Some standard content:
ICS 47.020. 10
National Standard of the People's Republic of China
GB/T5746—2001
neq ISO 3903:1993
Ships' ordinary rectangular window2001-12~13 Issued
People's Republic of China
General Administration of Quality Supervision, Inspection and Quarantine
2002-08-01Implementation
GB/T5746—2001
This standard adopts the international standard ISO3903:1993 & Shipbuilding and marine structures Ordinary rectangular windows for ships, and implements the 199G amendments to the International Convention for the Safety of Life at Sea (SALE 1974) and the 1966 amendments GB/T 57461996 Ordinary Rectangular Windows for Ships was revised based on the experience of the International Convention on Loading and Carrying Capacity in 1996. The general rules in the technical requirements were supplemented with specific detailed requirements and indicators, and the material code 222 for bolted windows was added. 202; For the manufacturing materials of the main parts, the specific material grades of my country are supplemented, and the provisions of the standardization work guidelines of my country are adopted. The inspection rules are supplemented. According to the requirements of GB/T17434-1998 Technical Conditions for Marine Fire Reduction Windows 3, the rectangular windows that can be installed in the "A" grade fire-resistant partition area are supplemented, and the fire resistance level is revised to: A-60, A30, A15, A0, B15 and B-0. The general rules, test methods, inspection rules and other contents in the requirements are revised and revised. In order to clarify the definition of the window opening direction, in Appendix C:, the window opening direction is explained with cloud intention. Its content is consistent with the provisions of IS0/R1226-1:1970 "Method for the symbolic representation of the fan and closing direction of doors and windows Part 1", and is also consistent with the definition of the door and window opening direction in my country's national standard GB/T 8242.3. From the date of implementation of this standard, it replaces the appendix A, appendix B and appendix C of G35746-1996. This standard is proposed by China Shipbuilding Industry Corporation II and approved by Jiangnan Shipyard (Group) Co., Ltd. of China Shipbuilding Industry Corporation I. The drafting units of this standard are Hudong Shipyard and Huangshan Ship Parts Factory. The main drafters of this standard are Wen Xing, Shao Jinhua, Chen Yindi and Yao Meiqin. GB/T5746-2001
ISO Foreword
ISO (International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The formulation of international standards is usually carried out by ISO technical committees. Each member body has the right to participate in the subject of a technical committee. International organizations, both governmental and non-governmental, in contact with ISO may also participate in this work. ISO) works closely with the International Electrotechnical Commission (IEC) in the standardization of electrotechnical technology. The draft international standards approved by the technical committees are first circulated to the member groups for voting. The publication of international standards shall be approved by at least 75% of the member groups voting.
International Standard ISO3903 was prepared by ISO/TC8 "Architecture and Offshore Structures" Technical Committee SC8 "Windows and Windows". The second edition is a technical revision of the first edition and replaces the first edition (IS03903:1977). Annexes A and B are integral parts of this standard. 1 Scope
National Standard of the People's Republic of China
Ships' orlinary reclangular windows
Ships' orlinary reclangular windows GB/E5746-2001
neq ISO. 3903: 1993
Agency GB/T 57461996
This standard specifies the classification, requirements, test methods, inspection rules, marking, packaging, transportation and treatment of ordinary rectangular windows for ships (hereinafter referred to as rectangular windows).
