HG/T 20704.9-2000 Format and preparation instructions for the data sheet of professional pump equipment HG/T20704.9-2000 standard download decompression password: www.bzxz.net

Format and preparation instructions for the data sheet of professional pump equipment HG/T20704.9-2000
Subject content and scope of application
This standard specifies the format, content and preparation requirements of the data sheet of professional pump equipment. Applicable to design technology management and quality management.
2 Purpose and edition of equipment data sheet
2.0.1 The data sheet of pump equipment is an important document in the preliminary design and engineering design stage. During the design process, this document is an important basis for the detailed design work of various disciplines. When the project has regulations, it can also be directly used for the inquiry and ordering of pump equipment.
2.0.2 The data sheet of pump equipment can generally be divided into four versions: review version, inquiry version, order version and final version 1 Review version - produced in the early stage of basic engineering design and after receiving the process package from the patentee. This version is only issued when the patentee and the user (owner) require review. 2 The inquiry version is generated during the basic engineering design process and after receiving the review opinions of the patent owner/or user on the review version of the equipment data sheet. It is an important basis for equipment inquiry (when the project stipulates that the equipment data sheet should be used for inquiry and ordering), and it is also the basis for the relevant professionals to carry out detailed design during the engineering design stage. 3 The ordering version is generated after receiving the manufacturer's quotation and before the equipment contract is signed. It is the basis for equipment ordering and detailed design of various engineering professionals.
4 The final version is generated after receiving the final drawings and materials from the manufacturer and no further modifications are expected. It is one of the final design documents provided by the company (institute) to the user (owner). 314
3 The format and content of the equipment data sheet
The pump equipment data sheet is a written document that expresses the requirements of the equipment pump operating conditions, performance structure, material selection, manufacturing, 3.01
inspection in the form of a table, usually prepared in A4 format. The format and content of the pump equipment data sheet are shown in Appendix A, B, C, D, E, F, and G respectively. 3.0.2
Other types of pumps other than the above can be re-formulated according to the characteristics and requirements of the pumps with reference to the above table format.
Instructions for writing equipment data sheets
4.0.1 Pump equipment data sheets usually consist of a homepage and several continuation pages. The homepage should be filled with engineering indexes, process operating conditions, performance parameters, design conditions and regulations, materials and manufacturing requirements related to the pump equipment. 4.0.2 When the pump equipment data sheet is first published, the relevant content and requirements should be filled in as complete and accurate as possible. For some data that can only be obtained through inquiry, such as the efficiency of centrifugal pumps, the required net suction pressure head and other data, they should be filled in before the order version is published after receiving the manufacturer's technical quotation and verification and confirmation. 4.0.3 The equipment data sheet shown in the appendix is ​​a general format. The items with the symbol "" in the table are optional items. When filling in the form, according to the specific conditions and requirements of the equipment, the "mouth" of the relevant items should be blackened and the required data should be filled in the corresponding columns. Columns that are not directly related to the equipment or columns that lack data should not be filled in. 5 Others
5.0.1 In order to facilitate management and ensure that the design work is carried out in an orderly manner, at the beginning of the preliminary design, the person in charge of this profession should uniformly number the machine pump equipment data sheet according to the equipment category and position number sequence of the equipment table according to the relevant regulations of the company (institute) or project, and report to the design manager for summary. When starting to compile the equipment data sheet, the data sheet number summarized by the design manager should be issued to each compiler for use.
