2 of the distance from the original mark of the test piece to the original mark. HG/T 2019 2001
I. When a crack appears on the film, the distance between the test piece cup lines is m: Two test pieces are made for each pair of shoes, and the average value is taken. 6.8 The overall chemical test is carried out according to the provisions of B512. The aging test conditions are 70°C × 72°C. After aging, the sample is placed for 424 hours and then the tensile strength is measured. It is compared with the unaged test piece to calculate the tensile strength retention rate (%) of the tensile aging performance. The tensile strength retention rate (%) of the tensile aging performance is calculated according to (2): p
Where: A
Aging time of the sample, MPa; C Tensile amplitude of the sample before aging, MPa.
The value of aging energy retention rate (Xing) shall be accurate to 6.9 Determination of thickness
6.9.1 Determination of outer sole thickness
Retract the outer sole at the test point, cut off the outer sole edge, and leave the midsole and center core to obtain the boot sole. Determine along the center axis of the rubber sheet of the sole, use a vernier caliper to measure the thickness of the front palm force point, the back palm force point and the thickness of the bottom plate respectively, and take the maximum value of the obtained data, retaining one decimal place. 6.9.2 Determination of thickness
Cut the surface with the test piece, and separate it. When the film is obtained, use a rubber measuring device to measure the surface thickness, and take the minimum value, and retain one decimal place.
6.10 Test
The water resistance test shall be carried out in accordance with the provisions of HG/T3E64. 7 Inspection rules, marking, packaging, transportation and storage. Marking, packaging, transportation and storage shall be in accordance with the relevant provisions of HG/T2403 for shoes. The inspection of the outer thickness shall be in accordance with 3.2.1.2 of HG/T2403-7992. The aging test and micro-bearing test shall be in accordance with 3.3 of HG/T2403-1992. At the same time, the standard number 16 shall be marked on the packaging of each pair of shoes.6 Adhesion strength test
Adhesion resistance strength test According to the environment of T532, take the test piece from the test rod: take two waists, about the longitudinal direction of the two sides, take a test rod, effective width is 1C, length 100--150mm, use a small sample to increase the effective width of the cloth and the opening, from the grid test support system vertically cut 40--50 length (that is, the effective length of the sample), 6.7 Continuous film elongation test
6.7. 1 Test piece
Cut a piece with a length of 120~125mm, a width of (10±0.2)mm, and the original thickness of the finished product, and mark the test piece with two marks with a spacing of (100-0.5)um.
6.7.2 Test step
After the whole test piece is stretched to the bottom of the holder, the speed of the holder is (100±i)mm/ia. When the test piece is stretched to the point where the paint film appears and the first bag appears, the test drill ends. 6.7.3 The result indicates that
the film length is calculated according to the sieve.
In the formula, the test piece is about the distance from the original mark line to the test piece. HG/T 2019 2001
I. When a crack appears on the film, the distance between the test piece cup lines is m: Two test pieces are made for each pair of shoes, and the average value is taken. 6.8 The overall chemical test is carried out according to the provisions of B512. The aging test conditions are 70°C × 72°C. After aging, the sample is placed for 424 hours and then the tensile strength is measured. It is compared with the unaged test piece to calculate the tensile strength retention rate (%) of the tensile aging performance. The tensile strength retention rate (%) of the tensile aging performance is calculated according to (2): p
Where: A
Aging time of the sample, MPa; C Tensile amplitude of the sample before aging, MPa.
The value of aging energy retention rate (Xing) shall be accurate to 6.9 Determination of thickness
6.9.1 Determination of outer sole thickness
Retract the outer sole at the test point, cut off the outer sole edge, and leave the midsole and center core to obtain the boot sole. Determine along the center axis of the rubber sheet of the sole, use a vernier caliper to measure the thickness of the front palm force point, the back palm force point and the thickness of the bottom plate respectively, and take the maximum value of the obtained data, retaining one decimal place. 6.9.2 Determination of thickness
Cut the surface with the test piece, and separate it. When the film is obtained, use a rubber measuring device to measure the surface thickness, and take the minimum value, and retain one decimal place.
6.10 Test
The water resistance test shall be carried out in accordance with the provisions of HG/T3E64. 7 Inspection rules, marking, packaging, transportation and storage. Marking, packaging, transportation and storage shall be in accordance with the relevant provisions of HG/T2403 for the batch (shoes). The inspection of the outer thickness shall be in accordance with 3.2.1.2 of HG/T2403-7992. The aging test and micro-bearing test shall be in accordance with 3.3 of HG/T2403-1992. At the same time, the standard number 16 shall be marked on the packaging of each pair of (shoes).6 Adhesion strength test
Adhesion resistance strength test According to the environment of T532, take the test piece from the test rod: take two waists, about the longitudinal direction of the two sides, take a test rod, effective width is 1C, length 100--150mm, use a small sample to increase the effective width of the cloth and the opening, from the grid test support system vertically cut 40--50 length (that is, the effective length of the sample), 6.7 Continuous film elongation test
6.7. 1 Test piece
Cut a piece with a length of 120~125mm, a width of (10±0.2)mm, and the original thickness of the finished product, and mark the test piece with two marks with a spacing of (100-0.5)um.
6.7.2 Test step
After the whole test piece is stretched to the bottom of the holder, the test piece is accurately loaded under the holder at a speed of (100±i)mm/ia. When the test piece is stretched to the point where the paint film appears and the first bag appears, the test drill ends. 6.7.3 The result indicates that
the film length is calculated according to the sieve.
In the formula, the test piece is about the distance from the original mark line to the test piece. HG/T 2019 2001
I. When a crack appears on the film, the distance between the test piece cup lines is m: Two test pieces are made for each pair of shoes, and the average value is taken. 6.8 The overall chemical test is carried out according to B512. The aging test conditions are 70°C × 72°C. After aging, the sample is placed for 424 hours and then the tensile strength is measured. It is compared with the unaged test piece to calculate the tensile strength retention rate (%) of the tensile aging performance. The tensile strength retention rate (%) of the tensile aging performance is calculated according to (2): p
Where: A
Aging time of the sample, MPa; C Tensile amplitude of the sample before aging, MPa.
The value of aging energy retention rate (Xing) shall be accurate to 6.9 Determination of thickness
6.9.1 Determination of outer sole thickness
Retract the outer sole at the test point, cut off the outer sole edge, and leave the midsole and center core to obtain the boot sole. Determine along the center axis of the rubber sheet of the sole, use a vernier caliper to measure the thickness of the front palm force point, the back palm force point and the thickness of the bottom plate respectively, and take the maximum value of the obtained data, retaining one decimal place. 6.9.2 Determination of thickness
Cut the surface with the test piece, and separate it. When the film is obtained, use a rubber measuring device to measure the surface thickness, and take the minimum value, and retain one decimal place.
6.10 Test
The water resistance test shall be carried out in accordance with the provisions of HG/T3E64. 7 Inspection rules, marking, packaging, transportation and storage. Marking, packaging, transportation and storage shall be in accordance with the relevant provisions of HG/T2403 for the batch (shoes). The inspection of the outer thickness shall be in accordance with 3.2.1.2 of HG/T2403-7992. The aging test and micro-bearing test shall be in accordance with 3.3 of HG/T2403-1992. At the same time, the standard number 16 shall be marked on the packaging of each pair of (Gui)
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.