This standard is applicable to rectangular windows installed in deckhouses and superstructures of ocean-going ships and related cabins of offshore structures above the sea level. The positioning is in accordance with GB/T14357. Rectangular windows installed on inland vessels can also be used as a reference. 2 Reference standards
The following The texts contained in the standard shall become the provisions of this standard by citing it in this standard. When this standard is published, the versions shown are valid. All standards will be subject to the use of this standard. The service provider should explore the possibility of using the latest version of the following standards. GB101: 200C Packaging, storage and transportation pictorial marking
GBT3385-1982 Marine windows and short-shaped tempered glass non-destructive ring strength test punching method (eqVISO61419761
GB/T 6388-1986 Shipping packaging delivery and receipt mark GB/T8242.3-1987 Hull equipment technical specifications for deck accessories (neqISO/DP6345) (B1146-1989 Marine toughened safety glass (ncq1SO)1095:1976) GB14357-1993 Positioning of ordinary shaped windows on the yin of ships (c9ISO8279:1987) GB/T17434-1998 Technical conditions for fire windows on ships (nc4ISO59 7-1:1989) CB/3873-1999 Rectangular window sealing material CB*/292-1981 Aluminum alloy anodizing treatment CB*/343-1984 Hot dip galvanizing general process
1SO3434:1992 Rectangular window for use in ships and offshore structures
This standard adopts the following definitions.
3.1 Ordinary rectangular window for ships
A short rectangular window that can be opened and closed by hinges composed of vertical and horizontal angles and cannot be opened. 3.2 Main frame
The main frame connecting the window to the installation part.
3.3 Glaalolder
A frame that can be opened and closed and equipped with glass.
3.4 Fasteners
A general term for the living bolts in round hole hinges and locking devices that ensure the tightness and weathertightness of rectangular windows. Long round or long hole hinges shall not be counted as fasteners.
Approved by the General Administration of Quality Supervision, Inspection and Quarantine of the People's Republic of China in 2001-1213 and implemented on August 1, 2002
4 Classification
GB/T 5746-2001
The series, type, style, nominal size code, comprehensive characteristics and main dimensions are specified in 4.1 to 4.5 respectively. 4.1 Series
4.1.1 General series (N)
General series rectangular windows are rectangular windows equipped with tempered glass and are commonly used in ships. 4.1.2 Fire-resistant series (F)
Fire-resistant series rectangular windows are rectangular windows installed in Class A or Class B fire-resistant partitions and meet the requirements of GB/T 17434. 4.1.3 Heating series (H)
Heating series rectangular windows are rectangular windows equipped with heated glass that meets the requirements of GB/T 17434. 4.2 Type
Heavy duty rectangular windows:
Light duty short-duty windows.
4.3 Type
The types of rectangular windows are specified in Table 1 according to the main characteristics such as opening (or closing) type, opening direction and installation method. Table 1 Rectangular fungus unique features
Opening piano
Opening large space
Side chain
Upper general chain
Upper hinge
Short window bottom opening direction according to Appendix C standard) provisions: 4.4 Nominal size code
Screw light type
Installation method
Forced replacement
Type code
Nominal size is the light transmission size of the rectangular model, width te: and height - in meters The unit is identified by a code. The regulations are shown in Table 2. 4.5 Comprehensive characteristics and main dimensions Nominal dimensions 300X425 355X50C 400x56c 450x630 500X710 56EX800 9G0X630 1100X710 GB/T 5746-200T Table Nominal dimensions 4.5.1 Comprehensive characteristics of the shape are shown in Table 3.Applicable to N (General) series, P (Fermentation) series and (Heating) series. The diagram in the table does not limit its structure.