5.0.2 In principle, each version of the machine pump equipment data sheet should be modified on the same document. For the part that has been modified or supplemented, the last box of the line (i.e., the modification mark column) should be marked with the same number as the version in the signature column for identification and search. When the modification of the document is carried out on the computer, in addition to the above provisions, the signature of the previous version can be changed to typing on the computer, and the latest version should be signed by the modifier in person. 315
5.0.3 The data sheet of the pump equipment should be reviewed and signed in accordance with the requirements of the data sheet in the "Detailed Rules for Review of Design Documents for Pumps" (HG/T20704.5-2000). Appendix
Appendix A
Appendix B
Appendix C
Appendix D
Appendix E
Appendix F
Centrifugal Pump Data Sheet (Format)
Reciprocating Pump and Metering Pump Data Sheet (Format)
Reciprocating Compressor Data Sheet (Format)
Centrifugal Compressor Data Sheet (Format)
Centrifuge Data Sheet (Format)
Turbine Data Sheet (Format)
Equipment Name:
Conveying Medium
Medium Characteristics
Solid Content
Same Particle Size
Appendix A
Centrifugal Pump Data Sheet|| tt||Position number:
Number of units:
Toxic
Corrosive
Density at normal temperature
Viscosity at normal temperature
Vaporization pressure at normal temperature
Operation status
Installation position
Atmospheric pressure
Required NPSH
Closed
Wear ring
|Continuous
mPa·s
MPa·A
Intermittent
Inlet pressure
Outlet pressure
Rated pressure difference
Project number
File number||tt| |Page 1 of 2
User:
Address:
Effective NPSH
Installation environment and site conditions
口Indoor口Outdoor口Heating口No heating
kPa·A
Minimum continuous
口Semi-open
口Single suction
Transmission mode
口Direct connection
Coupling
口V-belt
口Open
口Double suction
Transmission
口Elastic pins口Intermediate spacer sleeves口Diaphragms
口Pump driver common
Steering (from the driving end)
口Pump driver separation||tt| |口Clockwise
Shaft sleeve outer diameter
口Counterclockwise
口Single end
口Double end||Tandem type
Internal type
External type
Balanced type
Port unbalanced typeManufacturer
Port Packing seal
Port Water seal ring
Grinding ring (pump body/impeller)
Port with auxiliary impeller
Ambient temperature
Explosion area
Operating point efficiency
Shaft power
Support mode
Pump segmentation
Grinding ring
Design pressure
Port foot
Port diameter
Connecting pipe DN.mm
Flange standard
Shaft thrust
Bearing lubrication method
Water cooling jacket
口Without auxiliary impeller
Center line
口Axial
Hydrostatic test
PN(MPa
口Rolling
口Moving
Flange surface
MPa·G
MPa·G
口Bracket
口Type
口Horizontal口Vertical
口Horizontal door vertical
口Sliding
口Sliding
口Forced
口Other types of seals
Mechanical dynamic ring
Seal auxiliary seal ring
Water seal ring
口Oil bath
Equipment name:
Shaft seal pipeline code:
Shaft seal name
Washing water pressure
Minimum required immersion depth
口Electric motor
Appendix A (Continued)
Centrifugal pump data sheet
(Continued)
(According to)
MPa·G
口 Steam turbine (data sheet file number
Rated power
口 Mechanical operation test
口 Water pressure test
口 Special requirements
口 Base
口 Driver
口 Anchor bolts
口 Random spare parts [with list]
口 Shaft seal piping system
Transmission device
Driver
口 Coupling and guard
口 Lubricating oil system
Project number||tt| |Document No.
Page 2 of 2
Position No.:
Cooling Plan:
Cooling Pressure
Pump Bottom Plate to Suction Port
Suction Port to Tank Bottom
Protection Level
Insulation Level
Explosion-proof Level
Manufacturer
口Performance Test
口Cavitation Test
口Two Years of Operation Spare Parts [List Attached]
Maximum Maintenance Parts
Note: The manufacturer shall fill in the blank columns in the table and return it to the design unit. 2
口Pulley, Belt and Guard
口Special Tools
External Shape and size
Field for filling in by manufacturer
Name of repair equipment:
Model:
Conveying medium
Medium characteristics
Solid content
Solid particle size
Data sheet of reciprocating pump and metering pump
Position number:
Number of units:
口Toxic
口Corrosive
Density at normal temperature
Viscosity at normal temperature
Vaporization pressure at normal temperature
Operating state
Installation position
Atmospheric pressure
Flow rate (maximum)||tt ||Shaft power
(Piston)
Coupling
Buffer
Port Continuous
Port Intermittent
Indoor port Outdoor port Heating
Number of reciprocating strokes
Type port Diaphragm type
Type port Single acting
Design pressure
DN·mm
mmStroke
MPa·A
Port No heating
kPa·A
Times/min
Port Single port Double port Plunger type
Port Double acting
Valve type
Design temperature
PN(MP a) Flange surface
口Elastic diaphragm
口Elastic pin
口Pump driver common
Buffer volume
口Diaphragm type
口Diaphragm type
口HorizontalPort vertical
口HorizontalPort vertical
口Pump driver separation
口Gas-liquid contact
口Gas-liquid contact
Inlet pressure
Outlet pressure
Rated pressure difference
Project No.
