This standard specifies the technical requirements, test methods, inspection rules, packaging, marking, transportation and storage of steel axes. This standard applies to all types of steel axes. GB/T 8389-2003 General Technical Requirements for Steel Axe GB/T8389-2003 Standard download decompression password: www.bzxz.net

GB/T83B9-20C3
According to the original national economic! Industry to the national light 1399.2 meaning, "in the release of economic professional standards, clean up the entire part of the national standard for the light industry standard is relatively accurate, the B939.3-19 reduction test method has been transformed into QB/1385321; the original GB8389.4.15878 calculation of the inspection rules, signs, packaging, transportation and pregnancy 2 has been transformed into: QB/3857.19: the original 39.5-1576 safety account has been branded as Q/3857.419, standard -BT8389.?19X will be general technical cases and B/3857.8857.4-1 02 is expected to be set. This standard is more difficult than the above standard:
has trained the necessary technical personnel, and has made extensive adjustments to the content of the document, and has completed the product test head (Sichuan etc.) This standard is the same as the standard 1N2?: 37 steel and the common technical conditions are more related, the standard is a common record,
Yun standard Chinese to the Light Industry Federation of the National Standard Center for the International Standardization of the car sheep: Shanghai to the tool industry Yan Institute of the cup standard Feng must start from the Chinese people, welcome Germany, can increase the dragon and good: this analysis of the current trend of the standard version of the fluorescent Asia world match: G?T R.an. 2ISS?.
1 Scope
General technical parts for steel pipes
This standard specifies the technical requirements, test methods, inspection, packaging, marking, transportation and storage of various valves. The main standard applies to all kinds of valves
2 Normative references
GB/T8389—2003
The clauses in the above documents are the effective date of this standard and are the referenced documents of the previous period. All subsequent documents (excluding the referenced documents) shall apply to all types of valves. It is difficult to use the latest version of the material, however, the parties who have reached an agreement on the use of the latest version of these documents can use the latest version of these documents. For any referenced document with a later date, the latest version shall apply to this standard. GE/T2:0 Thick strip hardness reading method (G1/1230-1991, 441906F08: 1986) GB/T1941 Wood hardness test method (G/T1941-1991GV[S850: 1975) (B/T28K Source batch inspection method for effective shaft sample Process hall and sample table (with ten consecutive batches of guns to check! CB Ting 530 hand tool packaging, standard table, total output and heart 3 technical requirements
3.1 Surface quality
3.1.1 Surface quality: the surface of the part is R, the sound is original. 1m.3.1.2 The head shall not have defects such as number effect, head layer, gorge, paint cannot be separated, there is flow, bubble and other defects. 3.1.3 The polishing plate shall not have cracks, hair, quality, mold and knots and other defects. 3.1.4 The machine shall not be obviously deflected: ||tt| |3.2 Tolerance of the quality of the head
The quality tolerance of the head should not be greater than 165%.
3.3 Moisture content of the handle
The moisture content of the handle should not be greater than 165.
3.4 Hardness
The hardness of the head is 48HRC~56HRC, and the hardness of the head should not be greater than 165..3.5 Performance
3.5.: The wear part should be able to break out, and no cracks, damage, etc. should occur. 3.5.2 The handle should be able to break out when a certain tensile force is applied. Table 1 Tensile force of the handle
Head quality/kg
. 7 ..1. .
3.5.3 Disposable conditions! . Can smoothly use the pool without village 3.6 Safety rules
The steel case is used in accordance with the provisions of Appendix A. 4 Test methods
4.1 Dimensional inspection
13 core
GB/T8389-2C03
The dimensions of the steel are tested by the same principle
4.2 Surface measurement inspection
4.2.1 The outer diameter of the steel is measured by the external gauge.
4.2.2 The surface of the head is checked against the standard plate. 43 Quality inspection
and test
4.4 Moisture content test
The annual water content should be tested by moisture content test, 4.5 Hardness test
and hardness test according to GB/T350. 4.E Performance test
4.6.1 The annual pilot test is carried out in a small special testing machine in the hospital. During the test, special tools are used to maintain the loss rate. The center of the test is within the range of 15m2mm, and the range is within 30% of the production line. The test should be carried out according to the specifications.
1. Analysis. Slurry
1# Head:
5 Years:
Contact:
Scale,
Figure 1 Punch test machine
Table? Impact test
Deep meaning
4.6.2 The pull-off test with a large test shoe is run on the test shoe. 1 9-.2.5
Single old special ten points
4.6.3 The steel and other wood with a strength of not less than MTa must be cut and tested. After the test, the head should show the phenomenon of edge, cracking, etc., and the valve cannot move. The materials used for inspection are safe (according to the provisions of 111 of the engineering), and the inspection is carried out according to the provisions of 2
5 Quick inspection rules
5.1 The product can be inspected and qualified! The product certificate is required. 5.2 The ordering party requires the wood exploration product to be individually adjusted. 5.3 The product sampling shall be carried out according to the secondary sampling method formulated by GB/T8389—2003
54 The classification and classification of unqualified products shall be carried out according to the qualified quality level (AQL.) of the wood powder inspection (<1L) as specified in Table 3. Table 3 Classification and grouping of nonconforming items, inspection items, qualified quality level (4(L) and inspection width level (IL). Number
Nonconforming items
Pull test
Shock test bzxz.net
Light inspection items
Volume control test Size test
Inspection room
Energy release test
Strict inspection rate
Qualified quality level (A
For nonconforming products found in the inspection and samples with low cycle after transportation and reconditioning, the manufacturer shall replace the rejected batches of products, which may be reclassified or reconditioned by the manufacturer and submitted for inspection and modification. 5.6
6 Packaging, marking, transportation and storage
The packaging, marking, transportation and storage of products shall be carried out according to the G1/T heat treatment level (4 level (1 1.2
T8389—2003
Time Record
(Normative Appendix)
The following are the rules for the use of steel products in China. To prevent the occurrence of foreign accidents, manufacturers should follow these rules in product instructions and product publicity.
A.1 The price of steel products should be limited according to the purpose. 4.2 Do not use the products for hammering operations (see Figure A.1): 4
.3 The hammer chain of this product shall not be used, or the hammer head shall be used in close contact with the hammer head. Figure A.2
.4 The steel side shall be inspected to ensure the correct use. A.5 The handle can be used after the steel handle is loose. AE The head of the pin is cracked at any part of the lower part.
Tip: This standard content only shows part of the intercepted content of the complete standard. If you need the complete standard, please go to the top to download the complete standard document for free.