Table 3 Comprehensive characteristics of rectangular separation
Installation type
Butterfly bolt type
Braid type
Nominal size code
(Screw bolt type)
Installation type
Source type
Avoid type
GB/T 5745--2001
Pei 3 (continued)
Nominal size code
(Block type window]
Case installation type
GB/T 5746--2001
Table 3 (end)
Nominal size code
(See 4.#)
4. 5. 2 The main dimensions of the rectangular shade are as shown in Figure 1 and Table 4. The main dimensions and hardware quantities of Table 1 are shown in Table 1. Nominal dimensions: 330X425X300
3555000
100568x60
150X630X100
50)770×100
561X800X00
900X630X10m
1 000X710X100
11oX8x
11The function of fasteners includes fastening devices and national chain, 5.1f
(screw type tight)
fastening base
352X477XR76
417X652XR7S
1>2X62R73
502X682XR126
552X762XR126
612X852XR126
9:2X652XR126
1052X762XR120
1 132×8E2 R126
CB/T 5746-2001
Pet-shaped ringworm
One series
Fire Thai chicken
Heating series
GB/T5746--2001
Table 5 Glass thickness
Nominal foot No. 4
1) In special combination, for thicker medical sand, the distance from 5.3.1 and Table 14.4.5.3 Corner radius
RGB/F17434
See 1s03134
The reference half is the fillet radius of the fillet size (see table): the outer corner radius of the shoulder and the outer corner radius of the main tooth connection =: 24 num+flange vertical diameter, t, ±65 mm maximum), 4.5.4 Convex height
The convexity of the main frame. According to Table 6, the actual requirements can be confirmed when ordering windows. Table 6 Depth of projection (inch e) || tt || Spicy vegetarian chicken || tt || 4.5.5 Glass installation || tt || Glass installation groove (zl, h,, rl) dimensions are measured according to Figure 2 Table 7. Processing height
Actual height
The actual height can be determined when ordering
Nominal size
2, ×ht
300X125
355X:00
400X560
150X630
500X710
551X800
900X630
1100X800
4.5.6 Glass pressing plate
Type I glass
GB/T 5746 - 2001
Nominal size (wxh)
wxhixr
Figure 2 Glass installation summary
Table 7 Glass installation groove
Corrugated size
314X439XR58
369X514XR58
414XG74XR58
AG4XM4XR103
514XI24XRI08
574X14XR10
914X644XR 108
1014XT24XR108
1II+X81IXRI0R
This ruler is made by the factory
Nano glass screen thickness and cable determination
glass pressure can be selected arbitrarily, its minimum size is according to Figure 3, the maximum value of the pressure plate nail is according to Table 8, the burst nail should have the following characteristics, butterfly pattern: M6:
Screw length: 16mmt
Material: Seawater corrosion-resistant steel alloy (for copper alloy seals) or stainless steel (for aluminum alloy or pot windows). 90*
Metric metric "WXm)
a) For cylindrical head nails
4.6 Product marking
Figure 3 Glass pressure plate
Table 8 Pressure plate burst nail spacing
b) For head screws
End nail spacing (max)
The product marking is composed of a rectangular name, feature code and standard number arranged in the following order. 4.7 Example of He Fan
4.7.1 General series rectangular window (N)
GB/T 5746-2001
Standard
General series see 5.3.1
Glass code (or fire grade film fire resistance series see 5.3.2 Heating series see 5, 33 and Table 14
Material combination code (see Table 11)
Type code (see Table 1)
Shoulder height (see 4.5.4)
Nominal size guide (see Table 2)
Type (see 4.2)
Series code (see 4. 1)
-Name
-Number Series (N) Heavy duty, public size 455X63 code 4), shoulder height 16mm, side hinge inward left open bolt installation type [II.13), material combination 111, transparent boundary plate broken glass (Y1) rectangular window marked as follows: thin window N F4X16-ILB-111-Y1 GB/T 574R--29014.7.2 fire-resistant structure rectangular window (P)
Fire series (P) Hui type, public size 456×630 code 4) convex room height 16mm German chain inward left open explosion inspection installation type (II.), material combination 113, fire glass B-15 energy window marked as follows: short image P: FAX15-ILB-21I-BI5 GB/T 3746-20014.7.3 Heating bottle-shaped window (H)
Heating bottle-shaped window (H) is a rectangular window with a nominal dimension of 450×630 (code 4), a boss width of 16m, a left-opening welding installation between hinges (11.W), a material combination of 233, a group adjustment, an overheating protection device, a power load of 12W/dm2, an AC single-phase 22nV, and a 501z power supply. The rectangular size of the heating window (code 12G4) is as follows: Rectangular window H-E4X16-JI.W-233-12G14GB/T5746--20015 Specifications