Document No.
Page 1
User:
Factory address:
Effective cavitation margin
Ambient temperature
Explosion area
Measuring accuracy
Power end
Lubrication method
Shaft type
Sealing flow
Cooling pressure
口Speed ​​change
口Electric
口Crank connecting rod
口Direct connection
口Forced
Total 2 pages
口Adjust stroke
口Pneumatic
口Eccentric wheel
口Gearbox
MPa·G
MPa·G
口Bypass
口Manual
口N-type shaft
口Belt transmission Dynamic
口Oil bath
Flushing liquid name
口Stuffing box
MPa·G
口Bearing box
MPa·G
Type|Gear|Hydraulic|Belt||Worm gear model
Lubrication system
Safety valve
Inside the pump
(See data sheet file number)
Set pressure
口Independent
MPa·G
Equipment name:
Type|Electric motor
Mechanical operation test
口Performance test
口Special requirements
Piston rod||tt ||Appendix B (Continued)
Data Sheets for Reciprocating and Metering Pumps
(Continued)
Valve Springs
口 Steam Turbine (Data Sheet File No.
Rated Power
口 Driver
口 Pulley, Belt and Guard
口 Transmission
口 Coupling and Guard
口 Anchor Bolts
口 Base
口 Lubricating Oil System
Monitoring Instruments
Maximum Repair Parts
Transmission
Note: The manufacturer shall complete the blank columns in the table and return them to the design unit. Edition
Protection level
Insulation level
Explosion-proof level
Manufacturer
Port Water pressure test
Port Stability accuracy
Port Repeatability
Port Import buffer
Port Special tools
Project No.
File No.
Page 2 of 2 pages
Position No.:
Packing ring
Test pressure
Port Export buffer
Port Random spare parts (with list)
Port Two-year operation spare parts (with list)
Overall dimensions
Port Safety room
Manufacturer’s fill-in column
MPa·G
Repair equipment name:
(Dry/Wet) Nm/h
(Dry/Wet) m/h
(Normal/Design)
(Normal/Design)
Compressibility coefficient
mPa·A
Zi or Z average
K, or K level
Adiabatic index (C/C)
(Normal/Design)
(Normal/Design)
Compressibility coefficient
MPa·A
Z2 or E level
Adiabatic index (Cp/Cv)
Shaft power
Total shaft power
Molecular weight
K,Or K Pinghai
(Compressor crankshaft)
Reciprocating compressor data sheet
Position number:
Number:
Volume percentage
Installation location
Abnormal conditions
Explosion area
Project number
File number
Page 1 of 5 pages
User:
Factory address:
Parts (single machine)
Total shaft power (including transmission loss)||t t||Installation environment and site conditions
口Indoor口Outdoor口Heating口Non-heating
口Humid tropical口Dust口Corrosive gas
℃Allowable temperature rise
Maximum pressure drop
Normal pressure dew point
℃Inlet water
MPaFouling coefficient
MPa·G
Atmospheric pressure
Relative humidity
Environmental humidity
Less than 200kW
Supply greater than 200kw|| tt||Emergency power supply
DC power supply
Average molecular weight
kPa·A
Name of repair equipment:
Number of cylinders at each level/action form
Inner diameter of cylinder
Relief volume
Number of valves
Valve form
Piston force of each column
Set pressure of safety valve
Hydraulic pressure test pressure
Average piston speed
(intake/exhaust)||tt ||(Pull/Compression)
MPa·G
MPa·G
Maximum allowable piston force
Piston rod diameter
Cylinder lubrication port with oil port without oil
Open type
Extended single chamber type
Cylinder liner
Piston ring
Support ring
Piston rod
Spring
Valve limiter
Crosshead
Closed type
Appendix C (Continued)
Reciprocating compressor data sheet
(Continued)
Cooling port Yes No
Port Standard type
Port Double chamber type
Piston rod packing
Lubrication port Yes No
Nitrogen flow
Port Required
Project No.
File No.
