JB/T 2001.70-1999 This standard is a revision of JB 2073-84 "Hydraulic drive device for hydraulic press (Pg=63×100000Pa)". This standard specifies the type, size and technical requirements of hydraulic drive devices. This standard is applicable to the power source used by the follow-up hydraulic device composed of the follow-up rotary valve DN15 in JB/T 2001.69-1999 and the hydraulic relay in JB/T 2001.71-1999. This standard was first issued in 1984. JB/T 2001.70-1999 Hydraulic drive device for water system JB/T2001.70-1999 standard download decompression password: www.bzxz.net
Some standard content:
IC.s$ 23.110 Machinery Industry Standard of the People's Republic of China JB/T 2001.1~2001.74—1999 Water system assembly and parts1999-06-28 Issuedbzxz.net National Machinery Industry Bureau 2(-01-U1 Implementation Machinery Industry Standard of the People's Republic of China Water system oil drive device Water system Oil drive device Small standard extremely complete drive cover type, size and technical requirements. JB/T 2001.74—19V9 Generation 2973-84 This standard is applicable to the hydraulic pressure device with the hydraulic follower valve DN5 and the valve B in 2001.71199 according to the new combination of the head of the hydraulic follower valve: 2 Reference standards The following are the meanings contained in the standard, and they are all referenced in the standard and become the provisions of the standard. This standard is published; all the results are effective, and all the requirements are set. The parties who use the standard should explore the possibility of using the following standard version, JB/20U1.6—199, water system/hydraulic valve DN15B20! 19 water system relay distance Required type and size 3 Type and size 3.1 The flow rate of this standard plate pump is only -40L/n and 63L/mn, so as to meet the requirements of various presses with different forging times and force devices respectively. Each gear is divided into three assembly types according to the different output direction of the combination network, as shown in Figure 1) Type National Machinery Industry High-speed Railway 9-24 Approved 2000-01-01 Standard JR/T2001.701999 3, 2 This standard has two oil levels, and the customer can use more oil according to the requirements. 3.3 Type and size are as shown in Figure 2 and Table 1. The system principle is shown in Figure 3, 11 Control digital flow, 2-drop policy-electric line: 3-pool diagram 2 JB/12001.70—190 DP ITAM Medical 3 System original ball diagram M:IxI5 2D0·F1OF Mortal China IRVT 2001.20.1 4 Technical requirements JBT2001.701999 k Digital hydraulic setting 40LiminPN6.3MPa Oil condensation dynamic buttocks 2, 63LminPN 6.3 MPa4.1 Public bad music force 6.3MPa, test pressure side?MPa. The fan p assembly type has type 1, type Ⅱ, and 41 All the components should be pickled before assembly, and the oil tank should be painted with oil-resistant primer. Before assembly, the tank should be connected ten times, and no rack is allowed to stop at: 43 After assembly, liquid test should be carried out to ensure that each part can be operated flexibly. There should be no tears at each seal under the test pressure. 4.4 The main filter (X1125×100-01) must be cleaned to prevent blockage and abnormal suction. 4,5 The low-efficiency liquid level sensor (1: QK-11 type) is used to control the minimum liquid level. The minimum oil level is 300mm! When the suction liquid level is at the low position, the motor is cut off: 4.6~ pressure relay [DP-63 (A) B adjusts two non-return forces, and interlocks with the electric reversing device (24DO-BI0F-T), that is, when the pressure of the pump exceeds the rated pressure of the system, the pressure device (1) acts to make the electromagnetic reversing electromagnetic fast, and the system is corrected: when the pressure of the system drops to the required pressure, the other pressure device (2) acts to make the electric circuit cut off: so that the system is restored to the system 1 working pressure. 5 Marking example Oil drive device with a nominal pressure of 40L/min and a nominal pressure of 6.3MPa, conversion type I: drive device 40L/minPN6.3MPa type JB/T2001.70-99g2:1 Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.