JJF 1016-2002 Guidelines for Writing Type Evaluation Outlines for Measuring Instruments JJF1016-2002 Standard download decompression password: www.bzxz.net
This guideline is applicable to writing type evaluation outlines for measuring instruments. It is used as a reference when writing prototype test outlines for measuring instruments.

National Metrology Technical Specification of the People's Republic of China J.TF1016—2002bzxz.net
The Rules for Drafting Program of Pattern Evahuation of Measuring Instruments2002-05-16 Issued
Implementation on 2002-08-01
The General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China issued JJF1016-20-02
The Rules for Irafting Program of Pattern Evaluutiun of Measuring InstrumentsJJF 1016—20H2
Replaces JJF1016—1990
This specification was approved by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China on May 16, 2002, and came into effect on August 1, 2002.
Responsible unit: National Legal System Quality Management Quality Technical Committee Drafting unit: Measurement Department of General Administration of Quality Supervision, Inspection and Quarantine Liaoning Provincial Quality and Technical Bureau
This specification is issued by the Metrology Department of General Administration of Quality Supervision, Inspection and Quarantine and is responsible for interpreting this specification. Main drafters:
Zhang Juyun
Huan Lihua
Tang Leqiu
Participants in the drafting of the chapter:
Zhang Wenmei
Zhang Yujian
J3F10162002
(Metrology Department of General Administration of Quality Supervision, Inspection and Quarantine) (Liaoning Provincial Quality and Technical Supervision Bureau)
(Jiangning Provincial Measurement Science Research Institute)
【Liaoning Institute of Metrology
(Liaoning Provincial Measurement Science Research Institute)
(Liaoning Provincial Measurement Science Research Institute) Institute of Technology)
Citations
Type evaluation personnel's version
Contents of each part of the type evaluation personnel's shoes 5.1
Citations
Technology, symbols, practices
JJF10J6—2002
Technical documents and test methods for review Management requirements
Design requirements
Technical requirements
Type evaluation body
Type evaluation working methods
Necessary methods of type evaluation
Type evaluation results planning
Editing details
1 Scope
JJF1016—20U2
Guidelines for writing the outline of type evaluation of measuring instruments This guideline is applicable to the writing of the outline of type evaluation of measuring instruments. When compiling the prototype test of the measuring instrument, it shall be used as a reference.
2 References
11JF1002—1998 Rules for compiling national metrological verification procedures21JJF1001—1998 General terms and definitions of quantities31JJF1015—2002 Specification for type evaluation and type approval of measuring instruments24Pritur:iplaa of μ:lantin of haractcriatics for the verification of measuring instruments.OIMLD15,198G(E)
O1ML International Document No.15 "Principles of selection of special notes for the inspection of measuring instruments"3 When using this guide, the currently valid versions of the above references shall be used. 3 General Principles The purpose of type evaluation is to provide a basis for type approval or screening approval. The outline should be: in accordance with the provisions of relevant laws and regulations; scientific and reasonable, and operational; the text should be well structured, clear in level and accurate in use; the technical specifications, symbols, codes, etc. used should be unified; the formulas, tables, drawings and data should be accurate and in accordance with the requirements; the international standards, international documents and international standards should be adopted. 4 Composition of type evaluation outline The general composition and arrangement order of type evaluation outline are as follows: - List: - References; - Scope; - Citations; - Technical specifications, symbols, codes; - Description: - Technical documents for review and test prototypes ：1. Legal requirements:
Summer requirements;
According to technical requirements;
Type evaluation method:
Open evaluation items and methods:
And type evaluation results processing:
Appendix.
According to the city: sound and at the top
5 Contents of each component of the type evaluation outline 5.: Village surface
JJF1016—·20 02
The name and box number of the blood type evaluation format on the cover: the symptoms and the period of the love cloth (twisted tape). The evaluation of the period should be simple and clear, and the use of the certificate should be compared with the use of the certificate: 5.2 page
Non-quality general package, drafting list, person who draws up dishes, and approver information 5.3 record
Safety according to 10021598 image card inspection regulations, etc. 5 chapters 13 provisions: 5.4
Continue 1m219 for the current national standards and regulations for the current national standards and regulations, delete the 5th chapter 5.1: 5.5 Specifications
Specifications should be generally clear and suitable for the design and use of equipment. If necessary, it should also be clearly stated! Inapplicable specifications should be used in the following typical products:
"This evaluation outline applies to..." 5.6 References
For references to documents that are missing: national standards, national standards, international standards, national standards, industry standards, enterprise standards, departments or planning regulations. The referenced documents should state the key points, such as; use, equivalent use..., equivalent use..., and indicate the number and name of the referenced document. Add "When using, please note that the current valid version of the above referenced document is not used" after the quantity. 5.? The six terms, symbols, and codes in the type evaluation outline are not yet specified in the current national technical regulations, and they must be defined or mentioned in the outline. 5.8 Description
The general part briefly describes the purpose, principle, and structure of the design equipment: 5.9 Technical documents for inspection
According to the 101203 type evaluation equipment type evaluation standard, the technical requirements of the design equipment should be provided, and the sample room requirements and the number of samples should be provided: 5.0 legal creation official ticket requirements
JJI10162002
According to JF1015-205 general specifications for type evaluation and approval, the legal management requirements are proposed. The three units of the package are the version level and the requirements of the design right legal training and compliance.
s. Hope to require
According to JJ1-2U2 metering equipment type certification price in the type approval of the "specification", and refer to the metering equipment inspection characteristics of the selection principle) (inter-provincial document Nn.15: etc.) to put forward the metering quantity that should be measured.
5.12 Technical requirements
Collect a metering three-point type price type approval speed use standard to propose appropriate production technology. The technical requirements are proposed: it cannot limit the development of the metering technology, this The three performances must be maintained during use; the measurement results must be reliable and simple; the following should be clearly stated:
Eliminate possible behaviors as much as possible;
Ensure the safety of the design.
Technical requirements and structure of the design are in order to ensure that the design can be used normally, and can give more orthodox measurement results. S.13 Type evaluation items H
Type evaluation items should be clearly stated. Type evaluation is mainly to meet the requirements of 5.11, 5.1, 5.12 through selected tests. Generally, it is not directly for the structure of the product, but for the test of the structure and performance of the whole material. It can put forward the test objectives of the design and material flow. 5. Type evaluation conditions and methods t||The conditions and methods of type evaluation should be based on the items of the certification. Generally include: the name of the test equipment, the accuracy and measurement range of the test; the test conditions, test conditions, preparations before the test: calculation formula, record format and data processing variance. The terms and methods of type evaluation should be as consistent as possible with the actual application conditions and descriptions, so that each type evaluation personnel can draw a valid test conclusion based on the test conditions and methods that meet the requirements: 5.The evaluation system adopts the processing of type evaluation results, including: the judgment principle of type evaluation results; the most necessary type evaluation documents; (00 only type evaluation and type approval specification): the price model of the parts includes 5.16 appendix; appendix: the type test method of the parts, the three-tenths test method, the calculation table, the technical specifications of the improvement; the division of the level of type evaluation outline; JJF 1016 20N12; follow the provisions of Chapter 6 of JJF1002-1998 National Registration Verification Regulations Compilation Rules! Compiled in accordance with the provisions of JF1002-1998 "National Verification Regulations" Chapter 7.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.