5.1.1 The main dimensions of the rectangular window shall comply with the provisions of Table 4: all common parts can be interchangeable. For rectangular windows of similar size, all its parts should be interchangeable. The difference in length between the two diagonals of the main window cabinet and the fan handle should be less than 2Tan. 5.1.2 The surface of the super-shaped window parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have cracks, delamination, burns and other forging defects. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the galvanized layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. After the flushing test in 6.1, there shall be no water leakage or water marks in the inspection parts. 5.1.7 The short window shall have a certain water tightness. After the water pressure test in 6.5, there shall be no leakage in all parts. 5.1.8 The short-circuit should have sufficient strength (see Appendix A (Standard Appendix) and Appendix B (Standard Appendix) for the maximum allowable filling pressure) 1. According to 6.S mechanical strength test. After unloading, the light should be permanently deteriorated.After uninstallation, the light will become permanently bad.After uninstallation, the image will become permanently bad.1f
(screw-type seal)
tightly trapped number base
352X477XR76
417X652XR7S
1>2X62R73
502X682XR126
552X762XR126
612X852XR126
9:2X652XR126
1052X762XR120
1 132×8E2 R126
CB/T 5746-2001
Pet-shaped ringworm
One series
Fire Thai chicken
Heating series
GB/T5746--2001
Table 5 Glass thickness
Nominal foot No. 4
1) In special combination, for thicker medical sand, the distance from 5.3.1 and Table 14.4.5.3 Corner radius
RGB/F17434
See 1s03134
The reference half is the fillet radius of the fillet size (see table): the outer corner radius of the shoulder and the outer corner radius of the main tooth connection =: 24 num+flange vertical diameter, t, ±65 mm maximum), 4.5.4 Convex height
The convexity of the main frame. According to Table 6, the actual requirements can be confirmed when ordering windows. Table 6 Depth of projection (inch e) || tt || Spicy vegetarian chicken || tt || 4.5.5 Glass installation || tt || Glass installation groove (zl, h,, rl) dimensions are measured according to Figure 2 Table 7. Processing height
Actual height
The actual height can be determined when ordering
Nominal size
2, ×ht
300X125
355X:00
400X560
150X630
500X710
551X800
900X630
1100X800
4.5.6 Glass pressing plate
Type I glass
GB/T 5746 - 2001
Nominal size (wxh)
wxhixr
Figure 2 Glass installation summary
Table 7 Glass installation groove
Corrugated size
314X439XR58
369X514XR58
414XG74XR58
AG4XM4XR103
514XI24XRI08
574X14XR10
914X644XR 108
1014XT24XR108
1II+X81IXRI0R
This ruler is made by the factory
Nano glass screen thickness and cable determination
glass pressure can be selected arbitrarily, its minimum size is according to Figure 3, the maximum value of the pressure plate nail is according to Table 8, the burst nail should have the following characteristics, butterfly pattern: M6:
Screw length: 16mmt
Material: Seawater corrosion-resistant steel alloy (for copper alloy seals) or stainless steel (for aluminum alloy or pot windows). 90*
Metric metric "WXm)
a) For cylindrical head nails
4.6 Product marking
Figure 3 Glass pressure plate
Table 8 Pressure plate burst nail spacing
b) For head screws
End nail spacing (max)
The product marking is composed of a rectangular name, feature code and standard number arranged in the following order. 4.7 Example of He Fan
4.7.1 General series rectangular window (N)
GB/T 5746-2001
Standard
General series see 5.3.1
Glass code (or fire grade film fire resistance series see 5.3.2 Heating series see 5, 33 and Table 14
Material combination code (see Table 11)
Type code (see Table 1)
Shoulder height (see 4.5.4)
Nominal size guide (see Table 2)
Type (see 4.2)
Series code (see 4. 1)
-Name
-Number Series (N) Heavy duty, public size 455X63 code 4), shoulder height 16mm, side hinge inward left open bolt installation type [II.13), material combination 111, transparent boundary plate broken glass (Y1) rectangular window marked as follows: thin window N F4X16-ILB-111-Y1 GB/T 574R--29014.7.2 fire-resistant structure rectangular window (P)