Page 2 of 5
Position No.:
Cooling port Water cooling port Oil cooling
Port Not required
Discharge gas pressure bzxZ.net
Transmission mode
口Direct connection
Steering (from the driving end)
Winding device
MPa·G
MPa·G
口V-belt口Gear box
口Clockwise
口Electric
口Counterclockwise
口Pneumatic口Manual
Equipment name:
Adjustment range
Adjustment method口Suction valve opening
Circulation volume
Appendix C (Continued)
Reciprocating compressor data sheet
(Continued)
Variable clearance volume
Pressure
Gear
Drive mode
Screw
Crankshaft
Oil brand
Electric motor
Gear Screw
Drive mode
Buffer
Oil filling amount
Crankshaft
Drive mode
Intercooler
Separator
Muffler
Interstage piping
Inlet filter| |tt||Safety valve
Type
Rated power
Protection level
Maximum power
Rated steam consumption
Power kw
Heat transfer area
Total length
口Electric motor
Oil brand
口Crankshaft
Project number
File number
Page 3
Total 5 pages
Position number:
Control mode Pneumatic
口Electric口Hydraulic口Automatic口Manual
口Suction valve unloader
MPa·G
MPa·G
口Bypass
口Speed ​​change
Material (tube/bright body)
Heat exchange area
Filter accuracy
Before filter
After filter
Heating method
Oil filling amount at one time
口Electric motor
Overall dimensions
kw speed
Insulation grade
Main driving machine
Overall dimensions
Overall dimensions
Overall dimensions
Overall dimensions
Overall dimensions
Main oil pump motor
口Carbon steel
口Carbon steel
Shell material
Filter cartridge material
口Stainless steel
口Stainless steel
口Steam
Installation position口Initial inlet
口Intermediate stage
Model speed ratio
Belt specification number
Outer diameter of large pulley
Outer diameter of small pulley
Auxiliary oil pump motor
Lubricator motor
口Final outlet
Electric heater
Instrument power supply
Equipment name:
Inlet pressure
Inlet water temperature|| tt||Pressure drop
Steam temperature
Instrument air
Control system
Normal pressure
MPa·G
Appendix C (continued)
Reciprocating compressor data sheet
(continued)
Compressor cylinder
Process conditions
Oil cooler
MPa·G
Steam consumption
MPa·GTotal consumption
Control and instrumentation
Type Pneumatic Port Electric
Main lubricating oil pump outlet
Auxiliary lubricating oil pump outlet
Lubricating oil Lubricating oil filter pressure difference
Process gas inlet initial
Process gas outlet initial
Process gas inlet
Intercooler
Aftercooler
Port each stage
Port each stage
Port outlet
Port gas
Port gas
Lubricating oil (fuselage)
Lubricating oil (cooling place)
Packing cooling water
Cooling water flowmeter
Pressure transmitter
Level transmitter
Alarm buzzer
Exhaust pressure high
Intake pressure Low
and high exhaust temperature
Low lubricating oil pressure
口Final
口Final
High oil filter pressure drop
Auxiliary oil pump starting failure
口Each stage
口Each stage
口Each stage
口Electronic
口Hydraulic
Document No.
Page 4 Page 5
Position No.:
Gas cooler
Mode|Manual|Automatic
Cooling water inlet and outlet main pipe
Cylinder cooling water
Main radial bearing
Motor bearing
口Export
口Import
Large vibration of compressor
High temperature of main bearing
Low nitrogen sealing pressure
On-site installation
Equipment name:
口Compressor
口Belt drive
口Inlet filter
口Aftercooler
口Interstage pipeline
口Lubricating oil system
口Special tools
口Driver
口Coupling
口Buffer
口Buffer
口Safety gap
Appendix C(Continued)
Reciprocating compressor data sheet
Continued)
口Reducer
口Transmission cover
口Intercooler
口Muffler
口Turn-turn device
口Instruments and instrument panel
口Anchor bolts
口Send-on accessories
口Manufacturer standard test
口Cylinder water pressure test
口Cylinder air tightness test
口Mechanical operation test
口Turn-turn clearance inspection| |tt||Compressor weight
Driver weight
Total weight
Project number
Document number
Page 5 of 5
Position number:
口Random accessories (with list)
口Two-year operating spare parts (with list)
口Two-year operating spare parts
Inspection and test
口Cylinder liner water pressure test
口Lubricating oil console operation test
The manufacturer shall fill in the blank columns in the table and return it to the design unit. Edition
Maximum installation weight
Maximum maintenance weight
Piston removal distance
Column to be filled in by the manufacturer
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.