Fire series (P) Hui type, public size 456×630 code 4) convex room height 16mm German chain inward left open explosion inspection installation type (II.), material combination 113, fire glass B-15 energy window marked as follows: short image P: FAX15-ILB-21I-BI5 GB/T 3746-20014.7.3 Heating bottle-shaped window (H)
Heating bottle-shaped window (H) is a rectangular window with a nominal dimension of 450×630 (code 4), a boss width of 16m, a left-opening welding installation between hinges (11.W), a material combination of 233, a group adjustment, an overheating protection device, a power load of 12W/dm2, an AC single-phase 22nV, and a 501z power supply. The rectangular size of the heating window (code 12G4) is as follows: Rectangular window H-E4X16-JI.W-233-12G14GB/T5746--20015 Specifications
5.1.1 The main dimensions of the rectangular window shall comply with the provisions of Table 4: all common parts can be interchangeable. For rectangular windows of similar size, all its parts should be interchangeable. The difference in length between the two diagonals of the main window cabinet and the fan handle should be less than 2Tan. 5.1.2 The surface of the super-shaped window parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have cracks, delamination, burns and other forging defects. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the galvanized layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. After the flushing test in 6.1, there shall be no water leakage or water marks in the inspection parts. 5.1.7 The short window shall have a certain water tightness. After the water pressure test in 6.5, there shall be no leakage in all parts. 5.1.8 The short-circuit should have sufficient strength (see Appendix A (Standard Appendix) and Appendix B (Standard Appendix) for the maximum allowable filling pressure) 1. According to 6.S mechanical strength test. After unloading, the light should be permanently deteriorated.1f
(screw-type seal)
tightly trapped number base
352X477XR76
417X652XR7S
1>2X62R73
502X682XR126
552X762XR126
612X852XR126
9:2X652XR126
1052X762XR120
1 132×8E2 R126
CB/T 5746-2001
Pet-shaped ringworm
One series
Fire Thai chicken
Heating series
GB/T5746--2001
Table 5 Glass thickness
Nominal foot No. 4
1) In special combination, for thicker medical sand, the distance from 5.3.1 and Table 14.4.5.3 Corner radius
RGB/F17434
See 1s03134
The reference half is the fillet radius of the fillet size (see table): the outer corner radius of the shoulder and the outer corner radius of the main tooth connection =: 24 num+flange vertical diameter, t, ±65 mm maximum), 4.5.4 Convex height
The convexity of the main frame. According to Table 6, the actual requirements can be confirmed when ordering windows. Table 6 Depth of projection (inch e) || tt || Spicy vegetarian chicken || tt || 4.5.5 Glass installation || tt || Glass installation groove (zl, h,, rl) dimensions are measured according to Figure 2 Table 7. Processing height
Actual height
The actual height can be determined when ordering
Nominal size
2, ×ht
300X125
355X:00
400X560Www.bzxZ.net
150X630
500X710
551X800
900X630
1100X800
4.5.6 Glass pressing plate
Type I glass
GB/T 5746 - 2001
Nominal size (wxh)
wxhixr
Figure 2 Glass installation summary
Table 7 Glass installation groove
Corrugated size
314X439XR58
369X514XR58
414XG74XR58
AG4XM4XR103
514XI24XRI08
574X14XR10
914X644XR 108
1014XT24XR108
1II+X81IXRI0R
This ruler is made by the factory
Nano glass screen thickness and cable determination
glass pressure can be selected arbitrarily, its minimum size is according to Figure 3, the maximum value of the pressure plate nail is according to Table 8, the burst nail should have the following characteristics, butterfly pattern: M6:
Screw length: 16mmt
Material: Seawater corrosion-resistant steel alloy (for copper alloy seals) or stainless steel (for aluminum alloy or pot windows). 90*
Metric metric "WXm)
a) For cylindrical head nails
4.6 Product marking
Figure 3 Glass pressure plate
Table 8 Pressure plate burst nail spacing
b) For head screws
End nail spacing (max)
The product marking is composed of a rectangular name, feature code and standard number arranged in the following order. 4.7 Example of He Fan
4.7.1 General series rectangular window (N)
GB/T 5746-2001
Standard
General series see 5.3.1
Glass code (or fire grade film fire resistance series see 5.3.2 Heating series see 5, 33 and Table 14
Material combination code (see Table 11)
Type code (see Table 1)
Shoulder height (see 4.5.4)
Nominal size guide (see Table 2)
Type (see 4.2)
Series code (see 4. 1)
-Name
-Number Series (N) Heavy duty, public size 455X63 code 4), shoulder height 16mm, side hinge inward left open bolt installation type [II.13), material combination 111, transparent boundary plate broken glass (Y1) rectangular window marked as follows: thin window N F4X16-ILB-111-Y1 GB/T 574R--29014.7.2 fire-resistant structure rectangular window (P)
Fire series (P) Hui type, public size 456×630 code 4) convex room height 16mm German chain inward left open explosion inspection installation type (II.), material combination 113, fire glass B-15 energy window marked as follows: short image P: FAX15-ILB-21I-BI5 GB/T 3746-20014.7.3 Heating bottle-shaped window (H)
Heating bottle-shaped window (H) is a rectangular window with a nominal dimension of 450×630 (code 4), a boss width of 16m, a left-opening welding installation between hinges (11.W), a material combination of 233, a group adjustment, an overheating protection device, a power load of 12W/dm2, an AC single-phase 22nV, and a 501z power supply. The rectangular size of the heating window (code 12G4) is as follows: Rectangular window H-E4X16-JI.W-233-12G14GB/T5746--20015 Specifications
5.1.1 The main dimensions of the rectangular window shall comply with the provisions of Table 4: all common parts can be interchangeable. For rectangular windows of similar size, all its parts should be interchangeable. The difference in length between the two diagonals of the main window cabinet and the fan handle should be less than 2Tan. 5.1.2 The surface of the super-shaped window parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have cracks, delamination, burns and other forging defects. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the galvanized layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. After the flushing test in 6.1, there shall be no water leakage or water marks in the inspection parts. 5.1.7 The short window shall have a certain water tightness. After the water pressure test in 6.5, there shall be no leakage in all parts. 5.1.8 The short-circuit should have sufficient strength (see Appendix A (Standard Appendix) and Appendix B (Standard Appendix) for the maximum allowable filling pressure) 1. According to 6.S mechanical strength test. After unloading, the light should be permanently deteriorated.00
400X560
150X630
500X710
551X800
900X630
1100X800
4.5.6 Glass platen
Type 1 glass
GB/T 5746 - 2001
Nominal size (wxh)
wxhixr
Figure 2 Glass installation summary
Table 7 Glass installation groove
Corrugated size
314X439XR58
369X514XR58
414XG74XR58
AG4XM4XR103
514XI24XRI08
574X14XR10
914X644XR 108
1014XT24XR108
1II+X81IXRI0R
This ruler is made by the factory
Nano glass screen thickness and cable determination
glass pressure can be selected arbitrarily, its minimum size is according to Figure 3, the maximum value of the pressure plate nail is according to Table 8, the burst nail should have the following characteristics, butterfly pattern: M6:
Screw length: 16mmt
Material: Seawater corrosion-resistant steel alloy (for copper alloy seals) or stainless steel (for aluminum alloy or pot windows). 90*
Metric metric "WXm)
a) For cylindrical head nails
4.6 Product marking
Figure 3 Glass pressure plate
Table 8 Pressure plate burst nail spacing
b) For head screws
End nail spacing (max)
The product marking is composed of a rectangular name, feature code and standard number arranged in the following order. 4.7 Example of He Fan
4.7.1 General series rectangular window (N)
GB/T 5746-2001
Standard
General series see 5.3.1
Glass code (or fire grade film fire resistance series see 5.3.2 Heating series see 5, 33 and Table 14
Material combination code (see Table 11)
Type code (see Table 1)
Shoulder height (see 4.5.4)
Nominal size guide (see Table 2)
Type (see 4.2)
Series code (see 4. 1)
-Name
-Number Series (N) Heavy duty, public size 455X63 code 4), shoulder height 16mm, side hinge inward left open bolt installation type [II.13), material combination 111, transparent boundary plate broken glass (Y1) rectangular window marked as follows: thin window N F4X16-ILB-111-Y1 GB/T 574R--29014.7.2 fire-resistant structure rectangular window (P)
Fire series (P) Hui type, public size 456×630 code 4) convex room height 16mm German chain inward left open explosion inspection installation type (II.), material combination 113, fire glass B-15 energy window marked as follows: short image P: FAX15-ILB-21I-BI5 GB/T 3746-20014.7.3 Heating bottle-shaped window (H)
Heating bottle-shaped window (H) is a rectangular window with a nominal dimension of 450×630 (code 4), a boss width of 16m, a left-opening welding installation between hinges (11.W), a material combination of 233, a group adjustment, an overheating protection device, a power load of 12W/dm2, an AC single-phase 22nV, and a 501z power supply. The rectangular size of the heating window (code 12G4) is as follows: Rectangular window H-E4X16-JI.W-233-12G14GB/T5746--20015 Specifications
5.1.1 The main dimensions of the rectangular window shall comply with the provisions of Table 4: all common parts can be interchangeable. For rectangular windows of similar size, all its parts should be interchangeable. The difference in length between the two diagonals of the main window cabinet and the fan handle should be less than 2Tan. 5.1.2 The surface of the super-shaped window parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have cracks, delamination, burns and other forging defects. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the galvanized layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. After the flushing test in 6.1, there shall be no water leakage or water marks in the inspection parts. 5.1.7 The short window shall have a certain water tightness. After the water pressure test in 6.5, there shall be no leakage in all parts. 5.1.8 The short-circuit should have sufficient strength (see Appendix A (Standard Appendix) and Appendix B (Standard Appendix) for the maximum allowable filling pressure) 1. According to 6.S mechanical strength test. After unloading, the light should be permanently deteriorated.00
400X560
150X630
500X710
551X800
900X630
1100X800
4.5.6 Glass platen
Type 1 glass
GB/T 5746 - 2001
Nominal size (wxh)
wxhixr
Figure 2 Glass installation summary
Table 7 Glass installation groove
Corrugated size
314X439XR58
369X514XR58
414XG74XR58
AG4XM4XR103
514XI24XRI08
574X14XR10
914X644XR 108
1014XT24XR108
1II+X81IXRI0R
This ruler is made by the factory
Nano glass screen thickness and cable determination
glass pressure can be selected arbitrarily, its minimum size is according to Figure 3, the maximum value of the pressure plate nail is according to Table 8, the burst nail should have the following characteristics, butterfly pattern: M6:
Screw length: 16mmt
Material: Seawater corrosion-resistant steel alloy (for copper alloy seals) or stainless steel (for aluminum alloy or pot windows). 90*
Metric metric "WXm)
a) For cylindrical head nails
4.6 Product marking
Figure 3 Glass pressure plate
Table 8 Pressure plate burst nail spacing
b) For head screws
End nail spacing (max)
The product marking is composed of a rectangular name, feature code and standard number arranged in the following order. 4.7 Example of He Fan
4.7.1 General series rectangular window (N)
GB/T 5746-2001
Standard
General series see 5.3.1
Glass code (or fire grade film fire resistance series see 5.3.2 Heating series see 5, 33 and Table 14
Material combination code (see Table 11)
Type code (see Table 1)
Shoulder height (see 4.5.4)
Nominal size guide (see Table 2)
Type (see 4.2)
Series code (see 4. 1)
-Name
-Number Series (N) Heavy duty, public size 455X63 code 4), shoulder height 16mm, side hinge inward left open bolt installation type [II.13), material combination 111, transparent boundary plate broken glass (Y1) rectangular window marked as follows: thin window N F4X16-ILB-111-Y1 GB/T 574R--29014.7.2 fire-resistant structure rectangular window (P)
Fire series (P) Hui type, public size 456×630 code 4) convex room height 16mm German chain inward left open explosion inspection installation type (II.), material combination 113, fire glass B-15 energy window marked as follows: short image P: FAX15-ILB-21I-BI5 GB/T 3746-20014.7.3 Heating bottle-shaped window (H)
Heating bottle-shaped window (H) is a rectangular window with a nominal dimension of 450×630 (code 4), a boss width of 16m, a left-opening welding installation between hinges (11.W), a material combination of 233, a group adjustment, an overheating protection device, a power load of 12W/dm2, an AC single-phase 22nV, and a 501z power supply. The rectangular size of the heating window (code 12G4) is as follows: Rectangular window H-E4X16-JI.W-233-12G14GB/T5746--20015 Specifications
5.1.1 The main dimensions of the rectangular window shall comply with the provisions of Table 4: all common parts can be interchangeable. For rectangular windows of similar size, all its parts should be interchangeable. The difference in length between the two diagonals of the main window cabinet and the fan handle should be less than 2Tan. 5.1.2 The surface of the super-shaped window parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have cracks, delamination, burns and other forging defects. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the galvanized layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. After the flushing test in 6.1, there shall be no water leakage or water marks in the inspection parts. 5.1.7 The short window shall have a certain water tightness. After the water pressure test in 6.5, there shall be no leakage in all parts. 5.1.8 The short-circuit should have sufficient strength (see Appendix A (Standard Appendix) and Appendix B (Standard Appendix) for the maximum allowable filling pressure) 1. According to 6.S mechanical strength test. After unloading, the light should be permanently deteriorated.1. The main dimensions of the forged parts shall comply with the provisions of Table 4: All common parts can be interchanged. For rectangular windows of similar size, all parts can be interchanged. The difference between the length of the two diagonals of the main window cabinet and the fan should be less than 2um. 5.1.2 The surface of the forged parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have forging defects such as cracks, delamination, burns, etc. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. 6.1 Water flushing test, there shall be no water leakage or water marks in the inspection part. 5.1.7 The short window should have a certain water tightness, and according to the 6.5 water pressure test, there should be no net leakage in each part. 5.1.8 The short window should have sufficient strength (the maximum allowable pressure is shown in Appendix A (standard appendix) or Appendix B (standard appendix) 1, and the mechanical strength test is carried out according to 6.5. After unloading, the light should be permanently deteriorated.1. The main dimensions of the forged parts shall comply with the provisions of Table 4: All common parts can be interchanged. For rectangular windows of similar size, all parts can be interchanged. The difference between the length of the two diagonals of the main window cabinet and the fan should be less than 2um. 5.1.2 The surface of the forged parts should be flat and smooth, and the surface roughness Ra value should not be greater than 12.5um. 5.1.3 The surface of the die forgings shall not have forging defects such as cracks, delamination, burns, etc. 5.1.4 The weld seams of the welded parts shall be fully welded and the weld surface shall be smooth. 5.7.5 The rectangular window parts shall be hot-dip galvanized according to CB\/Z343, and the thickness of the layer shall not be less than 43mm. The aluminum parts shall be anodized according to CH*/292 after processing, and the surface shall be smooth. 5.1.6 The rectangular window shall have good wind and rain tightness. 6.1 Water flushing test, there shall be no water leakage or water marks in the inspection part. 5.1.7 The short window should have a certain water tightness, and according to the 6.5 water pressure test, there should be no net leakage in each part. 5.1.8 The short window should have sufficient strength (the maximum allowable pressure is shown in Appendix A (standard appendix) or Appendix B (standard appendix) 1, and the mechanical strength test is carried out according to 6.5. After unloading, the light should be permanently deteriorated.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.